Test stand testing

Bench or test stand testing Testing of a pressure relief device on a test stand using an external pressure source with or without an auxiliary lift device, to determine some or all of its operating characteristics, without necessarily flowing the rated capacity. This is required on a regular basis when the valve is taken into the maintenance cycle (see Chapter 10) at least to see that there is no shift on the set pressure and that the valve would open correctly during a pressure upset. 

The acronym "CIAPES" stands for - Controle et Inspection des Appareils a pression lors de I Epreuve et en Service (Control and Inspection of Pressure Vessels during Testing and in Service). 

Under testing conditions the fuel element to be tested is placed at the stand. Then it is moved into the control unit and gripped with a collet. First the density distribution of the vibro-compacted fuel along the total length of the fuel element is tested. Proceeding from the obtained data the section to be investigated in detail is chosen and a tomogramm of this section is obtained. 

In Eq. (14) "est stands for the calculated (estimated) response, exp" for the experimental one, and n and m are the numbers of objects in the training set and the test set respectively. CoSE stands for Compound Standard Error. As an option, one can employ several test sets, if needed. 

Place I g. of benzamide and 15 ml. of 10% aqueous sodium hydroxide solution in a 100 ml. conical flask fitted with a reflux water-condenser, and boil the mixture gently for 30 minutes, during which period ammonia is freely evolved. Now cool the solution in ice-water, and add concentrated hydrochloric acid until the mixture is strongly acid. Benzoic acid immediately separates. Allow the mixture to stand in the ice-water for a few minutes, and then filter off the benzoic add at the pump, wash with cold water, and drain. Recrystallise from hot water. The benzoic acid is obtained as colourless crystals, m.p. 121°, almost insoluble in cold water yield, o 8 g. (almost theoretical). Confirm the identity of the benzoic acid by the tests given on p. 347. 

Sulphur. THE LASSAIGNE SODIUM TEST. The sodium fusion will have converted any sulphur present in the original compounds to sodium sulphide. Dissolve a few crystals of sodium nitroprusside, Na8[Fe(CN)5NO],zH20, in water, and add the solution to the third portion of the filtrate obtained from the sodium fusion. A brilliant purple coloration (resembling permanganate) indicates sulphur the coloration slowly fades on standing. Note, (i) Sodium nitroprusside is unstable in aqueous solution and therefore the solution should be freshly prepared on each occasion, (ii) This is a very delicate test for sulphides, and it is essential therefore that all apparatus, particularly test-tubes, should be quite clean. 

Special Tests (i) Nitro-prusside + NaOH (red). (ii) Iodoform Nitroprusside + NaOH (red) (1) NaHSOs, immediate ppt. (i) FeCls (violet) (ii) NaHSOj, ppt. on standing. 

Place about 0 2 g. of jack-bean meal in a test-tube, add 2 ml. of water and about 5 drops of phenol-red. Mix thoroughly and allow the faintly yellow solution to stand while the urea solution is being made up. 

To 1 ml. of the alcohol in a small test-tube, add quickly 6 ml. of Lucas reagent at 26-27°, close the tube with a cork, shake, and allow to stand. Observe the mixture during 5 minutes. The following results may be obtained —... 

For alcohols of b.p. below 150°, mix 0- 5 g. of 3-nitrophthalic anhydride (Section VII,19) and 0-5 ml. (0-4 g.) of the dry alcohol in a test-tube fitted with a short condenser, and heat under reflux for 10 minutes after the mixture liquefies. For alcohols boiling above 150°, use the same quantities of reactants, add 5 ml. of dry toluene, heat under reflux until all the anhydride has dissolved and then for 20 minutes more remove the toluene under reduced pressure (suction with water pump). The reaction product usually solidifies upon cooling, particularly upon rubbing with a glass rod and standing. If it does not crystallise, extract it with dilute sodium bicarbonate solution, wash the extract with ether, and acidify. Recrystallise from hot water, or from 30 to 40 per cent, ethanol or from toluene. It may be noted that the m.p. of 3-nitrophthalic acid is 218°. 

NHjCONHNHj.HCl) and 1-5 g. of crystallised sodium acetate in 10 ml. of water in a test-tube. Add 1 ml. of acetone, close the tube with a cork and shake vigorously. Allow the mixtme to stand, with occasional vigorous shaking, for 10 minutes it is advantageous to cool in ice. FUter the crystals, wash with a httle cold water, and recrystaUise from water or dilute alcohol. The m.p. of acetone semicarbazone is 187°. 

