Computer interfacing

IEEE standard 488-1978 interface represents a highly flexible, moderate-speed system that is well suited to general laboratory use. The IEEE-488 interface bus (IB) consists of 16 signal lines. Eight lines are used for data, five for bus management, and three lines are used to establish a temporary communication link, or handshake, between two devices that are properly attached to the bus. Because there are eight data lines, an 8-bit byte can be communicated in each handshake cycle. Thus 16-bit, 24-bit, etc. words (either instructions or data) can be communicated with sequential handshake cycles. This method is often referred to as bit parallel, byte serial transmission (Colloms [1983]). 

The IEEE-488 IB is designed to interface with the four major types of devices shown in Eigure 3.1.21. A master or controller sends commands over the bus, using the bus control (uniline) and data lines (mnltiline). Normally, one controller is present (e.g. a computer or microprocessor), but if more are present, only one may exercise control at any time. A controller issnes a system initiation command, interface clear (IFC), and designates which devices are talkers and which are listeners. The controller has complete control of the attention line (ATN). When ATN is true, the controller is issuing messages or commands. 

A listener receives data over the IB, following an acceptor handshake. Addressed listeners respond to controller commands. Listen-only devices are intended for use in a circuit with no controller. An example of a listener might be a digitally controlled analog potentiostat. 

A talker is a device capable of sending data over the IB to a controller or listener. An unaddressed talk-only device, such as a digital voltmeter, may represent a problem in a circuit wim a controller, since mis device may continue talking when the controller requires attention (ATN true ), resulting in a garbled message. 

Most commercial devices intended for use wim an IEEE-488 IB are combined talker-listeners, capable of receiving instructions, settmg me data collection mode and experimental conditions, and returning data to me controller. 

---

In another type of measurement, the parallel between mechanical and electrical networks can be exploited by using variable capacitors and resistors to balance the impedance of the transducer circuit. These electrical measurements readily lend themselves to computer interfacing for data acquisition and analysis. 

Most of the experimental information concerning copolymer microstructure has been obtained by physical methods based on modern instrumental methods. Techniques such as ultraviolet (UV), visible, and infrared (IR) spectroscopy, NMR spectroscopy, and mass spectroscopy have all been used to good advantage in this type of research. Advances in instrumentation and computer interfacing combine to make these physical methods particularly suitable to answer the question we pose With what frequency do particular sequences of repeat units occur in a copolymer. 

Figure 4.8 shows a specific example of this type of diagram which includes some symbols. The diagram shows the tasks that the operator and the computer must perform in a computer controlled reactor. The central column is used to show any functional requirements of the human-computer interface. 

They can be used for solving resource allocation problems, looking at aspects of time-stress, and designing the human computer interface. 

Gilmore, W. E., Gertman, D. I., Blackman, H. S. (1989), User-Computer Interface in Process Control—A Human Factors Engineering Handbook. New York Academic Press. 

Schematic of a typical EMCS with local control modules, command control modules, and personal computer interface.

Personal computer interface simplifies operator control of the system through a user-friendly interface. 

Command modules communicate with other modules through a local area network (LAN). Through this LAN, command modules receive information from the local control modules and store data. These data can be stored from a week to two years, depending on the recording interval and the number of points to be monitored. Unlike host-based systems, which use a central computer to interrogate each command module individually, the computer interface can tap into the network like any other command module. 

The personal computer interface allows for easy operation of an EMCS, but all of the system s control... 

The DAC system consisted of computer, interface cards, meters, transmitters, and solid state relays (SSR). Electrodes of pH (Ingold), Oxidation-Reduction Potential (Cole-Parmer), and Dissolved Oxygen (Ingold) were installed and connected to individual meter. The status of reactor and the value of electrode signal were displayed in a computer monitor, and stored in data file. 

These high-profile developments were accompanied by improvements in technology such as electronics, particularly the advent of transistors and integrated circuit boards, fiber optics, and computer interfaces. 

