Corrosion impedance spectroscopy

AC impedance spectroscopy is widely employed for the investigation of both solid- and liquid-phase phenomena. In particular, it has developed into a powerfiil tool m corrosion teclmology and in the study of porous electrodes for batteries [, and ]. Its usage has grown to include applications ranging from... 

Other techniques to detennine the corrosion rate use instead of DC biasing, an AC approach (electrochemical impedance spectroscopy). From the impedance spectra, the polarization resistance (R ) of the system can be detennined. The polarization resistance is indirectly proportional to j. An advantage of an AC method is given by the fact that a small AC amplitude applied to a sample at the corrosion potential essentially does not remove the system from equilibrium. 

Electrochemical Impedance Spectroscopy (EIS) and AC Impedance Many direct-current test techniques assess the overall corrosion process occurring at a metal surface, but treat the metal/ solution interface as if it were a pure resistor. Problems of accuracy and reproducibility frequently encountered in the application of direct-current methods have led to increasing use of electrochemical impedance spectroscopy (EIS). 

Although the above experiments involved exposure to the environment of unbonded surfaees, the same proeess oeeurs for buried interfaces within an adhesive bond. This was first demonstrated by using electrochemical impedance spectroscopy (EIS) on an adhesive-covered FPL aluminum adherend immersed in hot water for several months [46]. EIS, which is commonly used to study paint degradation and substrate corrosion [47,48], showed absorption of moisture by the epoxy adhesive and subsequent hydration of the underlying aluminum oxide after 100 days (Fig. 10). After 175 days, aluminum hydroxide had erupted through the adhesive. 

Impedance spectroscopy This technique is essentially the extension of polarization resistance measurements into low-conductivity environments, including those listed above. The technique can also be used to monitor atmospheric corrosion, corrosion under thin films of condensed liquid and the breakdown of protective paint coatings. Additionally, the method provides mechanistic data concerning the corrosion processes, which are taking place. 

The capacitance. The electrical double layer may be regarded as a resistance and capacitance in parallel see Section 20.1), and measurements of the electrical impedance by the imposition of an alternating potential of known frequency can provide information on the nature of a surface. Electrochemical impedance spectroscopy is now well established as a powerful technique for investigating electrochemical and corrosion systems. 

Papakonstantinou, P., Zhao, J. F., Richardot, A., McAdams, E. T., and McLaughlin, J. A., Evaluation of Corrosion Performance of Ultra-thin Si-DLC Overcoats with Electrochemical Impedance Spectroscopy, Diamond Relat. Mater, Vol. 11,... 

ENA was recently used for remote on-line corrosion monitoring of carbon steel electrodes in a test loop of a surge water tank at a gas storage field. An experimental design and system for remote ENA and collection of electrochemical impedance spectroscopy (EIS) data (Fig. 13) have been presented elsewhere. In the gas storage field, noise measurements were compared with electrode weight loss measurements. Noise resistance (R ) was defined as... 

Electrochemical impedance spectroscopy techniques record impedance data as a function of the frequency of an applied signal at a fixed potential. A large frequency range (65 kHz-1 mHz) must be investigated to obtain a complete impedance spectrum. Dowling et al. and Franklin et al. demonstrated that the small signals required for EIS do not adversely affect the numbers, viability, and activity of microorganisms within a biofilm. EIS data may be used to determine the inverse of the corrosion... 

Electrochemical impedance spectroscopy, AC probes. EIS, although around since the 1960s, has primarily been a laboratory technique. Commercially available probes and monitoring systems that measure EIS are becoming more widely used, especially in plants that have on-staff corrosion experts to interpret the data or to train plant personnel to do so. 

Electrochemical impedance, weight loss, and potentiodyne techniques can be used to determine the corrosion rates of carbon steel and the activities of both sulfate-reducing bacteria and acid-producing bacteria in a water injection field test. A study revealed that the corrosion rates determined by the potentiodyne technique did not correlate with the bacterial activity, but those obtained by electrochemical impedance spectroscopy (EIS) were comparable with the rates obtained by weight loss measurements [545]. 

Electrochemical techniques have been utilized for many years to study metal corrosion. Two of these techniques, linear polarization (LP) and cyclic voltammetry (CV), complement each other, LP providing corrosion rates under conditions where the surface is minimally altered and CV furnishing information about the corrosion mechanism. With the advent of impedance spectroscopy (IS), both kinds of information can be gleaned simultaneously and more rapidly, while leaving the surface almost intact. In this paper, we discuss the application of IS to the study of rapid steel corrosion and describe a study we undertook to elucidate the roles played by adsorption and film formation in the inhibition mechanisms of the above-named compounds. For comparison, we also investigated two quaternary nitrogen salts, which appear to adsorb electrostatically and presumably do not form macroscopic films (8). 

The impedance spectroscopy of steel corrosion in concentrated HC1, with and without inhibitors, exhibit relatively straightforward electrochemical phenomenology and can be represented by simple equivalent circuits involving primarily passive electrical elements. Analysis of these circuits for steel corroding in HC1 per se reveals that the heterogeneity of the surface is established rapidly and can be simulated with a simple electrical circuit model. 

