Temperature polybutadiene

This lower has a number of ramifications on the properties of polybutadiene. For example, at room temperature polybutadiene compounds generally have a higher resilience than similar natural rubber compounds. In turn this means that the polybutadiene rubbers have a lower heat build-up and this is important in tyre applications. On the other hand, these rubbers have poor tear resistance, poor tack and poor tensile strength. For this reason, the polybutadiene rubbers are seldom used on their own but more commonly in conjunction with other materials. For example, they are blended with natural rubber in the manufacture of truck tyres and, widely, with SBR in the manufacture of passenger car tyres. The rubbers are also widely used in the manufacture of high-impact polystyrene. 

Polyester diols are often combined with polyether diols to provide green strength through crystallization or elevated r . Most prevalent and least expensive is hexamethylene diol adipate (HDA) with a Tm of about 60°C. A variety of polyesters are available with various levels of crystallinity — from wax-like to amorphous — and crystallization rate, and with values ranging well below 0°C to above room temperature. Polybutadiene diols are the most expensive and most hydrophobic. They provide low surface tension and thus good wet out of non-polar surfaces. 

Unlike polybutadiene, polyisoprene prepared at low temperatures shows little or no inclination to crystallize either on stretching or cooling. This may seem surprising in view of the even greater preponderance of trans-1 4 units in polyisoprene than in poly butadiene. The explanation for the contrasting behavior in this respect between low temperature synthetic polyisoprene, on the one hand, and guttapercha and low temperature polybutadiene, on the other, probably is to be found in the appreciable occurrence of head-to-head and tail-to-tail sequences of 1,4 units of the former. 

The incorporation of metals in polymers will not be covered in detail because only a limited number of reports exist on this subject. The major interactions that have been used for the incorporation of metals in polymers are those of ftmctional groups that form polymer-metal oxide-based composites. The incorporation of metals leads to dramatic changes in the properties of polymers, such as an increase of the glass-transition temperature Polybutadiene or polyisoprene incorporating palladium salts can imdergo crosslinking, mediated by palladium, between polymer... 

A diblock copolymer, 71% polyisoprene (1) by weight and 29% polybutadiene (B), was blended in different proportions into a 71%-29% mixture of the individual homopolymers. The loss tangent was measured as a function of temperature for various proportions of copolymer. Two peaks are observed ... 

Carbon Cha.in Backbone Polymers. These polymers may be represented by (4) and considered derivatives of polyethylene, where n is the degree of polymeriza tion and R is (an alkyl group or) a functional group hydrogen (polyethylene), methyl (polypropylene), carboxyl (poly(acryhc acid)), chlorine (poly(vinyl chloride)), phenyl (polystyrene) hydroxyl (poly(vinyl alcohol)), ester (poly(vinyl acetate)), nitrile (polyacrylonitrile), vinyl (polybutadiene), etc. The functional groups and the molecular weight of the polymers, control thek properties which vary in hydrophobicity, solubiUty characteristics, glass-transition temperature, and crystallinity. 

The glass-transition temperature in amorphous polymers is also sensitive to copolymerization. Generally, T of a random copolymer falls between the glass-transition temperatures of the respective homopolymers. For example, T for solution-polymerized polybutadiene is —that for solution-polymerized polystyrene is -HlOO°C. A commercial solution random copolymer of butadiene and styrene (Firestone s Stereon) shows an intermediate T of —(48). The glass-transition temperature of the random copolymer can sometimes be related simply as follows ... 

In these mbber-modified polystyrene polymers, the mbbers should have low T, large particle sizes (0.5—5 J.m), graftable and cross-linkable sites, and should be compatible with styrene monomer (93). Polybutadiene, with a T of —SS C, meets all of these requirements and is used most frequently. These mbber-modified systems exhibit excellent low temperature impact strength, a required attribute for use in refrigerators. 

Processings and Properties. Polybutadiene is compounded similarly to SBR and vulcanised with sulfur. The high cis-1,4 type crystallizes poorly on stretching so it is not suitable as a "gum" stock but requires carbon black reinforcement. It is generally used for automotive tires in mixtures with SBR and natural mbber. Its low T (—OS " C) makes it an excellent choice for low temperature tire traction, and also leads to a high resilience (better than natural mbber) which ia turn results ia a lower heat build-up. Furthermore, the high i j -polybutadiene also has a high abrasion resistance, a plus for better tire tread wear. 