Hydrolysis (or saponification) of n-butyl acetate. Boil 4-5 g. of n-butyl acetate (Section 111,95) with 50 ml. of 10 per cent, sodium hydroxide solution under reflux until the odour of the ester can no longer be detected (about 1 hour). Set the condenser for downward distiUation and coUect the first 10 ml. of distillate. Saturate it with potassium carbonate, aUow to stand for 5 minutes, and withdraw all the Uquid into a small pipette or dropper pipette. AUow the lower layer of carbonate solution to run slowly into a test-tube, and place the upper layer into a small test-tube or weighing bottle. Dry the alcohol with about one quarter of its buUr of anhydrous potassium carbonate. Remove the alcohol with a dropper pipette and divide it into two parts use one portion for the determination of the b.p. by the Siwoloboff method (Section 11,12) and convert the other portion into the 3 5-dinitrobenzoate (Section III, 27) and determine the m.p. 

Method 1. Place in a test-tube or small flask 1-3 g. of glycerol and 30 ml. of 10 per cent, sodium hydroxide solution add gradually, with simultaneous shaking, 1-2 g. of benzoyl chloride. Stopper the vessel, shake for several minutes and allow to stand. Decant the solution from the pasty solid and wash the latter with cold water by decantation. Recrystallise the solid tribenzoate from dilute rectified (or methylated) spirit or from light petroleum, b.p. 40-60° the pure compound has m.p. 76°. 

It is advisable to test a small portion of the filtrate for platinum by acidifying with hydrochloric acid and adding a few drops of stannous chloride solution a yellow or brown colour develops according to the quantity of platinum pVesent. The yellow colour is soluble in ether, thus rendering the t t more sensitive. If platinum is found, treat the filtrate with excess of formaldehyde and sodium iQrdroxide solution and heat,- platinum black septarates on standing and may be filtered and worked up with other platinum residues (see Method 3). 

Add 25 g. of finely-powdered, dry acetanilide to 25 ml. of glacial acetic acid contained in a 500 ml. beaker introduce into the well-stirred mixture 92 g. (50 ml.) of concentrated sulphuric acid. The mixture becomes warm and a clear solution results. Surround the beaker with a freezing mixture of ice and salt, and stir the solution mechanically. Support a separatory funnel, containing a cold mixture of 15 -5 g. (11 ml.) of concentrated nitric acid and 12 -5 g. (7 ml.) of concentrated sulphuric acid, over the beaker. When the temperature of the solution falls to 0-2°, run in the acid mixture gradually while the temperature is maintained below 10°. After all the mixed acid has been added, remove the beaker from the freezing mixture, and allow it to stand at room temperature for 1 hour. Pour the reaction mixture on to 250 g. of crushed ice (or into 500 ml. of cold water), whereby the crude nitroacetanilide is at once precipitated. Allow to stand for 15 minutes, filter with suction on a Buchner funnel, wash it thoroughly with cold water until free from acids (test the wash water), and drain well. Recrystallise the pale yellow product from alcohol or methylated spirit (see Section IV,12 for experimental details), filter at the pump, wash with a httle cold alcohol, and dry in the air upon filter paper. [The yellow o-nitroacetanihde remains in the filtrate.] The yield of p-nitroacetanihde, a colourless crystalline sohd of m.p. 214°, is 20 g. 

In a 500 ml. bolt-head flask, provided with a mechanical stirrer, place 70 ml. of oleum (20 per cent. SO3) and heat it in an oil bath to 70°. By means of a separatory funnel, supported so that the stem is just above the surface of the acid, introduce 41 g. (34 ml.) of nitrobenzene slowly and at such a rate that the temperature of the well-stirred mixture does not rise above 100-105°. When all the nitrobenzene has been introduced, continue the heating at 110-115° for 30 minutes. Remove a test portion and add it to the excess of water. If the odour of nitrobenzene is still apparent, add a further 10 ml. of fuming sulphuric acid, and heat at 110-115° for 15 minutes the reaction mixture should then be free from nitrobenzene. Allow the mixture to cool and pour it with good mechanical stirring on to 200 g. of finely-crushed ice contained in a beaker. AU the nitrobenzenesulphonic acid passes into solution if a little sulphone is present, remove this by filtration. Stir the solution mechanically and add 70 g. of sodium chloride in small portions the sodium salt of m-nitro-benzenesulphonic acid separates as a pasty mass. Continue the stirring for about 30 minutes, allow to stand overnight, filter and press the cake well. The latter will retain sufficient acid to render unnecessary the addition of acid in the subsequent reduction with iron. Spread upon filter paper to dry partially. 

