Sensitivity activation analysis

Figure 13.2 Table of activation analysis sensitivities as offered by General Atomic Company, San Diego, California.

Methods for iodine deterrnination in foods using colorimetry (95,96), ion-selective electrodes (94,97), micro acid digestion methods (98), and gas chromatography (99) suffer some limitations such as potential interferences, possibHity of contamination, and loss during analysis. More recendy neutron activation analysis, which is probably the most sensitive analytical technique for determining iodine, has also been used (100—102). 

Instiximental neutron activation analysis (INAA) is considered the most informative and highly sensitive. Being applied, it allows detecting and determination of 30-40 elements with the sensitivity of 10 -10 g/g in one sample. The evident advantage of INAA is the ability to analyze samples of different nature (filters, soils, plants, biological tests, etc.) without any complex schemes of preliminai y prepai ation. 

Atomic absorption spectroscopy of VPD solutions (VPD-AAS) and instrumental neutron activation analysis (INAA) offer similar detection limits for metallic impurities with silicon substrates. The main advantage of TXRF, compared to VPD-AAS, is its multielement capability AAS is a sequential technique that requires a specific lamp to detect each element. Furthermore, the problem of blank values is of little importance with TXRF because no handling of the analytical solution is involved. On the other hand, adequately sensitive detection of sodium is possible only by using VPD-AAS. INAA is basically a bulk analysis technique, while TXRF is sensitive only to the surface. In addition, TXRF is fast, with an typical analysis time of 1000 s turn-around times for INAA are on the order of weeks. Gallium arsenide surfaces can be analyzed neither by AAS nor by INAA. 

A modem technique for nitrogen detn is known as fast neutron activation analysis. Materials such as RDX are exposed to a high density fast neutron flux which converts the 14N content of the sample into unstable 13N. The N is detd by measuring the 13 N produced by the 14N (n, 2n) 13N reaction. This technique is extremely sensitive, but requires specialized instrumentation (Refs 44, 51 61)... 

This can result in a radioactive product from the A(n, t)A reaction where A is the stable element, n is a thermal neutron, A is the radioactive product of one atomic mass unit greater than A, and y is the prompt gamma ray resulting from the reaction. A is usually a beta and/or gamma emitter of reasonably long half-life. Where access to a nuclear reactor has been convenient, thermal neutron activation analysis has proven to be an extremely valuable nondestructive analytical tool and in many cases, the only method for performing specific analyses at high sensitivities... 

This section will deal briefly with some aspects of expls safety peculiar to neutron activation analysis expts. We are concerned here with a) the possible effect of the ionizing radiation dose on the energetic material which will cause it to be more sensitive or hazardous to normal handling as an expl, and b) the potential direct expl hazards involved in the physical and mechanical transportation of samples to and horn the irradiation source and in a nuclear counting system... 

Activation analysis is based on a principle different from that of other analytical techniques, and is subject to other types of systematic error. Although other analytical techniques can compete with NAA in terms of sensitivity, selectivity, and multi-element capability, its potential for blank-free, matrix-independent multielement determination makes it an excellent reference technique. NAA has been used for validation of XRF and TXRF. 

Highly sensitive determination of "Tc is possible using today s advanced mass spectroscopic methods. However, orthodox determination methods of "Tc involving radiometric techniques or even activation analysis are still used because they are simple and can be done without expensive machines. The detection limits of typical analytical methods are listed in Table 1. 

Calcium-selective electrodes have long been in use for the estimation of calcium concentrations - early applications included their use in complexometric titrations, especially of calcium in the presence of magnesium (42). Subsequently they have found use in a variety of systems, particularly for determining stability constants. Examples include determinations for ligands such as chloride, nitrate, acetate, and malonate (mal) (43), several diazacrown ethers (44,45), and methyl aldofuranosides (46). Other applications have included the estimation of Ca2+ levels in blood plasma (47) and in human hair (where the results compared satisfactorily with those from neutron activation analysis) (48). Ion-selective electrodes based on carboxylic polyether ionophores are mentioned in Section IV.B below. Though calcium-selective electrodes are convenient they are not particularly sensitive, and have slow response times. 