Thermoplastic Elastomers. These represent a whole class of synthetic elastomers, developed siace the 1960s, that ate permanently and reversibly thermoplastic, but behave as cross-linked networks at ambient temperature. One of the first was the triblock copolymer of the polystyrene—polybutadiene—polystyrene type (SheU s Kraton) prepared by anionic polymerization with organoHthium initiator. The stmcture and morphology is shown schematically in Figure 3. The incompatibiHty of the polystyrene and polybutadiene blocks leads to a dispersion of the spherical polystyrene domains (ca 20—30 nm) in the mbbery matrix of polybutadiene. Since each polybutadiene chain is anchored at both ends to a polystyrene domain, a network results. However, at elevated temperatures where the polystyrene softens, the elastomer can be molded like any thermoplastic, yet behaves much like a vulcanized mbber on cooling (see Elastomers, synthetic-thermoplastic elastomers). 

This combination of monomers is unique in that the two are very different chemically, and in thek character in a polymer. Polybutadiene homopolymer has a low glass-transition temperature, remaining mbbery as low as —85° C, and is a very nonpolar substance with Htde resistance to hydrocarbon fluids such as oil or gasoline. Polyacrylonitrile, on the other hand, has a glass temperature of about 110°C, and is very polar and resistant to hydrocarbon fluids (see Acrylonitrile polymers). As a result, copolymerization of the two monomers at different ratios provides a wide choice of combinations of properties. In addition to providing the mbbery nature to the copolymer, butadiene also provides residual unsaturation, both in the main chain in the case of 1,4, or in a side chain in the case of 1,2 polymerization. This residual unsaturation is useful as a cure site for vulcanization by sulfur or by peroxides, but is also a weak point for chemical attack, such as oxidation, especially at elevated temperatures. As a result, all commercial NBR products contain small amounts ( 0.5-2.5%) of antioxidant to protect the polymer during its manufacture, storage, and use. 

Syndiotactic Polybutadiene. Syndiotactic polybutadiene is a unique material that combines the properties of plastic and mbber. It melts at high (150—220°C) temperatures, depending on the degree of crystallinity in the sample, and it can be molded into thin films that are flexible and have high elongation. The unique feature of this plastic-like material is that it can be blended with natural mbber. 1,4-Polybutadiene and the resulting blends exhibit a compatible formulation that combines the properties of plastic and mbber. 

Prepa.ra.tion, The preparation of amorphous high (99%) 1,2-polybutadiene was first reported iu 1981 (27). The use of a heterocycHc chelating diamine such as dipiperidine ethane iu the polymerization gave an amorphous elastomeric polymer of 99.9% 1,2 units and a glass-transition temperature of +5°C. In a previous description (53,54) of the use of a chelating diamine such as A/A/N(N -tetramethylethylene diamine, an 80% 1,2-polybutadiene with a glass-transition temperature of —30°C was produced. 

The /n j -I,4-polybutadiene made by transition-metal catalysis (112,113) is a resin-like material that has two melting temperatures, 50 and I50°C. 

A large volume usage of S—B—S-based compounds is ia footwear. Canvas footwear, such as sneakers and unit soles, can be made by injection mol ding. Frictional properties resemble those of conventionally vulcanised mbbers and are superior to those of the flexible thermoplastics, such as plasticized poly(vinyl chloride). The products remain flexible under cold conditions because of the good low temperature properties of the polybutadiene segment. 

Inclusion of double bonds will stiffen the chain at the point of inclusion but at the same time may increase the flexibility of adjacent bonds. The net effect may therefore be to reduce the glass transition temperature and this appears to occur in 1,4-polybutadiene when compared with polyethylene. 

Notable among the alternative materials are the MBS polymers, in which methyl methacrylate and styrene are grafted on to the polybutadiene backbone. This has resulted in two clear-cut advantages over ABS. The polymers could be made with high clarity and they had better resistance to discolouration in the presence of ultraviolet light. Disadvantages of MBS systems are that they have lower tensile strength and heat deflection temperature under load. 

The epoxidised polybutadiene resins available to date are more viscous than the diglycidyl ethers except where volatile diluents are employed. They are less reactive with amines but have a similar reactivity with acid anhydride hardeners. Cured resins have heat distortion temperatures substantially higher than the conventional amine-cured diglycidyl ether resins. A casting made from an epoxidised polybutadiene hardened with maleic anhydride and cured for two hours at 50°C plus three hours at 155°C plus 24 hours at 200°C gave a heat... 

The minimum service temperature is determined primarily by the Tg of the soft phase component. Thus the SBS materials ctm be used down towards the Tg of the polybutadiene phase, approaching -100°C. Where polyethers have been used as the soft phase in polyurethane, polyamide or polyester, the soft phase Tg is about -60°C, whilst the polyester polyurethanes will typically be limited to a minimum temperature of about 0°C. The thermoplastic polyolefin rubbers, using ethylene-propylene materials for the soft phase, have similar minimum temperatures to the polyether-based polymers. Such minimum temperatures can also be affected by the presence of plasticisers, including mineral oils, and by resins if these become incorporated into the soft phase. It should, perhaps, be added that if the polymer component of the soft phase was crystallisable, then the higher would also affect the minimum service temperature, this depending on the level of crystallinity. 

---