Dissolve 46-5 g. (45-5 ml.) of aniUne in a mixture of 126 ml. of concentrated hydrochloric acid and 126 ml. of water contained in a 1-htre beaker. Cool to 0-5° in a bath of ice and salt, and add a solution of 36-5 g. of sodium nitrite in 75 ml. of water in small portions stir vigorously with a thermometer (1) and maintain the temperature below 10°, but preferably at about 5° by the addition of a httle crushed ice if necessary. The diazotisation is complete when a drop of the solution diluted with 3-4 drops of water gives an immediate blue colouration with potassium iodide - starch paper the test should be performed 3-4 minutes after the last addition of the nitrite solution. Prepare a solution of 76 g. of sodium fluoborate (2) in 150 ml. of water, cool, and add the chilled solution slowly to the diazonium salt solution the latter must be kept well stirred (1) and the temperature controlled so that it is below 10°. Allow to stand for 10 minutes with frequent stirring. Filter... 

I) An alternative procedure is to cool the solution containing the sodium sul. phanilate and sodium nitrite in a bath of crushed ice to about 5° and then add 10-5 ml. of concentrated hydrochloric acid diluted with an equal volume of water slowly and with stirring the temperature must not be allowed to rise above 10 and an excess of nitrous acid should be present (the solution is tested after standing for 5 minutes). The subsequent stages in the preparation—addition of dimethyl-aniline solution, etc.—are as above. 

Dissolve 1 g. of the secondary amine in 3-5 ml. of dilute hydrochloric acid or of alcohol (in the latter case, add 1 ml. of concentrated hydrochloric acid). Cool to about 5° and add 4-5 ml. of 10 per cent, sodium nitrite solution, and allow to stand for 5 minutes. Add 10 ml. of water, transfer to a small separatory funnel and extract the oil with about 20 ml. of ether. Wash the ethereal extract successively with water, dilute sodium hydroxide solution and water. Remove the ether on a previously warmed water bath no flames should be present in the vicinity. Apply Liebermann s nitroso reaction to the residual oil or solid thus. Place 1 drop or 0 01-0 02 g. of the nitroso compovmd in a dry test-tube, add 0 05 g. of phenol and warm together for 20 seconds cool, and add 1 ml. of concentrated sulphuric acid. An intense green (or greenish-blue) colouration will be developed, which changes to pale red upon pouring into 30-50 ml. of cold water the colour becomes deep blue or green upon adding excess of sodium hydroxide solution. 

Dissolve 1 0 g. of the compound in 5 ml. of dry chloroform in a dry test-tuhe, cool to 0°, and add dropwise 5g. (2-8 ml.) of redistilled chloro-sulphonic acid. When the evolution of hydrogen chloride subsides, allow the reaction mixture to stand at room temperature for 20 minutes. Pour the contents of the test-tube cautiously on to 25 g. of crushed ice contained in a small beaker. Separate the chloroform layer and wash it with a httle cold water. Add the chloroform layer, with stirring, to 10 ml. of concentrated ammonia solution. After 10 minutes, evaporate the chloroform on a water bath, cool the residue and treat it with 5 ml. of 10 per cent, sodium hydroxide solution the sulphonamide dissolves as the sodium derivative, RO.CgH4.SO,NHNa. Filter the solution to remove any insoluble matter (sulphone, etc.), acidify the filtrate with dilute hydrochloric acid, and cool in ice water. Collect the sulphonamide and recrystallise it from dilute alcohol. 

Place in a dry test-tube 0 -5 g. of the compound and an equal bulk of pure phthahc anhydride, mix well together, and add 1 drop of concentrated sulphuric acid. Stand the tube for 3-4 minutes in a smah beaker of concentrated sulphuric acid or oil previously heated to 160°, Remove from the bath, allow to cool, add 4 ml. of 5 per cent, sodium hydroxide solution and stir until the fused mass has dissolved. Dilute with an equal... 

Methyl p-toluenesulphonate. This, and other alkyl esters, may be prepared in a somewhat similar manner to the n-butyl ester with good results. Use 500 g. (632 ml.) of methyl alcohol contained in a 1 litre three-necked or bolt-head flask. Add 500 g. of powdered pure p-toluene-sulphonyl chloride with mechanical stirring. Add from a separatory funnel 420 g. of 25 per cent, sodium hydroxide solution drop by drop maintain the temperature of the mixture at 23-27°. When all the alkali has been introduced, test the mixture with litmus if it is not alkaline, add more alkali until the mixture is neutral. Allow to stand for several hours the lower layer is the eater and the upper one consists of alcohol. Separate the ester, wash it with water, then with 4 per cent, sodium carbonate solution and finally with water. Dry over a little anhydrous magnesium sulphate, and distil under reduced pressure. Collect the methyl p-toluenesulphonate at 161°/10 mm. this solidifies on cooling and melts at 28°. The yield is 440 g. 

