Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Removing traces

This reaction is an undesirable side reaction in the manufacture of hydrogen but utilised as a means of removing traces of carbon monoxide left at the end of the second stage reaction. The gases are passed over a nickel catalyst at 450 K when traces of carbon monoxide form methane. (Methane does not poison the catalyst in the Haber process -carbon monoxide Joes.)... [Pg.181]

B) A hot solution has to be filtered to remove traces of insoluble impurities, and kept hot meanwhile to prevent crystallisation of the main solute, which would otherwise choke up the filter. [Pg.10]

B) Filtration of hot solutions. The quickest method of removing traces of insoluble impurities from a hot solution is to... [Pg.11]

The glycine so obtained is almost pure. To remove traces of ammonium chloride, however, dissolve the glycine in 30 ml. of water, and then reprecipitate by the addition of 200 ml. of methanol. Cool the product in ice-water with stirring, and then... [Pg.130]

Place the distillate in a separating-funnel and extract the benzonitrile twice, using about 30 ml. of ether for each extraction. Return the united ethereal extracts to the funnel and shake with 10% sodium hydroxide solution to eliminate traces of phenol formed by decomposition of the benzenediazonium chloride. Then run off the lower aqueous layer, and shake the ethereal solution with about an equal volume of dilute sulphuric acid to remove traces of foul-smelling phenyl isocyanide (CaHjNC) which are always present. Finally separate the sulphuric acid as completely as possible, and shake the ether with water to ensure absence of acid. Run off the water and dry the benzonitrile solution over granular calcium chloride for about 20 minutes. [Pg.192]

RCH=N—ONa and R R C=N—ONa) which may be filtered off and washed with methanol to remove traces of sodium methoxide. It should be kept moist with methanol the sodium derivative, if allowed to dry, may become very explosive. Also, upon contact with a trace of water, it is liable to decompose with explosive violence. The sodium derivative may be dissolved by successively adding small quantities to cold water with continual stirring. [Pg.531]

Hydrolysis of benzyl cyanide to phenylacetamide. In a 1500 ml. three-necked flask, provided with a thermometer, reflux condenser and efficient mechanical stirrer, place 100 g. (98 ml.) of benzyl]cyanide and 400 ml. of concentrated hydrochloric acid. Immerse the flask in a water bath at 40°. and stir the mixture vigorously the benzyl cyanide passes into solution within 20-40 minutes and the temperature of the reaction mixture rises to about 50°, Continue the stirring for an additional 20-30 minutes after the mixture is homogeneous. Replace the warm water in the bath by tap water at 15°, replace the thermometer by a dropping funnel charged with 400 ml. of cold distilled water, and add the latter with stirring crystals commence to separate after about 50-75 ml. have been introduced. When all the water has been run in, cool the mixture externally with ice water for 30 minutes (1), and collect the crude phenylacetamide by filtration at the pump. Remove traces of phenylacetic acid by stirring the wet sohd for about 30 minutes with two 50 ml. portions of cold water dry the crystals at 50-80°. The yield of phenylacetamide, m.p. 154-155°, is 95 g. RecrystaUisation from benzene or rectified spirit raises the m.p. to 156°. [Pg.762]

Acryflc acid, alcohol, and the catalyst, eg, sulfuric acid, together with the recycle streams are fed to the glass-lined ester reactor fitted with an external reboiler and a distillation column. Acrylate ester, excess alcohol, and water of esterification are taken overhead from the distillation column. The process is operated to give only traces of acryflc acid in the distillate. The bulk of the organic distillate is sent to the wash column for removal of alcohol and acryflc acid a portion is returned to the top of the distillation column. If required, some base may be added during the washing operation to remove traces of acryflc acid. [Pg.154]

The by-product ammonia is vented from the reactor during the course of the reaction. Unconverted aniline is distilled off at the end of the reaction and the diphenylamine is washed with aqueous hydrochloric acid to remove trace amounts of aniline. The product is then washed with water and purified in a refining stiU. [Pg.229]


See other pages where Removing traces is mentioned: [Pg.102]    [Pg.106]    [Pg.110]    [Pg.133]    [Pg.158]    [Pg.224]    [Pg.232]    [Pg.476]    [Pg.172]    [Pg.187]    [Pg.193]    [Pg.194]    [Pg.195]    [Pg.488]    [Pg.609]    [Pg.826]    [Pg.845]    [Pg.846]    [Pg.887]    [Pg.930]    [Pg.255]    [Pg.171]    [Pg.174]    [Pg.505]    [Pg.284]    [Pg.301]    [Pg.525]    [Pg.127]    [Pg.130]    [Pg.421]    [Pg.307]    [Pg.394]    [Pg.150]    [Pg.544]    [Pg.456]    [Pg.208]    [Pg.373]    [Pg.488]    [Pg.157]    [Pg.118]    [Pg.52]    [Pg.229]   


SEARCH



© 2024 chempedia.info