Sodium calcium chloride

Tests were also run with simulated brackish agricultural drainage water, as illustrated in Table 4. A feedwater composition containing sodium, calcium, chloride, sulfate, and bicarbonate ions was prepared in such a way as to duplicate the water in the Mohawk-Wellton drainage canal at Yuma, Arizona. Salt rejections were relatively poor toward this synthetic feedwater, but when this water was line-softened and acidified to pH 5.5 with sulfuric acid, salt rejection of the 90 10 copolyamide improved markedly. However, the membrane s water flux declined by nearly 50 percent. Salt rejection and flux were found in this and other examples to be markedly dependent on pH. As the pH approached the pKa of... 

Special attention is being given to mineral extraction from bitterns formed by solar evaporation of seawater in arid waters or by seawater freezing in the Arctic areas. Such bitterns represent approximately 30-fold concentrated seawater with depleted concentrations of sodium, calcium, chloride and sulfate ions. 

Intracellular fluids (also called the cytosol) are quite different compositionally from plasma and interstitial fluids (Table 4, Figures 4 and 5). The internal pH of many cells is maintained near 6.9-7.0. via various membrane transport mechanisms such as Na" /H and CP/HCO exchangers, and various phosphate and protein buffers. In contrast to the plasma, the intracellular fluids have substantially lower concentrations of sodium, calcium, chloride, and bicarbonate and higher to substantially higher concentrations of potassium, magnesium,... 

Figure 5 compares the ions that might be attributed to road salt use and acidic deposition in the northern cities. These include sodium, calcium, chloride, and sulfate they were major constituents. While the northern cities have expectedly high levels of these ionic species, the levels in Dallas were unexpected. Further observation pointed out important differences in the chemistry of the environments as described below. 

The experimental data showed that at 25 °C, the residual strontium concentration is apix-oximately the same in the 2.5 M sodium chloride solutions in the system NaCl-SrCV NaOH-H20, and NaCl-SrCl2-CaCl2-Na0H-H20. At 75 °C the degree of strontium extraction is twice that of the sodium calcium chloride solutions. 

The description of the test apparatus is described elsewher (Thomas et al 1998), and is shown in Fig 1. The apparatus comprises of a horizontal stainless steel plate rig, with a central circular recess of SOmm diameter and 2mm deep. There is a small hole in which the volatile/malodorous test solution is fed via a mechaiucal syriige pump. This is to simulate an exudating wound. The test solution consisting of sodium/calcium chloride solution containing 142 mmol of sodium ions and 2,5mmol of calcium ions as the chloride salts ffhe concentration of which is quoted to be comparable to human serum or wound exudate), 2% diethylamine (odorous volatile) and 10% newborn bovine serum (fatty acids), simulating wound exudate. 

In general, if the flow rate is increased above the unstimulated rate the sodium, calcium, chloride, bicarbonate and protein concentrations and pH increase, whereas the phosphate, magnesium and urea concentrations decrease while potassium shows little change. At very high rates of flow the composition of saliva, which is normally hypotonic, tends to approach that of plasma. 

If a compound has been recrystallised from petrol, benzene, etc.y some freshly cut shavings of clean paraffin wax should be added to the calcium chloride in (A) or to the sodium hydroxide in D, The surface of the wax absorbs organic solvent vapours (particularly the hydrocarbons) and the last trace of such solvents is thus readily removed from the recrystallised material. 

Both forms sublime very readily, even at room temperature a small sample on exposure to the air will completely volatilise in a short time, particularly on a warm day or if the sample is exposed to a gentle current of air. Hence the above method for rapid drying. A sample confined in an atmospheric desiccator over calcium chloride rapidly disappears as the vapour is adsorbed by the calcium chloride. A sample of the hexahydrate similarly confined over sodium hydroxide undergoes steady dehydration with initial liquefaction, for the m.p. of the hydrated-anhydrous mixture is below room temperature as the dehydration proceeds to completion, complete resolidification occurs. 

Aluminium isopropoxide can be obtained as a fine powder from technical sources. When the bottle has once been opened however, the stopper should be firmly replaced and covered with wax more conveniently, the stoppered bottle can be kept in an atmospheric desiccator over calcium chloride or sodium hydroxide, preferably in the dark. 

