Crystalline propylene

In crystalline propylene-coethylene copolymers with low contents of ethylene units, the type of defects in both intramolecular and intermolecular structure as... 

Polyolefins. In these thermoplastic elastomers the hard component is a crystalline polyolefin, such as polyethylene or polypropylene, and the soft portion is composed of ethylene-propylene rubber. Attractive forces between the rubber and resin phases serve as labile cross-links. Some contain a chemically cross-linked rubber phase that imparts a higher degree of elasticity. 

Oxidation of a glycol can lead to a variety of products. Periodic acid quantitatively cleaves 1,2-glycols to aldehydes and is used as an analysis method for glycols (12,13). The oxidation of propylene glycol over Pd/C modified with Pb, Bi, or Te forms a mixture of lactic acid, hydroxyacetone, and pymvic acid (14). Air oxidation of propylene glycol using an electrolytic crystalline silver catalyst yields pymvic aldehyde. 

Both propylene and isobutylene ate comonomers that are incorporated along the chain, resulting in additional short-chain branching. One important factor in controlling polymer crystallinity is the choice of chain-transfer agent. Ethane and methane, for example, are inefficient agents whose presence in the monomer feed stream must be considered in reaction control. 

Similarly, the random introduction by copolymerization of stericaHy incompatible repeating unit B into chains of crystalline A reduces the crystalline melting point and degree of crystallinity. If is reduced to T, crystals cannot form. Isotactic polypropylene and linear polyethylene homopolymers are each highly crystalline plastics. However, a random 65% ethylene—35% propylene copolymer of the two, poly(ethylene- (9-prop5lene) is a completely amorphous ethylene—propylene mbber (EPR). On the other hand, block copolymers of the two, poly(ethylene- -prop5iene) of the same overall composition, are highly crystalline. X-ray studies of these materials reveal both the polyethylene lattice and the isotactic polypropylene lattice, as the different blocks crystallize in thek own lattices. 

Salts and Derivatives. Generally the vitamers are high melting crystalline soHds that are very soluble in water and insoluble in most other solvents. Properties of the common forms are Hsted in Table 1. The only commercially important form of vitamin B is pytidoxine hydrochloride (7). This odorless crystalline soHd is composed of colorless platelets melting at 204—206°C (with decomposition). In bulk, it appears white and has a density of - 0.4 kg/L. It is very soluble in water (ca 0.22 kg/L at 20°C), soluble in propylene glycol, slightly soluble in acetone and alcohol (ca 0.014 kg/L), and insoluble in most lipophilic solvents. A 10% water solution shows a pH of 3.2. Both the hydrochloride and corresponding free base sublime without decomposition (16). 

Boron Bromide. Approximately 30% of BBr produced in the United States is consumed in the manufacture of proprietory pharmaceuticals (qv) (7). BBr is used in the manufacture of isotopicaHy enriched crystalline boron, as a Etiedel-Crafts catalyst in various polymerization, alkylation, and acylation reactions, and in semiconductor doping and etching. Examples of use of BBr as a catalyst include copolymerization of butadiene with olefins (112) polymerization of ethylene and propylene (113), and A/-vinylcarbazole (114) in hydroboration reactions and in tritium labeling of steroids and aryl rings (5). 

Polymerization. Supported catalysts are used extensively in olefin polymerization, primarily to manufacture polyethylene and polypropylene. Because propylene can polymerize in a stereoregular manner to produce an isotactic, or crystalline, polymer as well as an atactic, or amorphous, polymer and ethylene caimot, there are large differences in the catalysts used to manufacture polyethylene and polypropylene (see Olefin polymers). 

Polypropylene. There is an added dimension to the catalytic polymerization of propylene, since in addition to the requirement that the catalyst be sufficiently active to allow minute amounts of catalyst to yield large quantities of polymer, it must also give predominantly polypropylene with high tacticity that is, a highly ordered molecular stmcture with high crystallinity. The three stmctures for polypropylene are the isotactic, syndiotactic, and atactic forms (90) (see Olefin polya rs, polypropylene). 

Crystallinity is low the pendent allyl group contributes to the amorphous state of these polymers. Propylene oxide homopolymer itself has not been developed commercially because it cannot be cross-baked by current methods (18). The copolymerization of PO with unsaturated epoxide monomers gives vulcanizable products (19,20). In ECH—PO—AGE, poly(ptopylene oxide- o-epichlorohydrin- o-abyl glycidyl ether) [25213-15-4] (5), and PO—AGE, poly(propylene oxide-i o-abyl glycidyl ether) [25104-27-2] (6), the molar composition of PO ranges from approximately 65 to 90%. 

