Emulsion polymerization particle stability

Thus these polymerizations begin as precipitation polymerizations but become emulsion polymerizations upon stabilization of the polymer particles. 

Kusters et al. [42] showed that the desorption rate constant for monomeric radicals decreases signihcantly, compared to anionic surfactant, in the emulsion polymerization stabilized by n-nonylphenoxypolyethoxy ethanol with an average of 30 ethylene oxide units per molecule. This result implies that there exists a steric barrier surrounding the latex particle that retards the entry (or exit ) of free radicals for the emulsion polymerization system stabilized by nonionic surfactant. More research efforts are required to reconcile this controversial issue. 

Styrene and methyl methacrylate in the presence of the rubber seed latex particles. Finally, glycidyl methacrylate was grafted onto the composite latex particles. The emulsion polymerizations were stabilized by sodium dihexyl sulfosuccinate and initiated by potassium persulfate. The functionalized composite polymer particles, which served as an impact modifier, were blended with polyamide-6, and these particles were dispersed well in the matrix of polyamide-6. 

Figure C2.3.11 Key surfactant stmctures (not to scale) in emulsion polymerization micelles containing monomer and oligomer, growing polymer particle stabilized by surfactant and an emulsion droplet of monomer (reservoir) also coated with surfactant. Adapted from figure 4-1 in [67],...

Emulsion Process. The emulsion polymerization process utilizes water as a continuous phase with the reactants suspended as microscopic particles. This low viscosity system allows facile mixing and heat transfer for control purposes. An emulsifier is generally employed to stabilize the water insoluble monomers and other reactants, and to prevent reactor fouling. With SAN the system is composed of water, monomers, chain-transfer agents for molecular weight control, emulsifiers, and initiators. Both batch and semibatch processes are employed. Copolymerization is normally carried out at 60 to 100°C to conversions of - 97%. Lower temperature polymerization can be achieved with redox-initiator systems (51). 

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

Emulsion Polymerization. When the U.S. supply of natural mbber from the Far East was cut off in World War II, the emulsion polymerization process was developed to produce synthetic mbber. In this complex process, the organic monomer is emulsified with soap in an aqueous continuous phase. Because of the much smaller (<0.1 jira) dispersed particles than in suspension polymerization and the stabilizing action of the soap, a proper emulsion is stable, so agitation is not as critical. In classical emulsion polymerization, a water-soluble initiator is used. This, together with the small particle size, gives rise to very different kinetics (6,21—23). 

The product of an emulsion polymerization is a latex ie, polymer particles on the order of 0.5—0.15 p.m stabilized by the soap. These form the basis for the popular latex paints. SoHd mbber is recovered by coagulating the latex with ionic salts and acids (see Latex technology). 

Soap. A critical ingredient for emulsion polymerization is the soap (qv), which performs a number of key roles, including production of oil (monomer) in water emulsion, provision of the loci for polymerization (micelle), stabilization of the latex particle, and impartation of characteristics to the finished polymer. 

A typical recipe for batch emulsion polymerization is shown in Table 13. A reaction time of 7—8 h at 30°C is requited for 95—98% conversion. A latex is produced with an average particle diameter of 100—150 nm. Other modifying ingredients may be present, eg, other colloidal protective agents such as gelatin or carboxymethylcellulose, initiator activators such as redox types, chelates, plasticizers, stabilizers, and chain-transfer agents. 

Many different combinations of surfactant and protective coUoid are used in emulsion polymerizations of vinyl acetate as stabilizers. The properties of the emulsion and the polymeric film depend to a large extent on the identity and quantity of the stabilizers. The choice of stabilizer affects the mean and distribution of particle size which affects the rheology and film formation. The stabilizer system also impacts the stabiUty of the emulsion to mechanical shear, temperature change, and compounding. Characteristics of the coalesced resin affected by the stabilizer include tack, smoothness, opacity, water resistance, and film strength (41,42). 

Partially hydrolyzed poly(vinyl alcohol) grades are preferred because they have a hydrophobic /hydrophilic balance that make them uniquely suited for emulsion polymerization. The compatibUity of the residual acetate units with the poly(vinyl acetate) latex particles partly explains the observed stabilization effect. The amount of PVA employed is normally 4—10% on the weight of vinyl acetate monomer. The viscosity of the resulting latex increases with increasing molecular weight and decreasing hydrolysis of the PVA (318). 

An example of liquid/liquid mixing is emulsion polymerization, where droplet size can be the most important parameter influencing product quality. Particle size is determined by impeller tip speed. If coalescence is prevented and the system stability is satisfactory, this will determine the ultimate particle size. However, if the dispersion being produced in the mixer is used as an intermediate step to carry out a liquid/liquid extraction and the emulsion must be settled out again, a dynamic dispersion is produced. Maximum shear stress by the impeller then determines the average shear rate and the overall average particle size in the mixer. 

Suspension polymerization produces beads of plastic for styrene, methyl methacrviaie. viny l chloride, and vinyl acetate production. The monomer, in which the catalyst must be soluble, is maintained in droplet fonn suspended in water by agitation in the presence of a stabilizer such as gelatin each droplet of monomer undergoes bulk polymerization. In emulsion polymerization, ihe monomer is dispersed in water by means of a surfactant to form tiny particles held in suspension I micellcsK The monomer enters the hydrocarbon part of the micelles for polymerization by a... 

