Crude atmospheric distillation unit

Atmospheric distillation separates the crude oil complex mixture into different fractions with relatively narrow boiling ranges. In general, separation of a mixture into fractions is based primarily on the difference in the boiling points of the components. In atmospheric distillation units, one or more fractionating columns are used. 

By approaching the refinery design from a crude oil perspective, the advantage of preseparation by stepwise condensation after HTFT synthesis was reduced. The refinery design included primary separation steps typically found in crude oil refineries, namely, an atmospheric distillation unit (ADU) that is followed by a vacuum distillation unit (VDU). Despite the design intent, the operation of these units, out of necessity, had to be different. The reboiler temperature of the ADU was... 

The fractions obtained by vacuum distillation of the reduced crude (atmospheric residuum) from an atmospheric distillation unit depend on whether or not the unit is designed to produce lubricating or vacuum gas oils. In the former case, the fractions include (1) heavy gas oil, which is an overhead product and is used as catalytic cracking stock or, after suitable treatment, a light lubricating oil (2) lubricating oil (usually three fractions—light, intermediate, and heavy), which is obtained as a side-stream product and (3) asphalt (or residuum), which is the nonvolatile product and may be used directly as, or to produce, asphalt, and which may also be blended with gas oils to produce a heavy fuel oil. 

Case study crude oil atmospheric distillation unit... 

The current oil sands bitumen upgrading processes for the production of synthetic crude oil (Table 4) begin with diluted bitumen being processed through the diluent recovery units. The diluent recovery units are atmospheric distillation units that serve three purposes 1) distill off diluent naphtha and return it to the froth treatment process 2) distill off light gas oil and send it directly to a light gas oil hydrotreater and 3) produce hot atmospheric topped bitumen as feedstock for vacuum distillation unit and downstream bitumen conversion processes. 

Specialised units are used to simulate complex fractionation processes in petroleum refining. Typical configuration consists of a main column with pump-around and side strippers (Fig. 3.14). Among applications, we may cite pre-flash tower, crude atmospheric distillation, or Fluid Catalytic Cracking (FCC) main fractionator. 

The first step in the building the atmospheric distillation unit is entering the composition of the crude in order to generate the necessary hypothetical components for model. For the purposes of this simulation, we will consider the crude assays given in Table 2.5 to Table 2.8. It is important to remember that that we may have to remove extraneous details from the distillation curve to avoid unusual column behavior. We use the TB P distillation, density distribution and overall bulk density to define this system in Figure 2.14. 

A combination unit is a special type of unit that was developed to reduce the investment for a small refinery. In effect, one main distillation unit serves as a crude fi-actionator as well as the cat unit primary fractionator. This same tower also serves the naphtha reformer and visbreaker. A schematic diagram of a combination unit is shown in Figure 2. Crude oil is topped (material boiling below 650°F is removed) in the atmospheric tower, and the topped crude is sent to the combination tower along with cat products and naphtha reformer products. These latter streams provide heat to distill the topped crude and also, being more volatile than topped crude, provide a lifting effect which assists in vaporizing more of the crude. 

The atmospheric reduced crude is the feedstock for the vacuum distillation unit. To prevent thermal decomposition (cracking) of the higher boiling point hydrocarbons in the crude oil, the pressure in the vacuum distillation fractionation column is reduced to about one-twentieth of an atmosphere absolute (one atmosphere pressure is 14.7 psia or 760 mm Fig). This effectively reduces the boiling points of the hydrocarbons several hundred degrees Fahrenheit. The components boiling below about 1050°F (565°C) are vaporized and removed as vacuum gas... 

Kerosine, a distillate fraction heavier than naphtha, is normally a product from distilling crude oils under atmospheric pressures. It may also he obtained as a product from thermal and catalytic cracking or hydrocracking units. Kerosines from cracking units are usually less stable than those produced from atmospheric distillation and hydrocracking units due to presence of variable amounts of olefinic constituents. 

Gas oil is a heavier petroleum fraction than kerosine. It can be obtained from the atmospheric distillation of crude oils (atmospheric gas oil, AGO), from vacuum distillation of topped crudes (vacuum gas oil, VGO), or from cracking and hydrocracking units. 

Several thousand compounds are present in petroleum. Few are separated as pure substances. Many of the uses of petroleum can be served by certain fractions from the distillation of crude oil. Typical distillation fractions and their uses are given in Table 7.3 and a distillation unit is shown in Fig. 7.5. The complexity of the molecules, molecular weight, and carbon number increase with the boiling point. The higher boiling fractions are usually distilled in vacuo at lower temperature than their atmospheric boiling points to avoid excessive decomposition to tars. 

Well over 50 large-scale EO model-based RTO applications have been deployed for petroleum refining processes. These model applications have been deployed in petroleum refineries Liporace et al., 2009 Camolesi et al., 2008 Mudt et al., 1995, both on separation units (crude atmospheric and vacuum distillation units) and on reactor units (including fluidized catalytic crackers (FCC), gasoline reformers, and hydrocrackers). 

Atmospheric distillation is least effective in converting heavier products into lighter components. A second distillation column under vacuum is needed to further separate the heavier parts of crude oil into lighter fractions. Some fractions from the vacuum units have better quality than atmospheric distillation cuts because the metal-bearing compounds and carbon-forming materials are concentrated in the vacuum residue. 

F3 - Atmospheric Residue from Crude Distillation Unit 2 (AR-CDU2)... 

In atmospheric or straight-run distillation the crude oil is first pumped into the fractional distillation unit. This is the refinery s tallest unit and some of its columns are used for atmospheric distillation while others are for vacuum distillation. Heated to about 680°F in the gas furnaces, the petroleum reaches the first atmospheric column, which is divided into compartments for fractional distillation. The lighter and more volatile hydrocarbons rise to the upper part. Those that are heavier and less volatile collect in the lower part. While rising, a volatile mass tends to shed its less volatile elements. 

Jet fuel is kerosene-based aviation fuel. It is medium distillate used for aviation turbine power units and usually has the same distillation characteristics and flash point as kerosene. Jet fuels are manufactured predominately from straight-run kerosene or kerosene-naphtha blends in the case of wide cut fuels that are produced from the atmospheric distillation of crude oil. Jet fuels are similar in gross composition, with many of the differences in them attributable to additives designed to control some fuel parameters such as freeze and pour point characteristics. For example, the chromatogram (Figure 27.4) of a commercial jet fuel (Jet A) is dominated by GC-resolved n-alkanes in a narrow range of n-C-j to n-Cig with maximum being around n-Ci. The UCM is well dehned. 

---