Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Spectroscopic analytical method

It was mentioned earlier that empirical multivariate modeling often reqnires a very large amount of data. These data can contain a very large number of samples (IN), a very large number of variables (M) per sample, or both. In the case of PAT, where spectroscopic analytical methods are often used, the number of variables collected per process sample can range from the hundreds to the thonsands ... [Pg.362]

Highly specific information concerning the chemical nature and concentration of each moiety in coal and coal conversion products is desirable if extensive coal utilization is to be achieved.(1 ) Considering the high complexity and heterogeneous nature of each sample, multiple, information-specific, chromatographic-spectroscopic analytical methods are required. In solution, where the maximum information is achieveable the analysis problem is further complicated by the fact that most conventional spectroscopic and chromatographic solvents have little affinity for coal and coal liquids. [Pg.163]

The fate of organic contaminants in soils and sediments is of primary concern in environmental science. The capacity to which soil constituents can potentially react with organic contaminants may profoundly impact assessments of risks associated with specific contaminants and their degradation products. In particular, clay mineral surfaces are known to facilitate oxidation/reduction, acid/base, polymerization, and hydrolysis reactions at the mineral-aqueous interface (1, 2). Since these reactions are occurring on or at a hydrated mineral surface, non-invasive spectroscopic analytical methods are the preferred choice to accurately ascertain the reactant products and to monitor reactions in real time, in order to determine the role of the mineral surface in the reaction. Additionally, the in situ methods employed allow us to monitor the ultimate changes in the physico-chemical properties of the minerals. [Pg.282]

F. Maya, J.M. Estela, V. Cerda, Multisyringe flow injection analysis hyphenated with Uquid core waveguides for the development of cleaner spectroscopic analytical methods improved determination of chloride in waters. Anal. Bioanal. Chem. 394 (2009) 1577—1583. [Pg.159]

An overview of fast identification of plastics in recycling processes by means of spectroscopic analytical methods has recently appeared [150]. While there have been some promising results in identification and separation of mixed plastics packaging waste, there is still much work to be done in the more complex technical and engineering compounds [158],... [Pg.353]

Finally, analytical methods can be compared in terms of their need for equipment, the time required to complete an analysis, and the cost per sample. Methods relying on instrumentation are equipment-intensive and may require significant operator training. For example, the graphite furnace atomic absorption spectroscopic method for determining lead levels in water requires a significant capital investment in the instrument and an experienced operator to obtain reliable results. Other methods, such as titrimetry, require only simple equipment and reagents and can be learned quickly. [Pg.44]

The focus of this chapter is photon spectroscopy, using ultraviolet, visible, and infrared radiation. Because these techniques use a common set of optical devices for dispersing and focusing the radiation, they often are identified as optical spectroscopies. For convenience we will usually use the simpler term spectroscopy in place of photon spectroscopy or optical spectroscopy however, it should be understood that we are considering only a limited part of a much broader area of analytical methods. Before we examine specific spectroscopic methods, however, we first review the properties of electromagnetic radiation. [Pg.369]

Air Monitoring. The atmosphere in work areas is monitored for worker safety. Volatile amines and related compounds can be detected at low concentrations in the air by a number of methods. Suitable methods include chemical, chromatographic, and spectroscopic techniques. For example, the NIOSH Manual of Analytical Methods has methods based on gas chromatography which are suitable for common aromatic and aHphatic amines as well as ethanolamines (67). Aromatic amines which diazotize readily can also be detected photometrically using a treated paper which changes color (68). Other methods based on infrared spectroscopy (69) and mass spectroscopy (70) have also been reported. [Pg.264]

The unique chemical, physical, and spectroscopic properties of organosiUcon compounds are reflected in the analytical methodology used for the detection, quantification, and characterization of these compounds. Several thorough, up-to-date reviews dealing with analytical methods appHed to siUcones have beenpubhshed (434—436). [Pg.59]

The objective ia any analytical procedure is to determine the composition of the sample (speciation) and the amounts of different species present (quantification). Spectroscopic techniques can both identify and quantify ia a single measurement. A wide range of compounds can be detected with high specificity, even ia multicomponent mixtures. Many spectroscopic methods are noninvasive, involving no sample collection, pretreatment, or contamination (see Nondestructive evaluation). Because only optical access to the sample is needed, instmments can be remotely situated for environmental and process monitoring (see Analytical METHODS Process control). Spectroscopy provides rapid real-time results, and is easily adaptable to continuous long-term monitoring. Spectra also carry information on sample conditions such as temperature and pressure. [Pg.310]

