Separation, automatic

Calculate mean grey values for one or more predefined regions of the picture. These regions have to be determined by hand In a newer version of the program one or more persons can separated automatically from the background. 

Gathering emission data and putting them in condition for use in air quality models are often among the most tedious and time-consuming parts of their handling. For this reason, the preprocessing module is identified as a separate automatic operation in procedures outlined in Figure 5-1. 

Equipment used in pressing has shown considerable change in the last twenty years. Until 1960, most red pomace was pressed in vertical hydraulic basket presses. In the 1960s and 1970s, the Willmes-type pneumatic horizontal bag press as well as horizontal screw presses became popular. These were batch process operations. More recently, horizontal continuous screw presses preceded by an inclined dejuicer have appeared in the North Coast and will probably increase in popularity. They are designed to separate automatically different grades of press juice (Figure 5). 

Large columns of the N-(3,5-dinitnobenzoyl) amino acid CSPs have been prepared and multigram quantities of racemates have been separated automatically (l 9). Fifty grams of racemic methyl N-(2-naphthyl) alaninate have been resolved per pass on a 6" X 4 column containing 13 kg of chiral packing. 

According to [2] fee pipe type liquid phase distributors intended fin-pure liquids can be transformed to distributors for strongly contaminated wife solid p e ones by connection of fee single distributitm pipes wife separate automatic valves for instant feeding of high pressure lire pressure impulse... 

Logic tested separately Automatic testing Manual testing... 

The Supplement B (reference) contains a description of the process to render an automatic construction of mathematical models with the application of electronic computer. The research work of the Institute of the applied mathematics of The Academy of Sciences ( Ukraine) was assumed as a basis for the Supplement. The prepared mathematical model provides the possibility to spare strength and to save money, usually spent for the development of the mathematical models of each separate enterprise. The model provides the possibility to execute the works standard forms and records for the non-destructive inspection in complete correspondence with the requirements of the Standard. 

The fish blocks are positioned in front of the cabinet on a loading conveyor that will separate and load the first block into the cabinet and move the next block(s) one step forwards. The entrance panel will automatically open and close to admit the blocks in sequence (figure 3, overleaf). 

The success of this preparation depends upon the use of the apparatus (1) depicted in Fig.///, 57, 1, which permits of the automatic separation of the water produced in the reaction this will be termed a water-separator tube. Convenient dimensions for students preparations are indicated in the diagram. Determine the volume v of the tube up to the neck, i.e., between A and B, by adding water from a burette. The quantity of water which should be eliminated, assuming a quantitative conversion of the alcohol into the ether, may be computed from the equation ... 

Place a mixture of 53 g. of A.R. lactic acid (85-88 per cent, acid), 75 g. (85-5 ml.) of commercial anhydrous isopropyl alcohol, 300 ml. of benzene and 20 g. of Zeo-Karb 225/H (1) in a 700 ml. bolt-head flask, equipped with an automatic water separator (e.g., a large modified Dean and Stark apparatus with a stopcock at the lower end, see Fig. Ill, 126, 1) carrying an efficient reflux condenser at its upper end, and a mercury-sealed stirrer (alternatively, the hquid-sealed stirrer shown in Fig. 11,7,11, c. may be used). Reflux the mixture, with stirring, on a steam bath for 5 hours or until water no longer collects in appreciable amount in the water separator run off the water from time to time. Filter off the resin at the pump and wash it with two 25 ml. portions of benzene. Shake the combined filtrate and washings with about 5 g. of precipit-ated calcium... 

The purified commercial di-n-butyl d-tartrate, m.p. 22°, may be used. It may be prepared by using the procedure described under i o-propyl lactate (Section 111,102). Place a mixture of 75 g. of d-tartaric acid, 10 g. of Zeo-Karb 225/H, 110 g. (136 ml.) of redistilled n-butyl alcohol and 150 ml. of sodium-dried benzene in a 1-litre three-necked flask equipped with a mercury-sealed stirrer, a double surface condenser and an automatic water separator (see Fig. Ill, 126,1). Reflux the mixture with stirring for 10 hours about 21 ml. of water collect in the water separator. FUter off the ion-exchange resin at the pump and wash it with two 30-40 ml. portions of hot benzene. Wash the combined filtrate and washings with two 75 ml. portions of saturated sodium bicarbonate solution, followed by lOu ml. of water, and dry over anhydrous magnesium sulphate. Remove the benzene by distillation under reduced pressure (water pump) and finally distil the residue. Collect the di-n-butyl d-tartrate at 150°/1 5 mm. The yield is 90 g. 

Just to show you that you can t automatically separate two rings to get the right disconnection (hint ). How could you make TM 293 ... 

A small (25-kg), portable apheresis system, available in 1993, is designed to meet a wide variety of blood cell separation needs. The role of the apheresis system is to control the behavior, separation, and collection of blood components from the bowl while maintaining maximum donor safety. The system controls the flow rates of blood and components through variable pump speeds. It directs the flow of components out of the bowl, by fully automatic opening and closing of valves based on the output of the system sensors. The system monitors the separation of blood components in the bowl by an optics system that aims at the shoulder of the bowl. A sensor on the effluent line monitors the flow of components out of the bowl. 

In another extractor (Automatic Machinery and Electronics Inc. (AMC)) the individual fmits are cut in half as they pass a stationary knife. The halves are oriented in a vertical plane, picked up by synthetic mbber cups, and positioned across plastic serrated reamers revolving in a synchronized carrier in a vertical plane. As the fmit halves progress around the extractor turntable, the rotating reamers exert increasing pressure and express the juice. The oil and pulp contents in the juice increase with greater reaming pressure. The recoverable oil is removed in a separate step prior to juice extraction. Needle-sharp spikes prick the peel of the whole fmit, releasing oil that is washed away with water and recovered from the oil—water emulsion. 

PGR amplification of a DNA sequence is faciHtated by the use of a heat-stable DNA polymerase, Taq polymerase (TM), derived from the thermostable bacterium Thermus aquaticus. The thermostable polymerase allows the repeated steps of strand separation, primer annealing, and DNA synthesis to be carried out ia a single reactioa mixture where the temperature is cycled automatically. Each cycle coasists of a high temperature step to deaature the template strands, a lower temperature annealing of the primer and template, and a higher temperature synthesis step. AH components of the reaction are present ia the same tube. 

---