Place the distillate in a separating-funnel and extract the benzonitrile twice, using about 30 ml. of ether for each extraction. Return the united ethereal extracts to the funnel and shake with 10% sodium hydroxide solution to eliminate traces of phenol formed by decomposition of the benzenediazonium chloride. Then run off the lower aqueous layer, and shake the ethereal solution with about an equal volume of dilute sulphuric acid to remove traces of foul-smelling phenyl isocyanide (CaHjNC) which are always present. Finally separate the sulphuric acid as completely as possible, and shake the ether with water to ensure absence of acid. Run off the water and dry the benzonitrile solution over granular calcium chloride for about 20 minutes. 

Fit a 750 ml, bolt-head flask (also by a rubber stopper) to a reflux water-condenser closed at the top by a calcium chloride tube ensure that flask and condenser are quite dr). Place 150 ml. of the dried ethyl acetate in the flask and add 15 g. of sodium. The sodium for this purpose should preferably be added in the form of wire directly from a sodium press (Fig. 55, p. 82) alternatively the sodium may be added as thin slices, but in this case each slice should be quickly pressed between drying-paper before being added to the acetate to remove the wet film which may have formed during the weighing and cutting of the metal. 

Refractionation of the low-boiling impurities gives a further quantity of the acetoacetate, but if the initial distillation has been carefully conducted, the amount recovered is less than i g., and the refractionation is not worth while. If possible, complete the preparation in one day. If this is not possible, it is best to allow the cold crude sodium derivative (before acidification) to stand overnight, the flask being closed by a cork carrying a calcium chloride tube the yield will now fall to about 38 g. Alternatively, the crude ester may be allowed to remain overnight in contact with the sodium sulphate, but in this case the yield will fall to about 30 g. 

Dissolve 13 g. of sodium in 30 ml. of absolute ethanol in a 250 ml. flask carrying a reflux condenser, then add 10 g. (9 5 ml.) of redistilled ethyl malonate, and place the flask on a boiling water-bath. Without delay, add a solution of 5 3 g. of thiourea in a minimum of boiling absolute ethanol (about 100 ml.). The sodium salt of thiobarbituric acid rapidly begins to separate. Fit the water-condenser with a calcium chloride guard-tube (Fig. 61, p. 105), and boil the mixture on the water-bath for 1 hour. Cool the mixture, filter off the sodium salt at the pump and wash it with a small quantity of cold acetone. Dissolve the salt in warm water and liberate the acid by the addition of 30 ml. of concentrated hydrochloric acid diluted with 30 ml. of water. Cool the mixture, filter off the thiobarbituric acid, and recrystallise it from hot water. Colourless crystals, m.p. 245 with decomposition (immersed at 230°). Yield, 3 5 -4 0 g. 

Metallic sodium. This metal is employed for the drying of ethers and of saturated and aromatic hydrocarbons. The bulk of the water should first be removed from the liquid or solution by a preliminary drying with anhydrous calcium chloride or magnesium sulphate. Sodium is most effective in the form of fine wire, which is forced directly into the liquid by means of a sodium press (see under Ether, Section II,47,i) a large surface is thus presented to the liquid. It cannot be used for any compound with which it reacts or which is affected by alkalis or is easily subject to reduction (due to the hydrogen evolved during the dehydration), viz., alcohols, acids, esters, organic halides, ketones, aldehydes, and some amines. 

Alkyl halides Aryl halides Anhydrous calcium chloride anhydrous sodium, magnesium or calcium sulphate phosphorus pentoxide. 

Saturated and aromatic hydrocarbons Ethers Anhydrous calcium chloride anhydrous calcium sulphate metallic sodium phosphorus pentoxide. 

In the isolation of organic compounds from aqueous solutions, use is frequently made of the fact that the solubility of many organic substances in water is considerably decreased by the presence of dissolved inorganic salts (sodium chloride, calcium chloride, ammonium sulphate, etc.). This is the so-called salting-out effect. A further advantage is that the solubility of partially miscible organic solvents, such as ether, is considerably less in the salt solution, thus reducing the loss of solvent in extractions. 

Di-teo-propyl ether. The commercial product usually contains appreciable quantities of peroxides these should be removed by treatment with an acidified solution of a ferrous salt or with a solution of sodium sulphite (see under Diethyl ether). The ether is then dried with anhydrous calcium chloride and distilled. Pure di-iao-propyl ether has b.p. 68-5°/760 mm. 

---