Recovery of the wopropyl alcohol. It is not usually economical to recover the isopropyl alcohol because of its lo v cost. However, if the alcohol is to be recovered, great care must be exercised particularly if it has been allowed to stand for several days peroxides are readily formed in the impure acetone - isopropyl alcohol mixtures. Test first for peroxides by adding 0-6 ml. of the isopropyl alcohol to 1 ml. of 10 per cent, potassium iodide solution acidified with 0-6 ml. of dilute (1 5) hydrochloric acid and mixed with a few drops of starch solution if a blue (or blue-black) coloration appears in one minute, the test is positive. One convenient method of removing the peroxides is to reflux each one litre of recovered isopropyl alcohol with 10-15 g. of solid stannous chloride for half an hour. Test for peroxides with a portion of the cooled solution if iodine is liberated, add further 5 g. portions of stannous chloride followed by refluxing for half-hour periods until the test is negative. Then add about 200 g. of quicklime, reflux for 4 hours, and distil (Fig. II, 47, 2) discard the first portion of the distillate until the test for acetone is negative (Crotyl Alcohol, Note 1). Peroxides generally redevelop in tliis purified isopropyl alcohol in several days. 

The density determination may be carried out at the temperature of the laboratory. The liquid should stand for at least one hour and a thermometer placed either in the liquid (if practicable) or in its immediate vicinity. It is usually better to conduct the measurement at a temperature of 20° or 25° throughout this volume a standard temperature of 20° will be adopted. To determine the density of a liquid at 20°, a clean, corked test-tube containing about 5 ml. of toe liquid is immersed for about three-quarters of its length in a water thermostat at 20° for about 2 hours. An empty test-tube and a shallow beaker (e.g., a Baco beaker) are also supported in the thermostat so that only the rims protrude above the surface of the water the pycnometer is supported by its capillary arms on the rim of the test-tube, and the small crucible is placed in the beaker, which is covered with a clock glass. When the liquid has acquired the temperature of the thermostat, the small crucible is removed, charged with the liquid, the pycnometer rapidly filled and adjusted to the mark. With practice, the whole operation can be completed in about half a minute. The error introduced if the temperature of the laboratory differs by as much as 10° from that of the thermostat does not exceed 1 mg. if the temperature of the laboratory is adjusted so that it does not differ by more than 1-2° from 20°, the error is negligible. The weight of the empty pycnometer and also filled with distilled (preferably conductivity) water at 20° should also be determined. The density of the liquid can then be computed. 

It is usually preferable to oxidise the compound directly as follows. Intimately mix 0 02-0 05 g. of the eompound with 3 g. of sodium peroxide and 2 g. of anhydrous sodium carbonate in a niekel erucible. Heat the crueible and its eontents with a small flame, gently at first, afterwards more strongly until the eontents are fused, and eontinue heating for a further 10 minutes. Allow to stand, extract the contents of the crucible with water, and filter. Add exeess of eoneentrated nitrie acid to the filtrate and test with ammonium molybdate reagent as above. A yellow preeipitate indicates the presenee of phosphorus. It must be borne in mind that the above treatment 1 eonvert any arsenie present into arsenate. 

Apply the test to compounds which contain chlorine or bromine. If the compound is a solid, dissolve 0 1 g. in the minimum volume of pure, dry acetone. To 1 ml. of the sodium iodide acetone reagent add 2 drops of the compound (if a hquid) or the acetone solution (if a sohd). Shake and allow to stand at room temperature for 3 minutes. Note whether a precipitate is formed and also whether the solution acquires a reddish-brown colour (liberation of iodine). If no change takes place at rocrm temperature, place the test-tube in a beaker of water at 50°. After 5 minutes, cool to room temperature, and observe whether a reaction has occurred. 

ADF (we tested Version 1999.02) stands for Amsterdam density functional. This is a DFT program with several notable features, including the use of a STO basis set and the ability to perform relativistic DFT calculations. Both LDA and... 

YAcHMOP stands for yet another extended Hiickel molecular orbital package. The package has two main executables and a number of associated utilities. The bind program does molecular and crystal band structure extended Hiickel calculations. The viewkel program is used for displaying results. We tested Version 3.0 of bind and Version 2.0 of viewkel. 

---