Modem analytical techniques have been developed for complete characteri2ation and evaluation of a wide variety of sulfonic acids and sulfonates. The analytical methods for free sulfonic acids and sulfonate salts have been compiled (28). Titration is the most straightforward method of evaluating sulfonic acids produced on either a laboratory or an iadustrial scale (29,30). Spectroscopic methods for sulfonic acid analysis iaclude ultraviolet spectroscopy, iafrared spectroscopy, and and nmr spectroscopy (31). Chromatographic separation techniques, such as gc and gc/ms, are not used for free... [Pg.98]

One of the attractive features of SFE with CO2 as the extracting fluid is the ability to directly couple the extraction method with subsequent analytical methods (both chromatographic and spectroscopic). Various modes of on-line analyses have been reported, and include continuous monitoring of the total SFE effluent by MS [6,7], SFE-GC [8-11], SFE-HPLC [12,13], SFE-SFC [14,15] and SFE-TLC [16]. However, interfacing of SFE with other techniques is not without problems. The required purity of the CO2 for extraction depends entirely on the analytical technique used. In the off-line mode SFE takes place as a separate and isolated process to chromatography extracted solutes are trapped or collected, often in a suitable solvent for later injection on to chromatographic instrumentation. Off-line SFE is inherently simpler to perform, since only the extraction parameters need to be understood, and several analyses can be performed on a single extract. Off-line SFE still dominates over on-line determinations of additives-an... [Pg.429]

Highly sensitive determination of "Tc is possible using today s advanced mass spectroscopic methods. However, orthodox determination methods of "Tc involving radiometric techniques or even activation analysis are still used because they are simple and can be done without expensive machines. The detection limits of typical analytical methods are listed in Table 1. [Pg.24]

We will begin by taking a look at the detailed aspects of a basic problem that confronts most analytical laboratories. This is the problem of comparing two quantitative methods performed by different operators or at different locations. This is an area that is not restricted to spectroscopic analysis many of the concepts we describe here can be applied to evaluating the results from any form of chemical analysis. In our case we will examine a comparison of two standard methods to determine precision, accuracy, and systematic errors (bias) for each of the methods and laboratories involved in an analytical test. As it happens, in the case we use for our example, one of the analytical methods is spectroscopic and the other is an HPLC method. [Pg.167]

But in order to understand what needs to be changed, we first need to understand the current situation. In order for a pharmaceutical company to use any analytical method for certifying the properties (efficacy, potency, etc.) of their products, the analytical method has to be validated. Validation , in the parlance of the FDA, is a far cry from what we usually call validation when developing a multivariate spectroscopic method. In fact, what we call validation in spectroscopic calibration (which usually means calculating an SEP, or an SECV) is a far cry from the dictionary definition of validate , which is to make legally valid , where valid is defined as having legal efficacy or force [11],... [Pg.423]

We will discuss in some detail examples where various methods of separation, including chemical derivatization, were complemented by spectroscopic identification. However, even the use of the most advanced analytical methods frequently yields only partial... [Pg.485]

When the co-crystallised samples were irradiated with UV light for several hours, the stereospecific (100%) formation of rcff-tetrakis(4-pyridyl)cyclobutane (99) was observed. This was confirmed by spectroscopic, analytical and structural methods. The latter showed that, once irradiated, the new co-crystallized materials (99) 2(97) and (99)-2(98) are formed respectively. In both these structures the molecular components are held together by hydrogen bonding interactions. [Pg.136]

To put things into perspective, we. can broadly classify these analytical methods into bulk, dry surface, and in situ interfacial techniques. This chapter focuses on the last category, illustrating two in situ techniques used to study anion binding at the goethite (a-FeOOH)-water interface titration calorimetry and cylindrical internal reflection-Fourier transform infrared (CIR-FTIR) spectroscopy. In fact, CIR-FTIR could prove to be extremely powerful, since it allows direct spectroscopic observation of ions adsorbed at the mineral-water interface. [Pg.143]


See other pages where Spectroscopic analytical method is mentioned: [Pg.59]    [Pg.34]    [Pg.96]    [Pg.373]    [Pg.710]    [Pg.251]    [Pg.59]    [Pg.34]    [Pg.96]    [Pg.373]    [Pg.710]    [Pg.251]    [Pg.80]    [Pg.302]    [Pg.340]    [Pg.419]    [Pg.418]    [Pg.52]    [Pg.122]    [Pg.19]    [Pg.20]    [Pg.197]    [Pg.671]    [Pg.332]    [Pg.39]    [Pg.3]    [Pg.59]    [Pg.116]    [Pg.203]    [Pg.423]    [Pg.556]    [Pg.443]    [Pg.270]    [Pg.257]    [Pg.234]    [Pg.691]    [Pg.86]    [Pg.353]    [Pg.288]   
See also in sourсe #XX -- [ Pg.265 , Pg.274 ]




SEARCH



Spectroscopic methods

© 2024 chempedia.info