Monosized polystyrene particles in the size range of 2-10 /am have been obtained by dispersion polymerization of styrene in polar solvents such as ethyl alcohol or mixtures of alcohol with water in the presence of a suitable steric stabilizer (59-62). Dispersion polymerization may be looked upon as a special type of precipitation polymerization and was originally meant to be an alternative to emulsion polymerization. The components of a dispersion polymerization include monomers, initiator, steric stabilizer, and the dispersion medium... 

A key factor in doing a successful suspension polymerization is the composition of the aqueous phase or stabilizer. Too much stabilizer results in emulsion polymerization, which produces small particles (less than 1 /cm). Too little stabilizer results in bulk polymerization. For the production of GPC gels, the ratio of aqueous phase to organic phase should be about 2 1. 

The polymerization reaction is conducted at the desired temperature with a slow stirring regime for a certain period. A typical recipe for the emulsion polymerization of styrene is exemplified in Table 1 [40]. As seen here, potassium persulfate and sodium dodecyl sulfate were used as the initiator and the stabilizer, respectively. This recipe provides uniform polystyrene particles 0.22 /Lim in size. 

The function of emulsifier in the emulsion polymerization process may be summarized as follows [45] (1) the insolubilized part of the monomer is dispersed and stabilized within the water phase in the form of fine droplets, (2) a part of monomer is taken into the micel structure by solubilization, (3) the forming latex particles are protected from the coagulation by the adsorption of monomer onto the surface of the particles, (4) the emulsifier makes it easier the solubilize the oligomeric chains within the micelles, (5) the emulsifier catalyzes the initiation reaction, and (6) it may act as a transfer agent or retarder leading to chemical binding of emulsifier molecules to the polymer. 

In another study, uniform composite polymethyl-methacrylate/polystyrene (PMMA/PS) composite particles in the size range of 1-10 fim were prepared by the seeded emulsion polymerization of styrene [121]. The PMMA seed particles were initially prepared by the dispersion polymerization of MMA by using AIBN as the initiator. In this polymerization, poly(7V-vinyl pyrolli-done) and methyl tricaprylyl ammonium chloride were used as the stabilizer and the costabilizer, respectively, in the methanol medium. Seed particles were swollen with styrene monomer in a medium comprised of seed particles, styrene, water, poly(7V-vinyl pyrollidone), Polywet KX-3 and aeorosol MA emulsifiers, sodium bicarbonate, hydroquinone inhibitor, and azobis(2-methylbu-... 

Adsorption behavior and the effect on colloid stability of water soluble polymers with a lower critical solution temperature(LCST) have been studied using polystyrene latices plus hydroxy propyl cellulose(HPC). Saturated adsorption(As) of HPC depended significantly on the adsorption temperature and the As obtained at the LCST was 1.5 times as large as the value at room temperature. The high As value obtained at the LCST remained for a long time at room temperature, and the dense adsorption layer formed on the latex particles showed strong protective action against salt and temperature. Furthermore, the dense adsorption layer of HPC on silica particles was very effective in the encapsulation process with polystyrene via emulsion polymerization in which the HPC-coated silica particles were used as seed. 

Dispersion polymerization involves an initially homogeneous system of monomer, organic solvent, initiator, and particle stabilizer (usually uncharged polymers such as poly(A-vinyl-pyrrolidinone) and hydroxypropyl cellulose). The system becomes heterogeneous on polymerization because the polymer is insoluble in the solvent. Polymer particles are stabilized by adsorption of the particle stabilizer [Yasuda et al., 2001], Polymerization proceeds in the polymer particles as they absorb monomer from the continuous phase. Dispersion polymerization usually yields polymer particles with sizes in between those obtained by emulsion and suspension polymerizations—about 1-10 pm in diameter. For the larger particle sizes, the reaction characteristics are the same as in suspension polymerization. For the smallest particle sizes, suspension polymerization may exhibit the compartmentalized kinetics of emulsion polymerization. 

The largest portion of the monomer (>95%) is dispersed as monomer droplets whose size depends on the stirring rate. The monomer droplets are stabilized by surfactant molecules absorbed on their surfaces. Monomer droplets have diameters in the range 1-100 pm (103-105 nm). Thus, in a typical emulsion polymerization system, the monomer droplets are much larger than the monomer-containing micelles. Consequently, while the concentration of micelles is 1019-1021 the concentration of monomer droplets is at most 1012-1014 L 1. A further difference between micelles and monomer droplets is that the total surface area of the micelles is larger than that of the droplets by more than two orders of magnitude. The size, shape, and concentration of each of the various types of particles in the... 

The reaction described in this example is carried out in miniemulsion.Miniemulsions are dispersions of critically stabilized oil droplets with a size between 50 and 500 nm prepared by shearing a system containing oil, water,a surfactant and a hydrophobe. In contrast to the classical emulsion polymerization (see 5ect. 2.2.4.2), here the polymerization starts and proceeds directly within the preformed micellar "nanoreactors" (= monomer droplets).This means that the droplets have to become the primary locus of the nucleation of the polymer reaction. With the concept of "nanoreactors" one can take advantage of a potential thermodynamic control for the design of nanoparticles. Polymerizations in such miniemulsions, when carefully prepared, result in latex particles which have about the same size as the initial droplets.The polymerization of miniemulsions extends the possibilities of the widely applied emulsion polymerization and provides advantages with respect to copolymerization reactions of monomers with different polarity, incorporation of hydrophobic materials, or with respect to the stability of the formed latexes. 

---