To date, a few methods have been proposed for direct determination of trace iodide in seawater. The first involved the use of neutron activation analysis (NAA) [86], where iodide in seawater was concentrated by strongly basic anion-exchange column, eluted by sodium nitrate, and precipitated as palladium iodide. The second involved the use of automated electrochemical procedures [90] iodide was electrochemically oxidised to iodine and was concentrated on a carbon wool electrode. After removal of interference ions, the iodine was eluted with ascorbic acid and was determined by a polished Ag3SI electrode. The third method involved the use of cathodic stripping square wave voltammetry [92] (See Sect. 2.16.3). Iodine reacts with mercury in a one-electron process, and the sensitivity is increased remarkably by the addition of Triton X. The three methods have detection limits of 0.7 (250 ml seawater), 0.1 (50 ml), and 0.02 pg/l (10 ml), respectively, and could be applied to almost all the samples. However, NAA is not generally employed. The second electrochemical method uses an automated system but is a special apparatus just for determination of iodide. The first and third methods are time-consuming. 

Although the neutron activation analysis is inherently more sensitive than the atomic absorption spectrometry, both procedures yield a reliable measurement of vanadium in seawater at the natural levels of concentration. 

Table 10.2 Sensitivity of neutron activation analysis in determination of elements by (n,...

Neutron activation analysis is an attractive method in many trace element problems, or where the total amount of sample is limited. Many geochemical studies of trace constituents and semi-conductor developments have used the technique, whilst in recent years pollution investigations have provided a new focus. In forensic science small flakes of paint, single hairs and a variety of other small samples have been analysed and identified by activation analysis. In recent years activation analysis has lost further ground to ICP-MS which provides more comprehensive information and is more readily operated. Sensitivity is also comparable in many cases. 

It was not until the application of neutron activation analysis (NAA) that the problem of overlapping sources could be tackled. NAA is a highly sensitive and essentially non-destructive technique, although samples have to be taken which remain radioactive for some time after analysis. The use of NAA in characterizing obsidian was first demonstrated in the early 1970s (Aspinall... 

The number of protons is unique to the element but most elements can exist with two or more different numbers of neutrons in their nucleus, giving rise to different isotopes of the same element. Some isotopes are stable, but some (numerically the majority) have nuclei which change spontaneously - that is, they are radioactive. Following the discovery of naturally radioactive isotopes around 1900 (see Section 10.3) it was soon found that many elements could be artificially induced to become radioactive by irradiating with neutrons (activation analysis). This observation led to the development of a precise and sensitive method for chemical analysis. 

Until it was known that the half-life of Tc is much shorter than 10 years Herr looked for technetiimi-98 in a munber of minerals from Norway and South Africa by neutron activation analysis. This most sensitive method was also used by Alperovitch et al. and Anders et al. to detect this isotope in nature. According to the nuclear reaction... 

A method has been developed for the determination of technetium-99 in mixed fission products by neutron activation analysis Tc is separated from most fission products by a cyclohexanone extraction from carbonate solution, the stripping into water by addition of CCI4 to the cylohexanone phase, and the adsorption on an anion exchange column. Induced Tc radioactivity is determined using X-ray spectrometry to measure the 540 and 591 keV lines. The sensitivity of the analysis under these conditions is approximately 5 ng. The method has been successfully applied to reactor fuel solutions. 

Some of the methods commonly used for the determination of thorium in biological materials are given in Table 6-1. The colorimetric methods are not capable of isotope-specific determination of thorium isotopes. Alpha spectrometric and neutron activation analysis are useful in the quantification of isotope-specific thorium and thorium-232, respectively, and have better sensitivities than colorimetric methods. Alpha spectrometry is the commonly used isotope-specific analysis for the determination of thorium-232 and the thorium-230 derived from the decay of uranium-238 (Wrenn et al. 1981). Standard reference materials (SRMs) containing thorium in human liver (SRM-4352) and human lung (SRM-4351) necessary for the determination of absolute recovery in a given sample are available from the National Institute of Standards and Technology (Inn 1987). 

Gold may be identified by its physical properties. Trace quantities of gold may be analyzed by flame atomic absorption spectrophotometry (to 1 ppm) or by neutron activation analysis (to 1 ppb). The metal may be dissolved in aqua regia and the solution diluted appropriately prior to analysis. The most sensitive wavelength for this element is 242.8nm. 

Rhodium may be analyzed by flame atomic absorption spectrophotometry using the direct air-acetylene flame method. The metal, its oxide and insoluble salts may be solubilized by digesting with sulfuric acid—hydrochloric acid mixture. Rhodium also may by analyzed by ICP-AES and ICP/MS techniques. ICP/MS is the most sensitive method. Also, it may be analyzed by neutron activation analysis. 

---