Combined classifications

This classifier [30] combines classification with particle size analysis. The material is fed into the elassifying chamber with the aid of a special feeder and injector at rates between 40 and 60 g min. At the outlet of the... 

Alkyd resins are usually referred to by a shorthand description based on a certain way of classification or a combined classification, from which the general properties... 

More frequently, alkyd resins are described by a combined classification in terms of their oil length, the type of fatty acids, and any unusual ingredients. Such descriptions as an isophthalic, very long tall oil alkyd or a medium oil dehydrated castor-PE (the PE refers to pentaerythritol, not polyethylene) alkyd or a short oil lauric-benzoic alkyd would immediately project the general properties of the resin. 

Hybrid systems. Depending on the problem to be solved, use can also be made of a combination of techniques leading to a hybrid system. For example, a rule-based system may use neural networks for solving classification subproblems (as is described in [Hopgood, 1993]), or a combination of a rule-based and a CBR system can be used as in the system for URS data interpretation described later in this paper. 

It is very important to make classification of dynamic models and choose an appropriate one to provide similarity between model behavior and real characteristics of the material. The following general classification of the models is proposed for consideration deterministic, stochastic or their combination, linear, nonlinear, stationary or non-stationary, ergodic or non-ergodic. 

The combination of contrast and granularity produces a signal to noise ratio which allows for direct comparison of various films. The classes have minimum values for eontrast and maximum values for graininess. The ASTM classification system employs the same parameters as the European Standard EN584-1 and ISO CD (see Table 1). 

Manual ultrasonic testing offers the advantages of low equipment cost combined with the flexibility of the human operator to provide good access and complex scanning capability. However, a total reliance on the capabilities of the ultrasonic technician to visualise the physical situation leads to a number of drawbacks, including lack of accuracy and consistency of defect size and location measurements, lack of verification that the required scan coverage has been fully achieved, and lack of consistency in flaw classification. A further disadvantage is that the ultrasonic data is not permanently recorded there is therefore no opportunity for the data to be re-examined at a later date if required. 

Figure C2.2.7. Schematic illustrating tire classification and nomenclature of discotic liquid crystal phases. For tire columnar phases, tire subscripts are usually used in combination witli each otlier. For example, denotes a rectangular lattice of columns in which tire molecules are stacked in a disordered manner (after [33])...

A more general classification considers the phase of the total electronic wave function [13]. We have treated the case of cyclic polyenes in detail [28,48,49] and showed that for Hiickel systems the ground state may be considered as the combination of two Kekule structures. If the number of electron pairs in the system is odd, the ground state is the in-phase combination, and the system is aromatic. If the number of electron pairs is even (as in cyclobutadiene, pentalene, etc.), the ground state is the out-of-phase combination, and the system is antiaromatic. These ideas are in line with previous work on specific systems [40,50]. 

As the number of conformations increases exponentially with the number of rotatable bonds, for most molecules it is not feasible to take all possible conformations into account. However, a balanced sampling of the conformational space should be ensured if only subsets arc being considered. In order to restrict the number of geometries output, while retaining a maximum of conformational diversity, ROTATE offers the possibility of classifying the remaining conformations, i.c., similar conformations can be combined into classes. The classification is based on the RMS deviation between the conformations, either in Cartesian (RMS y 7if [A]) or torsion space in [ ], The RMS threshold, which decides whether two... 

Since 1970 a variety of reaction classification schemes have been developed to allow a more systematic processing of the huge variety of chemical reaction instances (see Chapter III, Section 1 in the Handbook). Reaction classification serves to combine several reaction instances into one reaction type. In this way, the vast number of observed chemical reactions is reduced to a manageable number of reaction types. Apphcation to specific starting materials of the bond and electron changes inherent in such a reaction type then generates a specific reaction instance. 

The nomenclature of cellular polymers is not standardized classifications have been made according to the properties of the base polymer (22), the methods of manufacture, the cellular stmcture, or some combination of these. The most comprehensive classification of cellular plastics, proposed in 1958 (23), has not been adopted and is not consistent with some of the common names for the more important commercial products. 

