Saponification effects

It is frequently advisable in the routine examination of an ester, and before any derivatives are considered, to determine the saponification equivalent of the ester. In order to ensure that complete hydrolysis takes place in a comparatively short time, the quantitative saponi fication is conducted with a standardised alcoholic solution of caustic alkali—preferably potassium hydroxide since the potassium salts of organic acids are usuaUy more soluble than the sodium salts. A knowledge of the b.p. and the saponification equivalent of the unknown ester would provide the basis for a fairly accurate approximation of the size of the ester molecule. It must, however, be borne in mind that certain structures may effect the values of the equivalent thus aliphatic halo genated esters may consume alkali because of hydrolysis of part of the halogen during the determination, nitro esters may be reduced by the alkaline hydrolysis medium, etc. 

One of the most sensitive tests of the dependence of chemical reactivity on the size of the reacting molecules is the comparison of the rates of reaction for compounds which are members of a homologous series with different chain lengths. Studies by Flory and others on the rates of esterification and saponification of esters were the first investigations conducted to clarify the dependence of reactivity on molecular size. The rate constants for these reactions are observed to converge quite rapidly to a constant value which is independent of molecular size, after an initial dependence on molecular size for small molecules. The effect is reminiscent of the discussion on the uniqueness of end groups in connection with Example 1.1. In the esterification of carboxylic acids, for example, the rate constants are different for acetic, propionic, and butyric acids, but constant for carboxyUc acids with 4-18 carbon atoms. This observation on nonpolymeric compounds has been generalized to apply to polymerization reactions as well. The latter are subject to several complications which are not involved in the study of simple model compounds, but when these complications are properly considered, the independence of reactivity on molecular size has been repeatedly verified. 

The enhanced rate expressions for regimes 3 and 4 have been presented (48) and can be appHed (49,50) when one phase consists of a pure reactant, for example in the saponification of an ester. However, it should be noted that in the more general case where component C in equation 19 is transferred from one inert solvent (A) to another (B), an enhancement of the mass-transfer coefficient in the B-rich phase has the effect of moving the controlling mass-transfer resistance to the A-rich phase, in accordance with equation 17. Resistance in both Hquid phases is taken into account in a detailed model (51) which is apphcable to the reversible reactions involved in metal extraction. This model, which can accommodate the case of interfacial reaction, has been successfully compared with rate data from the Hterature (51). 

Hydrolysis. The first effect of either acid hydrolysis or alkaline hydrolysis (saponification) is the removal of the fatty acids. The saponification value of commercial lecithin is 196. Further decomposition into glycerol, phosphoric acid, and head groups (ie, choline, ethanolamine, etc) may foUow prolonged heating. Lecithin may also be hydrolyzed by enzymes. 

Comparison of Base Soap Manufacturing Routes. Direct saponification of fats and oils is well known, characteri2ed, and straightforward requires Httle equipment and is relatively energy-efficient. However, it is not very effective with regard to changes in the fats and oils ratio desired for finished soap bar formulations. Furthermore, direct saponification has the drawbacks of lower glycerol yields, limited flexibiUty toward... 

As with poly(vinyl alcohol), poly(vinyl cinnamate) is prepared by chemical modification of another polymer rather than from monomer . One process is to treat poly(vinyl alcohol) with cinnamoyl chloride and pyridine but this is rather slow. Use of the Schotten Baumann reaction will, however, allow esterification to proceed at a reasonable rate. In one example poly(vinyl alcohol) of degree of polymerisation 1400 and degree of saponification of 95% was dissolved in water. To this was added a concentrated potassium hydroxide solution and then cinnamoyl chloride in methyl ethyl ketone. The product was, in effect a vinyl alcohol-vinyl cinnamate copolymer Figure 14.8)... 