Electrochemical impedance spectroscopy was used to determine the effect of isomers of 2,5-bis( -pyridyl)-l,3,4-thiadiazole 36 (n 2 or 3) on the corrosion of mild steel in perchloric acid solution <2002MI197>. The inhibition efficiency was structure dependent and the 3-pyridyl gave better inhibition than the 2-pyridyl. X-ray photoelectron spectroscopy helped establish the 3-pyridyl thiadiazoles mode of action toward corrosion. Adsorption of the 3-pyridyl on the mild steel surface in 1M HCIO4 follows the Langmuir adsorption isotherm model and the surface analysis showed corrosion inhibition by the 3-pyridyl derivative is due to the formation of chemisorbed film on the steel surface. 

Owing to its extraordinary chemical stability, diamond is a prospective electrode material for use in theoretical and applied electrochemistry. In this work studies performed during the last decade on boron-doped diamond electrochemistry are reviewed. Depending on the doping level, diamond exhibits properties either of a superwide-gap semiconductor or a semimetal. In the first case, electrochemical, photoelectrochemical and impedance-spectroscopy studies make the determination of properties of the semiconductor diamond possible. Among them are the resistivity, the acceptor concentration, the minority carrier diffusion length, the flat-band potential, electron phototransition energies, etc. In the second case, the metal-like diamond appears to be a corrosion-stable electrode that is efficient in the electrosyntheses (e.g., in the electroreduction of hard to reduce compounds) and electroanalysis. Kinetic characteristics of many outer-sphere... 

Wallinder et al. examined passivation of 316L using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization, and x-ray photoelectron spectroscopy (XPS) techniques to examine the relationships between corrosion resistance and surface chemistry after passivation treatments (17). The... 

Admittance measurements were used extensively prior to the widespread use of impedance spectroscopy in the 1980s. Capacitance bridge methods are typically used, though this limits the lower bound on the measured frequency to several hundred hertz. Corrosion processes, whose time constants are normally measured at or below 1 Hz, cannot be directly interrogated with this method. 

In this experiment, corrosion rates will be estimated via the Stern-Geary relationship by measuring the polarization resistance, Rp. This parameter will be measured in two ways via conventional polarization resistance (PR) measurements and via electrochemical impedance spectroscopy (EIS). In addition, the errors in corrosion rate estimation introduced by the use of a finite scan rate and the presence of uncompensated ohmic resistance will be demonstrated. 

Electrochemical impedance spectroscopy (EIS) is a powerful tool for examining the processes occurring at the electrode surfaces. EIS is a kind of electrochemical analysis method which can be used in the characterization of batteries, fuel cells, and corrosion phenomena. 

P.R. Roberge and V.S. Sastri, Electrochemical Impedance Spectroscopy as a Reliable and Powerful Technique for Olnine Corrosion Monitoring , Paper No. 396, CORROSION 93. 

EIS data extrapolation, uses neural networks to train on electrochemical impedance spectroscopy data for extrapolation Filter debris analysis (FDA) expert system, condition monitoring of aircrafts GENERA, generic problem-solving framework for characterizing corrosion and materials problems LipuCor, prediction of corrosion in oil and gas systems... 

One of the most important applications of neural network methodology is in the extrapolation of electrochemical impedance data obtained in corrosion studies.34 Electrochemical impedance spectroscopy (EIS) can be used to obtain instantaneous corrosion rates. The validation of extension of EIS data frequency range, which is conventionally difficult, can be done using a neural network system. In addition to extension of impedance data frequency range, the neural network identifies problems such as the inherent variability of corrosion data and provides solutions to the problems. Furthermore, noisy or poor-quality data are dealt with by neural works through the output of the parameters variance and confidence.33... 

The traditional way is to measure the impedance curve, Z(co), point-after-point, i.e., by measuring the response to each individual sinusoidal perturbation with a frequency, to. Recently, nonconventional approaches to measure the impedance function, Z(a>), have been developed based on the simultaneous imposition of a set of various sinusoidal harmonics, or noise, or a small-amplitude potential step etc, with subsequent Fourier- and Laplace transform data analysis. The self-consistency of the measured spectra is tested with the use of the Kramers-Kronig transformations [iii, iv] whose violation testifies in favor of a non-steady state character of the studied system (e.g., in corrosion). An alternative development is in the area of impedance spectroscopy for nonstationary systems in which the properties of the system change with time. 

Potentiodynamictechniques— are all those techniques in which a time-dependent -> potential is applied to an - electrode and the current response is measured. They form the largest and most important group of techniques used for fundamental electrochemical studies (see -> electrochemistry), -> corrosion studies, and in -> electroanalysis, -+ battery research, etc. See also the following special potentiodynamic techniques - AC voltammetry, - DC voltammetry, -> cyclic voltammetry, - linear scan voltammetry, -> polarography, -> pulse voltammetry, - reverse pulse voltammetry, -> differential pulse voltammetry, -> potentiodynamic electrochemical impedance spectroscopy, Jaradaic rectification voltammetry, - square-wave voltammetry. 

The similar breakdown of the surface state was also observed with parylene C film. Parylene C is a semicrystalline polymer and one of the most effective barriers for gases and vapors according to permeability values. It was thought that such an excellent barrier film would provide superior corrosion protection of a metal when it was deposited on the metal surface. Contrary to the expectation, parylene C film didn t provide good corrosion protection due to the surface state breakdown described above. This conclusion was ascertained by studies using electrochemical impedance spectroscopy (EIS), which is described in Chapter 28. 

Electrochemical impedance spectroscopy (EIS) is a valuable method with which to study the barrier property and corrosion protection performance of polymer-coated metals it has been widely used in this field in recent years [11-15]. Many examples can be found in the literature, which illustrate the performance deterioration of different coatings on metals as well as pretreatment effects on the properties of... 

---