Searching of one or more on-line databases is a technique increasingly used ia novelty studies. The use of such databases enables the searcher to combine indexing parameters, including national and international classifications natural language words ia the full text of patents, ia their claims, or ia abstracts suppHed by iaventor and by professional documentation services and indexing systems of various sorts. Because the various patent databases have strengths and weaknesses that complement each other, the use of multiple databases is thus pmdent, and is faciUtated by multifile and cross-file techniques provided by the various on-line hosts. 

A classification by chemical type is given ia Table 1. It does not attempt to be either rigorous or complete. Clearly, some materials could appear ia more than one of these classifications, eg, polyethylene waxes [9002-88 ] can be classified ia both synthetic waxes and polyolefins, and fiuorosihcones ia sihcones and fiuoropolymers. The broad classes of release materials available are given ia the chemical class column, the principal types ia the chemical subdivision column, and one or two important selections ia the specific examples column. Many commercial products are difficult to place ia any classification scheme. Some are of proprietary composition and many are mixtures. For example, metallic soaps are often used ia combination with hydrocarbon waxes to produce finely dispersed suspensions. Many products also contain formulating aids such as solvents, emulsifiers, and biocides. 

Gas-phase separations may be classified as enrichment, sharp, or purification separation, depending on the purity, recovery, and magnitude of the pertinent separation. The classification system allows for a certain amount of synergy, as several separation methods may be combined in order to achieve the desired result. Certain separation methods ate favored for each category (26). 

The basis of all bulk conveyor engineering is the precise definition and accurate classification of materials according to individual characteristics under a specific combination of handling conditions (1). Since the late 1960s there has been an extraordinary growth in research into the fundamental properties and behavior of particulate soHds. However, as of this writing, it is not possible to predict the handling behavior of a bulk soHds material relevant to conditions in a specific conveyor, merely on the basis of the discrete particle properties. 

An unknown commercial detergent may contain some combination of anionic, nonionic, cationic, and possibly amphoteric surfactants, inorganic builders and fillers as weU as some minor additives. In general, the analytical scheme iacludes separation of nonsurfactant and inorganic components from the total mixture, classification of the surfactants, separation of iadividual surfactants, and quantitative determination (131). 

The concern of the government is to prevent tax-free industrial ethanol from finding its way into beverages. To achieve this end, the regulations call for a combination of financial and adininistrative controls (bonds, permits, and scmpulous record keeping) and chemical controls (denaturants that make the ethanol unpalatable). Regulations estabUsh four distinct classifications of industrial ethanol. The classifications with the most stringent financial and adininistrative controls call for Httle or no chemical denaturants. The classifications that call for the most effective chemical denaturants require the least financial and administrative controls. For a Hst of denaturants currently authorized, see Reference 284. 

Commercial dryers differ fundamentally by the methods of heat transfer employed (see classification of diyers, Fig. 12-45). These industrial-diyer operations may utihze heat transfer by convection, conduction, radiation, or a combination of these. In each case, however, heat must flow to the outer surface and then into the interior of the solid. The single exception is dielectric and microwave diying, in which high-frequency electricity generates heat internally and produces a high temperature within the material and on its surface. 

In kaohn classification, the product is typically measured with a certain percentage less than a given size (example 90 percent or 95 percent less than 1 or 2 lm). Each combination of percent and size cut represents a condition by which the centiifuge would have to tune to yield the product specification. 

Size Reduction Combined with Size Classification. 20-16... 

Size Reduction Combined with Size Classification Grinding systems are batch or continuous in operation (Fig. 20-11). Most large-scale operations are continuous batch ball or pebble mills are used... 

Ball mills or tube mills can be operated in closed circuit with external air classifiers with or without air sweeping being employed. If air sweeping is employed, a cyclone separator may Be placed between mill and classifier. (The principles of size reduction combined with size classification are discussea under Characteristics of Size Classifiers. ) Likewise other types of grinding mill can be operated in closed circmt with external size classifiers (Fig. 20-12), as will be described at appropriate places on succeeding pages. However, many types of grinders are air-swept and are so closely coupled with their classifiers mat the latter are termed internal classifiers. 

High-speed hammer or pin mills result in some selective grinding. Such mills combined with air classification can produce fractions with controlled protein content. An example of such a combination is a Bauer hurricane hammer mill combined with the Alpine Mikroplex superfine classifier. Flour with different protein content is needed for... 

---