Standardized parts

ISO 9000-1 Quality management and quality assurance standards - Part 1 Guidelines for selection and use ... 

ASTM Standards, Part 12—Chemical Mnalysis of Metals and Metal Bearing Ores, Std. E40-58,1974, pp. 192—193. 

Analysis andTesting of Coal And Coke, British Standards, parts 1—16,1957—1964, p. 1016. 

Analytical Atomic Spectroscopy Surface Analysis," Mnnual Book ofMSTM Standards, part 3.06, American Society for Testing and Matedals, Philadelphia, Pa., 1992. 

Book ofMSTM Standards, Part 29, D-891, Method C, Ameiican Society foi Testing and Mateiials, Philadelphia, Pa., 1977. 

Annual Book of ASTM Standards, Part 26, Gaseous Fuels Coal and Coke Atmospheric Analysis." American Society for Testing and Materials, Philadelphia, 1981. 

ASTM Standard D 2779-69 (reapproved 1974), 1974 Annual Book of ASTM Standards, Part 24, pp. 679-682. 

Plane Strain Fracture Toughness of Metallic Materials, 1982 Annual Book of ASTM Standards, Part 10, Standard No. E399. 

The requirements within the product specification need to be expressed in terms that can be verified. Hence you should avoid subjective terms such as good quality components , high reliability , commercial standard parts , etc. as these requirements are not sufficiently definitive to be verified in a consistent manner. (See the later section on Design acceptance criteria and Part 2 Chapter 2 on Clarifying standards of acceptabili-fy-)... 

For most process applications, the materia s of construction can be accommodated to fit both the corrosive-erosive and mechanical strength requirements. Manufacturers have established standard materials which will fit a large percentage of the applications, and often only a few parts need to be changed to adapt the valve to a corrosive service. Typical standard parts are (See Figures 7-3, 7-3A, and 7-4)... 

ASTM C 150 Standard Specifications for Porland Cement, Book of ASTM Standards, Part 13, ASTM Publication, 1987. 

Accurate radial Axial load capacity Low starting Silent Standard parts Simple ... 

Unquestionably the best way to achieve that end would have been to rewrite the book, to expand its size and its scope, along some lines which are still unconventional but hold out promise for future interest. The prospect of undertaking this frightened us. Also, we acknowledge that there already exists a monumental treatise of this elaborate sort, dedicated to the standard parts of the newer mathematics, in the work of Morse and Feshbach, whose excellence would be hard to approach. We, therefore, decided upon the less ambitious course of editing a work which offers what we regard as the most important components of today s useful mathematics in separate chapters written chiefly by experts. 

Guin e, J.B. (ed.), Gorree, M., Heijimgs, R. et al. (2001) Life Cycle Assessment - An Operational Guideline to the ISO Standards - Part 2a. Ministry of Housing, Spatial Planning and the Environment and Centre of Environmental Science - Leiden University, The Netherlands. 

Anerican Society for Testing Materials, "Standard Practice for Testing Fixed-Wavelength Photonetric Detectors used in Liquid Chronatography", Annual Book of ASTM Standards Part 12, E685, Philadelphia, Pennsylvania, 1990. 

Bogusz, M., Franke, J. P., de Zeeuw, R. A., and Erkens, M., An overview of the standardization of chromatographic methods for screening analysis in toxicology by means of retention indices and secondary standards. Part II. High performance liquid chromatography, Fresenius ]. Anal. Chem., 347, 73, 1993. 

CFR, Metal Molding and Casting Industry Point Source Category Effluent Limitations Guidelines, Pretreatment Standards and New Source Performance Standards, Part 464, Code of Federal Register,... 

The application of theoretical tools for predicting molecular structure, such as ab initio calculations and density functional methods, are discussed in Chapter 6. These tools provide only a first approximation to the molecular structure. There is much room for further development of theoretical molecular structure calculations, but even so such methods have already become a standard part of molecular structure determinations. 

Chemistry-Layouts for Standards - Part 2 Methods of Chemical Analysis , ISO 78-2 1999, International Organization for Standardization (ISO), Geneva, Switzerland, 1999. 

Pressure Relief Device Standards—Part 2—Cargo and Portable Tanks for Compressed Gases... 

The Object Constraint Language (OCL), a standard part of UML 1.1, is a specification language used in conjunction with UML models. It is an expression-based, side-effect-free language that eschews mathematical symbols (V, 3, and so on) for textual equivalents (forAII, exists). It uses a syntax more usual in object-oriented languages V x T, p(x) becomes T->forAII (x x.p). 

ASTM. 1978. Annual book of astm standards part 31, water. Method No. D1783, ASTM, Philadelphia, PA. p. 650-655. 

Relative to the processing cost of a standard part injected at 1 million units... 

For surgical parts, the replacement of stainless steel by liquid crystal polymer (TCP) leads to a material cost of the same order, but the ease of TCP processing compared to metal results in a lower final cost. The cost savings are about 50% for some standard parts and up to 90% for high-tech parts. 

Standard method of test for continuous analysis and automatic recording of the oxidant content of the atmosphere. Designation D 2011-65 (Reapproved 1972), pp. 924-928. In 1973 Annual Book of ASTM Standards. Part 23. Water Atmospheric Analysis. Philadelphia American Society for Testing and Materials, 1973. 

Annual Book of ASTM Standards", Part 27, "Paint - Tests for Formulated Products and Applied Coatings", American Society for Testing and Materials Philadelphia, issued annually. 

ISO 78-3 1983 Chemistry - Layouts for standards - Part 3 Standard for molecular absorption spectrometry... 

A medium-pressure apparatus is assembled from a stainless steel bomb, standard parts, valves, unions and copper or stainless steel tubing according to Fig. 4. 

Fireworks, British Standard Parts 1, 2 and 3, BS 7114, British Standards Institution, Milton Keynes, 1988. 

---