Sodium dihexyl sulfosuccinate

Sulfobutanedioio acid 1,4-bis(1 -methylpentyl) ester sodium sail. Alphasol MA Aerosol MA Bis(l-methylamyl) sodium sulfosuccinate Butanedioic acid, sulfo-, 1,4-bis(1-methylpentyl) ester, sodium salt Oihexyl sodium sulfosuccinate EINECS 227-847-0 Lankropol KMA Sodium dihexyl sulfosuccinate Sodium 1,4-diisohexyl 2-sulphosucoinate. Emulsifier, wetting agent, especially in solutions of electrolytes used as a solubilizer for soaps, emulsion polymerization aid. Solid soluble in H2O, pine oil, oleic acid, MezCO, kerosene, CCI4, EtOH, CsHe, hot olive oil, glycerol insoluble in liquid petrolatum. Harcros. 

Examples of surfactants with sulfosuccinate hydrophiles include many of the surfactants in the Cytec Aerosol line (e.g. Aerosol MA-80, sodium dihexyl sulfosuccinate, with cmc = 1.0% a vety commonly utilized surfactant in emulsion polymerization is Aerosol OT-75, sodium dioctyl sulfosuccinate, which has cmc = 0.07% and Aerosol AY-65 is sodium diamyl sulfosuccinate with... 

An investigation paralleling the preceding work was conducted on the VAc/methyl acrylate system [22]. For a 50/50 molar ratio with Aerosol MA (sodium dihexyl sulfosuccinate)/HD as the surfactant system, similar results were found as above the number of particles was proportional to [I]° ... 

Chem. Descrip. Sodium dihexyl sulfosuccinate in water (15%) and isopropanol (5%)... 

CAS 3006-15-3 2373-38-8 6001-97-4 EINECS/ELINCS 221-109-1 Synonyms Bis (1-methylamyl) sodium sulfosuccinale Butanedioic acid, suifo-. 1.4-dihexyl ester, ium salt Dihexyl sodiosulfosuccinate Dihe) l sulfosuccinale sodium salt Sodium dihexyl sulfosuccinate Sodium di-(2-methylpentyl) sulfosuccinate Sulfosuccinic acid, suifo-, 1,4-dihe) ester, sodium salt... 

Sodium dihexyl sulfosuccinate. See Dihexyl sodium sulfosuccinate... 

Sodium di (2-ethylhexyl) sulfosuccinate. See Dioctyl sodium sulfosuccinate Sodium 1,4-diheptyl sulfobutanedioate Sodium 1,4-diheptyl sulfonatosuccinate. SeeDiheptyl sodium sulfosuccinate Sodium dihexyl sulfosuccinate. See Dihexyl sodium sulfosuccinate... 

Figure 3. Solubility enhancement of Hill contaminant by 8% sodium dihexyl sulfosuccinate, 8% IP A and sodium chloride.

The addition of xanthan gum polymer did not affect phase behavior. This was evidenced by the close match between the volume fraction diagrams for a surfactant solution (4% sodium dihexyl sulfosuccinate, 8% IPA) with 500 mg/1 xanthan gum polymer and without polymer as shown in Figure 2. As shown in Figure 4, the viscosity of the surfactant solution is increased by the addition of polymer. All samples with polymer were observed to coalesce to microemulsions in less than 20 hours, which is still fast enough to be acceptable based upon subsequent column floods. 

Sodium Dihexyl Sulfosuccinate, 8% IP A, 500 mg/1 Xanthan Gum 8%Sodium Dihexyl Sulfosuccinate, 0 mg/1 Xanthan Gum... 

C5 = Sodium diamyl sulfosuccinate C6 = Sodium dihexyl sulfosuccinate C8 = Sodium dioctyl sulfosuccinate SBA = Secondary butyl alcohol xg = xanthan gum... 

In experiment DW 2, the permeability was decreased from an initial value of 15.4 Darcy to a final waterflood value of 1.5 Darcy. Column DW 5 was plugged as a result of surfactant flooding. In both experiments, a surfactant mixture with sodium dioctyl sulfosuccinate was used without enough cosolvent to prevent gels. Sodium dihexyl sulfosuccinate is less prone to forming gels and less alcohol is needed to eliminate gel when it... 

Surfactant retention (adsorption plus any other phenomena that might cause retention) was measured by injecting a surfactant solution containing radiolabeled sodium dihexyl sulfosuccinate into a column packed with contaminated Hill field soil. Tritiated water was used as a conservative tracer. Figure 13 shows the effluent concentration from the column for both these labeled molecules as measured by liquid scintillation counting. The almost identical breakthrough and elution of these molecules indicate very low adsorption of the surfactant on this soil. 

Styrene and methyl methacrylate in the presence of the rubber seed latex particles. Finally, glycidyl methacrylate was grafted onto the composite latex particles. The emulsion polymerizations were stabilized by sodium dihexyl sulfosuccinate and initiated by potassium persulfate. The functionalized composite polymer particles, which served as an impact modifier, were blended with polyamide-6, and these particles were dispersed well in the matrix of polyamide-6. 

Chem. Descrip. Sodium dihexyl sulfosuccinate (78-80%), IPA (5%), water CAS 2373-38-8 67-634) EINECS/ELINCS 221-109-1 200-661-7 UN 1993 Uses Surfactant Regulatory Canada DSL listed... 

---