Type 3A sieves. A crystalline potassium aluminosilicate with a pore size of about 3 Angstroms. This type of molecular sieves is suitable for drying liquids such as acetone, acetonitrile, methanol, ethanol and 2-propanol, and drying gases such as acetylene, carbon dioxide, ammonia, propylene and butadiene. The material is supplied as beads or pellets. 

The minimum service temperature is determined primarily by the Tg of the soft phase component. Thus the SBS materials ctm be used down towards the Tg of the polybutadiene phase, approaching -100°C. Where polyethers have been used as the soft phase in polyurethane, polyamide or polyester, the soft phase Tg is about -60°C, whilst the polyester polyurethanes will typically be limited to a minimum temperature of about 0°C. The thermoplastic polyolefin rubbers, using ethylene-propylene materials for the soft phase, have similar minimum temperatures to the polyether-based polymers. Such minimum temperatures can also be affected by the presence of plasticisers, including mineral oils, and by resins if these become incorporated into the soft phase. It should, perhaps, be added that if the polymer component of the soft phase was crystallisable, then the higher would also affect the minimum service temperature, this depending on the level of crystallinity. 

The two structures appear very similar. Poly( 1,2-propylene adipate) has the same basic structure as poly(ethylene adipate), except for a pendant methyl group. This pendant methyl group on the poly( 1,2-propylene adipate) makes a large difference, however. Poly( 1,2-propylene adipate) has no crystalline melting point. Trappe theorizes that the pendant methyl prevents chain packing and therefore, prevents crystallization [42]. 

The next major commodity plastic worth discussing is polypropylene. Polypropylene is a thermoplastic, crystalline resin. Its production technology is based on Ziegler s discovery in 1953 of metal alkyl-transition metal halide olefin polymerization catalysts. These are heterogeneous coordination systems that produce resin by stereo specific polymerization of propylene. Stereoregular polymers characteristically have monomeric units arranged in orderly periodic steric configuration. 

Polyethylene and polypropylene are semitransparent plastics made by polymerization. They are produced from ethylene and propylene in a variety of grades. Their mechanical properties are determined mainly by density (degree of crystallinity) and molecular weight, characterized by the Melt Index (MI). 

TPEs from blends of rubber and plastics constitute an important category of TPEs. These can be prepared either by the melt mixing of plastics and rubbers in an internal mixer or by solvent casting from a suitable solvent. The commonly used plastics and rubbers include polypropylene (PP), polyethylene (PE), polystyrene (PS), nylon, ethylene propylene diene monomer rubber (EPDM), natural rubber (NR), butyl rubber, nitrile rubber, etc. TPEs from blends of rubbers and plastics have certain typical advantages over the other TPEs. In this case, the required properties can easily be achieved by the proper selection of rubbers and plastics and by the proper change in their ratios. The overall performance of the resultant TPEs can be improved by changing the phase structure and crystallinity of plastics and also by the proper incorporation of suitable fillers, crosslinkers, and interfacial agents. 

Whereas the electrochemical decomposition of propylene carbonate (PC) on graphite electrodes at potentials between 1 and 0.8 V vs. Li/Li was already reported in 1970 [140], it took about four years to find out that this reaction is accompanied by a partially reversible electrochemical intercalation of solvated lithium ions, Li (solv)y, into the graphite host [64], In general, the intercalation of Li (and other alkali-metal) ions from electrolytes with organic donor solvents into fairly crystalline graphitic carbons quite often yields solvated (ternary) lithiated graphites, Li r(solv)yC 1 (Fig. 8) [7,24,26,65,66,141-146],... 

Extensive studies of stereoselective polymerization of epoxides were carried out by Tsuruta et al.21 s. Copolymerization of a racemic mixture of propylene oxide with a diethylzinc-methanol catalyst yielded a crystalline polymer, which was resolved into optically active polymers216 217. Asymmetric selective polymerization of d-propylene oxide from a racemic mixture occurs with asymmetric catalysts such as diethyzinc- (+) bomeol218. This reaction is explained by the asymmetric adsorption of monomers onto the enantiomorphic catalyst site219. Furukawa220 compared the selectivities of asymmetric catalysts composed of diethylzinc amino acid combinations and attributed the selectivity to the bulkiness of the substituents in the amino acid. With propylene sulfide, excellent asymmetric selective polymerization was observed with a catalyst consisting of diethylzinc and a tertiary-butyl substituted a-glycol221,222. ... 

---