Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Vinylpyridin

Several studies have concerned the microstnicture of lamellae in materials such as the block copolymers polystyrene-h/oc/r-poly-l-vinylpyridine [139] and polystyrene-h/oc/r-polybutadiene [140], as well as single crystals of poly-para-xylylene [139], and reveal features (such as intersecting lamellae (figure Bl.19.29)) that had not been previously observed. [Pg.1705]

Indoles can also be alkylated by conjugate addition under alkaline conditions. Under acidic conditions, alkylation normally occurs at C3 (see Section 11.1). Table 9.1 includes examples of alkylation by ethyl acrylate, acrylonitrile, acrylamide and 4-vinylpyridine. [Pg.91]

Copolymerization can be carried out with styrene, acetonitrile, vinyl chloride, methyl acrylate, vinylpyridines, 2-vinylfurans, and so forth. The addition of 2-substituted thiazoles to different dienes or mixtures of dienes with other vinyl compounds often increases the rate of polymeriza tion and improves the tensile strength and the rate of cure of the final polymers. This allows vulcanization at lower temperature, or with reduced amounts of accelerators and vulcanizing agents. [Pg.398]

Strauss and Williamst have studied coil dimensions of derivatives of poly(4-vinylpyridine) by light-scattering and viscosity measurements. The derivatives studied were poly(pyridinium) ions quaternized y% with n-dodecyl groups and (1 - y)% with ethyl groups. Experimental coil dimensions extrapolated to 0 conditions and expressed relative to the length of a freely rotating repeat unit are presented here for the molecules in two different environments ... [Pg.70]

Resin and Polymer Solvent. Dimethylacetamide is an exceUent solvent for synthetic and natural resins. It readily dissolves vinyl polymers, acrylates, ceUulose derivatives, styrene polymers, and linear polyesters. Because of its high polarity, DMAC has been found particularly useful as a solvent for polyacrylonitrile, its copolymers, and interpolymers. Copolymers containing at least 85% acrylonitrile dissolve ia DMAC to form solutions suitable for the production of films and yams (9). DMAC is reportedly an exceUent solvent for the copolymers of acrylonitrile and vinyl formate (10), vinylpyridine (11), or aUyl glycidyl ether (12). [Pg.85]

A number of methods such as ultrasonics (137), radiation (138), and chemical techniques (139—141), including the use of polymer radicals, polymer ions, and organometaUic initiators, have been used to prepare acrylonitrile block copolymers (142). Block comonomers include styrene, methyl acrylate, methyl methacrylate, vinyl chloride, vinyl acetate, 4-vinylpyridine, acryUc acid, and -butyl isocyanate. [Pg.197]

AlkyUithium compounds are primarily used as initiators for polymerizations of styrenes and dienes (52). These initiators are too reactive for alkyl methacrylates and vinylpyridines. / -ButyUithium [109-72-8] is used commercially to initiate anionic homopolymerization and copolymerization of butadiene, isoprene, and styrene with linear and branched stmctures. Because of the high degree of association (hexameric), -butyIUthium-initiated polymerizations are often effected at elevated temperatures (>50° C) to increase the rate of initiation relative to propagation and thus to obtain polymers with narrower molecular weight distributions (53). Hydrocarbon solutions of this initiator are quite stable at room temperature for extended periods of time the rate of decomposition per month is 0.06% at 20°C (39). [Pg.239]

Molecular weights of polymers that function as bridging agents between particles are ca 10 —10. Ionic copolymers of acrylamide are the most significant commercially (see Acrylamide POLYMERS). Cationic comonomers include (2-methacryloyloxyethyl)trimethylammonium salts, diethyl aminoethyl methacrylate [105-16-8], and dimethyldiallylammonium chloride [7398-69-8], anionic comonomers include acryUc acid [79-10-7] and its salts. Both types of polyacrylamides, but especially the anionic, can be more effective in the presence of alum (10,11). Polyetbylenimine and vinylpyridine polymers, eg, po1y(1,2-dimethy1-5-viny1pyridiniiim methyl sulfa te) [27056-62-8] are effective but are used less frequentiy. [Pg.15]

Tire Cord. Melamine resins are also used to improve the adhesion of mbber to reinforcing cord in tires. Textile cord is normally coated with a latex dip solution composed of a vinylpyridine—styrene—butadiene latex mbber containing resorcinol—formaldehyde resin.. The dip coat is cured prior to use. The dip coat improves the adhesion of the textile cord to mbber. Further improvement in adhesion is provided by adding resorcinol and hexa(methoxymethyl) melamine [3089-11 -0] (HMMM) to the mbber compound which is in contact with the textile cord. The HMMM resin and resorcinol cross-link during mbber vulcanization and cure to form an interpenetrating polymer within the mbber matrix which strengthens or reinforces the mbber and increases adhesion to the textile cord. Brass-coated steel cord is also widely used in tires for reinforcement. Steel belts and bead wire are common apphcations. Again, HMMM resins and resorcinol [108-46-3] are used in the mbber compound which is in contact with the steel cord to reinforce the mbber and increase the adhesion of the mbber to the steel cord. This use of melamine resins is described in the patent Hterature (49). [Pg.331]

