Hydrocarbon solutes

Sundstrdm V and Gillbro T 1985 Dynamics of trans-cis photoisomerization of stiibene in hydrocarbon solutions Ber. Bunsenges Phys. Chem. 89 222-6... 

Anionic polymerization of vinyl monomers can be effected with a variety of organometaUic compounds alkyllithium compounds are the most useful class (1,33—35). A variety of simple alkyllithium compounds are available commercially. Most simple alkyllithium compounds are soluble in hydrocarbon solvents such as hexane and cyclohexane and they can be prepared by reaction of the corresponding alkyl chlorides with lithium metal. Methyllithium [917-54-4] and phenyllithium [591-51-5] are available in diethyl ether and cyclohexane—ether solutions, respectively, because they are not soluble in hydrocarbon solvents vinyllithium [917-57-7] and allyllithium [3052-45-7] are also insoluble in hydrocarbon solutions and can only be prepared in ether solutions (38,39). Hydrocarbon-soluble alkyllithium initiators are used directiy to initiate polymerization of styrene and diene monomers quantitatively one unique aspect of hthium-based initiators in hydrocarbon solution is that elastomeric polydienes with high 1,4-microstmcture are obtained (1,24,33—37). Certain alkyllithium compounds can be purified by recrystallization (ethyllithium), sublimation (ethyllithium, /-butyUithium [594-19-4] isopropyllithium [2417-93-8] or distillation (j -butyUithium) (40,41). Unfortunately, / -butyUithium is noncrystaUine and too high boiling to be purified by distiUation (38). Since methyllithium and phenyllithium are crystalline soUds which are insoluble in hydrocarbon solution, they can be precipitated into these solutions and then redissolved in appropriate polar solvents (42,43). OrganometaUic compounds of other alkaU metals are insoluble in hydrocarbon solution and possess negligible vapor pressures as expected for salt-like compounds. 

AlkyUithium compounds are primarily used as initiators for polymerizations of styrenes and dienes (52). These initiators are too reactive for alkyl methacrylates and vinylpyridines. / -ButyUithium [109-72-8] is used commercially to initiate anionic homopolymerization and copolymerization of butadiene, isoprene, and styrene with linear and branched stmctures. Because of the high degree of association (hexameric), -butyIUthium-initiated polymerizations are often effected at elevated temperatures (>50° C) to increase the rate of initiation relative to propagation and thus to obtain polymers with narrower molecular weight distributions (53). Hydrocarbon solutions of this initiator are quite stable at room temperature for extended periods of time the rate of decomposition per month is 0.06% at 20°C (39). 

GopolymeriZation Initiators. The copolymerization of styrene and dienes in hydrocarbon solution with alkyUithium initiators produces a tapered block copolymer stmcture because of the large differences in monomer reactivity ratios for styrene (r < 0.1) and dienes (r > 10) (1,33,34). In order to obtain random copolymers of styrene and dienes, it is necessary to either add small amounts of a Lewis base such as tetrahydrofuran or an alkaU metal alkoxide (MtOR, where Mt = Na, K, Rb, or Cs). In contrast to Lewis bases which promote formation of undesirable vinyl microstmcture in diene polymerizations (57), the addition of small amounts of an alkaU metal alkoxide such as potassium amyloxide ([ROK]/[Li] = 0.08) is sufficient to promote random copolymerization of styrene and diene without producing significant increases in the amount of vinyl microstmcture (58,59). 

The methodology for preparation of hydrocarbon-soluble, dilithium initiators is generally based on the reaction of an aromatic divinyl precursor with two moles of butyUithium. Unfortunately, because of the tendency of organ olithium chain ends in hydrocarbon solution to associate and form electron-deficient dimeric, tetrameric, or hexameric aggregates (see Table 2) (33,38,44,67), attempts to prepare dilithium initiators in hydrocarbon media have generally resulted in the formation of insoluble, three-dimensionally associated species (34,66,68—72). These precipitates are not effective initiators because of their heterogeneous initiation reactions with monomers which tend to result in broader molecular weight distributions > 1.1)... 

Enhanced Oil Recovery. A hydrocarbon solution of TYZOR TPT, TYZOR TBT, or TYZOR TOT can be pumped into the porous zones of an oil-bearing formation upon contact with water, an amorphous, gelatinous plug is formed, which allows water to be diverted to less porous... 

Halobutyls. Chloro- and bromobutyls are commercially the most important butyl mbber derivatives. The halogenation reaction is carried out in hydrocarbon solution using elemental chlorine or bromine (equimolar ratio with enchained isoprene). The halogenation is fast, and proceeds mainly by an ionic mechanism. The stmctures that may form include the following ... 