The rate of saponification of ethyl 2-thenoate, in contrast to ethyl 3-thenoate, was found to be considerably slower than predicted from the pKa of the acid, showing that the reactivities of thiophenes do not parallel those of benzene. The first explanation, that this was produced by a steric effect of the ring sulfur similar to the case in or /lo-substituted benzenes and in ethyl 1-naphthoate, could not be upheld when the same effect was found in ethyl 2-furoate. It was later ascribed to a stereospecific acid strengthening factor, involving the proper relation of the carboxylic hydrogen and the heteroatom, as the rate of saponification of 2-thienylacrylic acid was in agreement with that predicted from the acid constants. ... 

Terpinyl acetate in the absence of esters of high molecular weight, or ethyl esters of the fatty acids of coconut oil, is indicated by a difference to be observed in the apparent ester value by different times of saponification. This ester is far more resistant to the action of caustic alkali than is linalyl acetate, and requires two hours at least for complete saponification. Hence, if the oil shows a difference in the saponification value in thirty minutes and in two hours, which amounts to more than from 1 to 2, terpinyl acetate is almost certainly present. The following table shows the effect of this partial-saponrfication on the two esters and on adulterated oils —... 

Consideration will first be given to the inorganic builders used to produce the base material. The pH values of several commonly used materials are shown in Table 11.1. Hydroxides are the simplest, strongest alkalis and most commonly used. A major effect of hydroxides in cleaning is saponification the conversion of certain oils and greases to water-soluble soap-type materials. Hydroxides also produce solutions of high conductivity, as required for electrocleaning. 

Oil-base (including oil-modified alkyd resin) paint films should not be used in alkaline environments as the paint will deteriorate owing to saponification alkali-resistant coatings are provided by some cellulose ethers, e.g. ethyl cellulose, certain polyurethane, chlorinated rubber, epoxy, p.v.c./ p.v.a. copolymer, or acrylic-resin-based paints. In particular, aluminium and its alloys should be protected by alkali-resistant coatings owing to the detrimental effects of alkali on these metals. 

The saponification process results in about 75 percent soap and 25 percent glycerin. In homemade soaps, the glycerin is left in, as it acts as an emollient (skin softener) and creates a nice feel. In commercial soaps, the glycerin is often removed and sold separately, sometimes showing up in skin moisturizers that remedy soap s skin-drying effects. 

There is a considerable presumption that steric twisting from coplanarity, which diminishes effective transmittal of pi-electron effects, has appreciable effect on X. For example, the X = 1.10 for the phthalide saponification rate (no. 28 of Table III) compared with X=. 89 for the corresponding benzoate saponification rate is probably a reflection of the rigid coplanarity conditions imposed in the former structure. However, the reactions were carried out in differing compositions of H2 0-Et0H solvent, so that a solvent effect may also be involved. 

The combined results of kinetic studies on condensation polymerization reactions and on the degradation of various polymers by reactions which bring about chain scission demonstrate quite clearly that the chemical reactivity of a functional group does not ordinarily depend on the size of the molecule to which it is attached. Exceptions occur only when the chain is so short as to allow the specific effect of one end group on the reactivity of the other to be appreciable. Evidence from a third type of polymer reaction, namely, that in which the lateral substituents of the polymer chain undergo reaction without alteration in the degree of polymerization, also support this conclusion. The velocity of saponification of polyvinyl acetate, for example, is very nearly the same as that for ethyl acetate under the same conditions. ... 

Water-in-oil macroemulsions have been proposed as a method for producing viscous drive fluids that can maintain effective mobility control while displacing moderately viscous oils. For example, the use of water-in-oil and oil-in-water macroemulsions have been evaluated as drive fluids to improve oil recovery of viscous oils. Such emulsions have been created by addition of sodium hydroxide to acidic crude oils from Canada and Venezuela. In this study, the emulsions were stabilized by soap films created by saponification of acidic hydrocarbon components in the crude oil by sodium hydroxide. These soap films reduced the oil/water interfacial tension, acting as surfactants to stabilize the water-in-oil emulsion. It is well known, therefore, that the stability of such emulsions substantially depends on the use of sodium hydroxide (i.e., caustic) for producing a soap film to reduce the oil/water interfacial tension. 

---