An industrially important example is the condensation of a- (2) or y-picoline (4) with aqueous formaldehyde to form the corresponding ethanolpyridines, 2-ethanolpyridine [104-74-2] (22) and 4-ethanolpyridine [5344-27-4] respectively, followed by dehydration of the alcohols to give 2- (23) or 4-vinylpyridine. [Pg.326]

Vinylpyridine (23) came into prominence around 1950 as a component of latex. Butadiene and styrene monomers were used with (23) to make a terpolymer that bonded fabric cords to the mbber matrix of automobile tires (25). More recendy, the abiUty of (23) to act as a Michael acceptor has been exploited in a synthesis of 4-dimethylaminopyridine (DMAP) (24) (26). The sequence consists of a Michael addition of (23) to 4-cyanopyridine (15), replacement of the 4-cyano substituent by dimethylamine (taking advantage of the activation of the cyano group by quatemization of the pyridine ring), and base-cataly2ed dequatemization (retro Michael addition). 4-r)imethyl aminopyri dine is one of the most effective acylation catalysts known (27). [Pg.326]

The relative production volumes of pyridine compounds can be ranked in the following order pyridine (1) > P-picoline (3) > a-picoline (2)> niacin (27) or niacinamide (26)> 2-vinylpyridine (23)> piperidine (18). U.S. and Japanese production was consumed internally as well as being exported, mainly to Europe. European production is mosdy consumed internally. Growth in production of total pyridine bases is expected to be small through the year 2000. [Pg.333]

Shipment Methods and Packaging. Pyridine (1) and pyridine compounds can be shipped in bulk containers such as tank cars, rail cars, and super-sacks, or in smaller containers like fiber or steel dmms. The appropriate U.S. Department of Transportation (DOT) requirements for labeling are given in Table 4. Certain temperature-sensitive pyridines, such as 2-vinylpyridine (23) and 4-vinylpyridine are shipped cold (<—10°C) to inhibit polymerisation. Piperidine (18) and certain piperidine salts are regulated within the United States by the Dmg Enforcement Agency (DEA) (77). Pyridines subject to facile oxidation, like those containing aldehyde and carbinol functionaUty, can be shipped under an inert atmosphere. [Pg.333]

Most of them are generally classified as poisons. Exceptions to this rule are known. A notable one is 4-dimethyl aminopyridine (DMAP) (24), which is widely used in industry as a superior acylation catalyst (27). Quaternary salts of pyridines are usually toxic, and in particular paraquat (20) exposure can have fatal consequences. Some chloropyridines, especially polychlorinated ones, should be handled with extra care because of their potential mutagenic effects. Vinylpyridines are corrosive to the skin, and can act as a sensitizer for some susceptible individuals. Niacin (27), niacinamide (26), and some pyridinecarbaldehydes can cause skin flushing. [Pg.335]

The primary use of a-picoline (2) is as a precursor of 2-vinylpyridine (23). It is also used in a variety of agrochemicals and pharmaceuticals, such as nitrapyrin [1929-82-4] (60) to prevent loss of ammonia from fertilizers picloram [1918-02-1] (61), a herbicide and amproHum [121 -25-5] (62), a coccidiostat. [Pg.335]

The main use of y-picoline (4) is in the production of the antituberculosis agent, isonia2id (31). Compound (4) is also used to make 4-vinylpyridine, and subsequendy polymers. [Pg.336]

Ethanolpyridines are used mainly for vinylpyridine manufacture. However, 2-ethanolpyridine (22) is used to make the psychotropic agent thioridazine [50-52-2] (106), and the antispasmodic agent triquizium bromide [71731-58-3] (107). [Pg.340]

Synthetic. The main types of elastomeric polymers commercially available in latex form from emulsion polymerization are butadiene—styrene, butadiene—acrylonitrile, and chloroprene (neoprene). There are also a number of specialty latices that contain polymers that are basically variations of the above polymers, eg, those to which a third monomer has been added to provide a polymer that performs a specific function. The most important of these are products that contain either a basic, eg, vinylpyridine, or an acidic monomer, eg, methacrylic acid. These latices are specifically designed for tire cord solutioning, papercoating, and carpet back-sizing. [Pg.253]

The Time-Zero film process has an efficient receiving layer consisting of a graft copolymer of 4-vinylpyridine and a vinylhenzyltrimethylammonium salt grafted to hydroxyethylceUulose (81,82). The accuracy of color rendition was improved in the Time-Zero SX-70 film by the use of the xanthene magenta dye-developer (1). [Pg.501]


See other pages where Vinylpyridin is mentioned: [Pg.313]    [Pg.421]    [Pg.90]    [Pg.410]    [Pg.488]    [Pg.488]    [Pg.581]    [Pg.899]    [Pg.899]    [Pg.630]    [Pg.799]    [Pg.1055]    [Pg.1055]    [Pg.1055]    [Pg.1055]    [Pg.1055]    [Pg.1055]    [Pg.207]    [Pg.197]    [Pg.151]    [Pg.528]    [Pg.333]    [Pg.333]    [Pg.334]    [Pg.334]    [Pg.334]    [Pg.341]    [Pg.341]    [Pg.256]    [Pg.260]    [Pg.136]    [Pg.465]   


SEARCH



4-Vinylpyridine

Vinylpyridines

© 2024 chempedia.info