Halogenated Butyl Rubber. The halogenation is carried out in hydrocarbon solution using elemental chlorine or bromine in a 1 1 molar ratio with enchained isoprene. The reactions ate fast chlorination is faster. Both chlorinated and brominated butyl mbbers can be produced in the same plant in blocked operation. However, there are some differences in equipment and reaction conditions. A longer reaction time is requited for hromination. Separate faciUties are needed to store and meter individual halogens to the reactor. Additional faciUties are requited because of the complexity of stabilising brominated butyl mbber. 

Dicaproyl peroxide Dicyclohexyl perdicarbonate Di-2-ethylhexyl perdicarbonate (40% hydrocarbon solution)... 

At about 159°C it turns pink and adopts the sandwich structure, expected for [M(C5H5)2] compounds, and this is retained in the gaseous phase and in hydrocarbon solutions. Using substituted cyclopentadienyls a variety of analagous sandwich compounds have been prepared and their magnetic properties indicate that the... 

The same approach supposedly demonstrated the dimeric nature of lithium polyisoprene and polybutadiene. A tenfold decrease of viscosity was claimed 97), contrary to the findings of Worsfold and By water 115) who reported a 15 fold decrease of viscosity for lithium polyisoprene on protonation of their hydrocarbon solutions. 

Finally it should be stressed that the complexation affects the microstructure of poly dienes. As was shown by Langer I56) small amounts of diamines added to hydrocarbon solutions of polymerizing lithium polydienes modify their structure from mainly 1,4 to a high percentage of vinyl unsaturation, e.g., for an equivalent amount of TMEDA at 0 °C 157) the fraction of the vinyl amounts to about 80%. Even more effective is 1,2-dipiperidinoethane, DIPIP. It produces close to 100% of vinyl units when added in equimolar amount to lithium in a polymerization of butadiene carried out at 5 °C 158 159), but it is slightly less effective in the polymerization of isoprene 160>. 

Kinetic Mechanism, The following ionic mechanism describes sytrene polymerization in a hydrocarbon solution with n-butyllithiiam as the initiator (1-6), ... 

Di-n-butyl perdicarbonate (25% hydrocarbon solution) 2 4-Dichlorobenzoyl peroxide (50% phthalate solution)... 

Dimethyl peroxide Diethyl peroxide Di-t-butyl-di-peroxyphthalate Difuroyl peroxide Dibenzoyl peroxide Dimeric ethylidene peroxide Dimeric acetone peroxide Dimeric cyclohexanone peroxide Diozonide of phorone Dimethyl ketone peroxide Ethyl hydroperoxide Ethylene ozonide Hydroxymethyl methyl peroxide Hydroxymethyl hydroperoxide 1-Hydroxyethyl ethyl peroxide 1 -Hydroperoxy-1 -acetoxycyclodecan-6-one Isopropyl percarbonate Isopropyl hydroperoxide Methyl ethyl ketone peroxide Methyl hydroperoxide Methyl ethyl peroxide Monoperoxy succinic acid Nonanoyl peroxide (75% hydrocarbon solution) 1-Naphthoyl peroxide Oxalic acid ester of t-butyl hydroperoxide Ozonide of maleic anhydride Phenylhydrazone hydroperoxide Polymeric butadiene peroxide Polymeric isoprene peroxide Polymeric dimethylbutadiene peroxide Polymeric peroxides of methacrylic acid esters and styrene... 

Trends of solubility enhancement for each diamondoid follow regular behavior like other heavy hydrocarbon solutes in supercritical solvents with respect to variations in pressure and density [38, 39]. Supercritical solubilities of... 

R. M. Kowalik, I. Duvdevani, K. Kitano, and D. N. Schulz. Drag reduction agents for hydrocarbon solutions. Patent US 4625745,1986. 

Sham, T.-K. X-Ray Absorption Studies of Liquids Structure and Reactivity of Metal Complexes in Solution and X-Ray Photoconductivity of Hydrocarbon Solutions of Organometallics, 145, 81-106(1987). 

This compound was found, on investigation of an explosion in a syringe during transfer, to have a decomposition energy equivalent to that of commercial explosives. Slow decomposition, even at room temperature, becomes explosive above 100°C. Shock sensitive. Stable as hydrocarbon solution below 25% concentration. Recommended that this and related compounds be handled only in such solution. See FLUORINATED ORGANOLITHIUM COMPOUND... 

Pqq - 1 atm) with various concentrations of cosolvents added led to significant quenching of by donor solvents and gave linear Stern-Volmer type plots (e.g., f°/ f versus [THF]) with slopes (KSy) of 34 1, 26 1 and 16 1 M 1 for THF, diglyme and cyclohexene, respectively. In contrast, photolysis in 2,5-dimethyltetrahydrofuran led to quantum yields comparable to those observed in hydrocarbon solutions, an observation which reinforces the view that the ability to coordinate may be important to the quenching process. 

---