Part 4 1984 Specification for basic symbols for process computer, interface and shared display/control functions. 

GW Martyn, Jr. The people computer interface in a capsule molding operation. Drug Dev Comm 1 39, 1974-5. 

The computer interface system lends itself well to the determination of interfacial tension and contact angles using Equation 3 and the technique described by Pike and Thakkar for Wilhelmy plate type experiments (20). Contact angles for crude oil/brine systems using the dynamic Wilhelmy plate technique have been determined by this technique and all three of the wetting cycles described above have been observed in various crude oil/brine systems (21) (Teeters, D. Wilson, J. F. Andersen, M. A. Thomas, D. C. J. Colloid Interface Sci., 1988, 126, in press). The dynamic Wilhelmy plate device also addresses other aspects of wetting behavior pertinent to petroleum reservoirs. 

FIGURE 6.12 (a) Image of clinic- and field-usable, computer-interfaced, skin carotenoid RRS instrument,... 

The computer age has brought about considerable innovation in the operation of laboratory instrumentation. One consequence of this is the wider acceptance and utilization of the optical microscope as a quantitative analytical instrument. A brief literature survey illustrates the diversity of disciplines and optical methods associated with the development of computer interfaced optical microscopy. This is followed by a description of how our methods of fluorescence, interferometry and stereology, nsed for characterizing polymeric foams, have incorporated computers. 

User-friendly computer interfaces and work stations that do not require considerable amounts of technical background to run the instrument... 

Chemists use computers for many purposes. As the previous sections on instrumental methods have illustrated, every modem analytical instrument must include a computer interface. Chemical structure drawing, visualization, and modeling programs are important computer-supported applications required in academic, industrial, and governmental educational and research enterprises. Computational chemistry has allowed practicing chemists to predict molecular structures of known and theoretical compounds and to design and test new compounds on computers rather than at the laboratory bench. 

The RSST apparatus can be operated with its own controller or with a computer interface. Heating rates depend on the Cp of the reactive sample, and can be varied from 0.25°C/min to approximately 2°C/min. Isothermal experiments can also be run. The contents of the test cell can be mixed with a... 

Adult subject studies can be divided into two broad categories response to basic sensory stimulation and response to more complex cognitive tasks. Recently, there have also been reports applying the NIR spectroscopy to brain computer interface research [18] and studyinh the correlation of hemodynamic response to computational cognitive models [94]. 

S. Coyle, T. Ward, C. Markham, and G. McDarby. On the suitability of near-infrared (nir) systems for next-generation brain-computer interfaces. Physiological Measurement, 25 815-822, 2004. 

In the last few years, the number of ENDOR publications on systems of biological interest has remarkably increased, indicating that the advantages offered by this technique have been realized by many research groups. It should not be concealed, however, that in this type of compounds poor sensitivity may cause serious problems, so that large samples and (or) computer interfacing capabilities have usually to be available. 

The scan rate of the potential is usually in the range from 0.020 V s-1 to 100 V s"1. Until a few years ago the resulting current-potential curves were recorded with a normal X-Y recorder up to a scan rate of about 0.5 V s-1 for higher scan rates it was necessary to use an oscilloscope. Recently, however, the use of personal computers interfaced with the electrochemical apparatus has overcome most recording problems. 

Fluorometers designed for research purposes(31) are typically equipped with a xenon arc lamp, monochromators, one or more photomultiplier tubes, cuvet holders, and a computer interface. Some research level fluorometers, such as the Perkin-Elmer LS50, have optional microtiter plate reading accessories with fiber optic bundles. This is convenient since 96-well microtiter plates are commonly used for immunoassay development, and many commercial immunoassays are based on the use of microtiter plates. Fluorometers designed for commercial immunoassay purposes are generally dedicated instruments with few, if any, data acquisition and reduction parameters that can be manipulated by the user. 

---