Corrosion study

The mechanisms of lead corrosion in sulfuric acid have been studied and good reviews of the Hterature are available (27—30). The main techniques used in lead corrosion studies have been electrochemical measurements, x-ray diffraction, and electron microscopy. More recendy, laser Raman spectroscopy and photoelectrochemistry have been used to gain new insight into the corrosion process (30,31). 

Development of practical and low cost separators has been an active area of ceU development. CeU separators must be compatible with molten lithium, restricting the choice to ceramic materials. Early work employed boron nitride [10043-11-5] BN, but a more desirable separator has been developed using magnesium oxide [1309-48-4], MgO, or a composite ofMgO powder—BN fibers. Corrosion studies have shown that low carbon steel or... 

Very often the environment is reflected in the composition of corrosion products, eg, the composition of the green patina formed on copper roofs over a period of years. The determination of the chemical composition of this green patina was one of the first systematic corrosion studies ever made (see Copper). The composition varied considerably depending on the location of the stmcture as shown in Table 2 (26,27). 

Probably the most serious disadvantage of this method of corrosion study is the assumed average-time weight loss. The corrosion rate could be high initially and then decrease with time (it could fall to zero). In other cases the rate of corrosion might increase veiy gradually with time or it could cycle or be some combination of these things. 

Zinc is often used as a protective coating over iron to form galvanized iron. In industrial settings exposed to SOj and humidity, this zinc coating is subject to sufficient corrosion to destroy its protective capacity. Haynie and Upham (5) used their results from a zinc corrosion study to predict the useful life of a zinc-coated galvanized sheet in different environmental settings. Table 9-2 shows the predicted useful life as a function of SO concentration. 

Uhlig, H. H. and Gilman, 3. R., Inhibition of Pitting Corrosion of Stainless Steel 18/8 in Iron(III) Chloride Solutions by Nitrates , Z. Physik. Chem.,21/6, 127 (1964) C.A., 61,9231c Fisher, W. R., Pitting Corrosion, Especially of Titanium. 1 Corrosion Studies , Techn. Mill. 

Moberg, L. E. Long-term Corrosion Studies In Vitro of Gold, Cobalt-Chromium and Nickel-Chromium Alloys in Contact Acta Odontologia Scandanavia, 43, 215-222 (1985)... 

The successful clinical use of titanium and cobalt-chromium alloy combinations has been reported Lucas etal. also investigated this combination using electrochemical studies based on mixed potential and protection potential theories. Verification of these studies was made by direct coupling experiments. The electrochemical studies predicted coupled corrosion potentials of -0.22 V and low coupled corrosion rates of 0.02 ft A/cm. Direct coupling experiments verified these results. The cobalt-titanium interfaces on the implants were macroscopically examined and no instances of extensive corrosion were found. Overall, the in-vitro corrosion studies and the examination of retrieved prostheses predicted no exaggerated in-vivo corrosion due to the coupling of these cobalt and titanium alloys. 

Hanawalt, Nelson, Peloubet Corrosion Studies of Magnesium and its Alloys , Trans Am. Inst. Mining Met. Eng. 147, 273-299 (1942)... 

Most of the controlled corrosion studies on beryllium have been carried out in the USA in simulated reactor coolants. The latter have usually been water, aerated and de-aerated, containing small amounts of hydrogen peroxide and at temperatures up to 300-350°C. Many variables have been examined, covering surface condition, chemical composition, temperature, pH, galvanic effects and mechanical stress . 

The hardness of such coatings may reach a maximum of about 400 Hy as compared with approximately 50 Hy for a soft gold deposit. A series of corrosion studies in industrial and marine atmospheres by Baker" has indicated that the protective value of hard gold coatings is comparable with that of the pure metal, and that a thickness of only 0-002 5 mm gives good protection to copper base alloys during exposure for six months. 

Corrosion tests provide the basis for the practical control of corrosion and therefore deserve a more exhaustive discussion than limitations of space will permit. A detailed description of all the procedures and devices that have been employed in corrosion studies in many countries will not be attempted. Instead, attention will be directed principally to underlying principles and to comments on the significance and limitations of the results of the test methods that are considered. Further details may be obtained from the references and from the comprehensive works by Champion and Ailor ... 

Instruments very suitable for corrosion work are readily available, with several different models produced commercially. Although most, if not all, of the available potentiostats are properly designed, it should be kept in mind that corrosion studies require the instrument to have a low internal resistance and to react quickly to changes of potential of the working electrode. 

We conclude this review with an example of the application of SPFM to corrosion studies. Atmospheric chemical corrosion constitutes a severe threat to the structural integrity of... 

Fotouhi B, Katty A, Gorochov O (1985) Photoelectrochemical and corrosion study of n-type SnSSe. J Electrochem Soc 132 2181-2184... 

Iron and Stainless Steel. The purpose of XPS investigations on typical corrosion systems like iron or stainless steel, is the determination of the composition of the passive surface layer, if possible, as a function of depth. As a consequence of the technical and economic relevance of corrosion reactions, XPS investigations on corrosion systems are numerous. With respect to the application of XPS, there is no difference between corrosion systems and any other electrochemical surface reaction like oxide formation on noble metals. Therefore, in this paragraph only a few recent typical results of such studies, using XPS, will be mentioned. For a detailed collection of XPS corrosion studies the reader is referred to references [43,104], A review of aqueous corrosion studies, using XPS, was given by McIntyre for the elements O, Cr, Mn, Fe, Co, Ni, Cu and Mo [105], The book edited by M. Froment [111] gives an impression of the research achieved on passivity of metals up to 1983. 

Copper Corrosion Study. F. Romero, California State University—Dominguez Hills, http //tardis.csudh.edu/fromero/chemistry/copper/index.html... 

Michie, T., 1988, Oil and Gas Industry Water Injection Well Corrosion Study In Proceedings of the UIPC Summer Meetings, pp. 47-67. 

A feature of corrosion studies which has been stressed recently (2) is the complete failure of laboratory tests on their own to predict how reliable operation of some nuclear steam generators can be maintained. At least a part of this problem is likely to arise from different redox and/or pH conditions imposed by the solution in autoclave tests and in plant conditions and many low level contaminants could be involved. In view of what has been said earlier concerning the role of Mo(VI) in stagnant water it is clear that some data, at least on the thermodynamics of aqueous Mo species, should be sought at high temperatures. 

---