Refractive index of materials

Table 3 Refractive Index of Materials Used for Experiments...

The anomalous dispersion observed in ORD spectra arises since the refractive index of material is actually the sum of a real and imaginary part ... 

Birefringent components are used for optical polarization devices such as polarizers, waveplates, and beam splitters. Birefringence means that the refractive index of materials is different in different directions. The refiactive index of a material is related to the molecular polarizability via the Lorentz-Lorenz equation as follows ... 

Measurement of Refractive Indexes. Some of the techniques used to measure refractive indexes are the Becke line method (94), interference microscopy (95,96), Abbe refractometer (40,94,97-99), and ellipsometry (100). The Abbe re-fractometer (Fig. 5) can be used to determine the refractive indexes of materials belonging to all three optical symmetries. Its principle is based on the total reflection phenomenon occurring between a known and unknown isotropic media ... 

Eq. 2.19 is derived assuming that a particle scatters as if it were an opaque circular disc of the same projected area positioned normally to the axis of the beam. Because of this assumption, in the Fraunhofer theory the refractive index of material is irrelevant. Fraunhofer diffraction applies to particles 1) whose... 

Selection of a specific telescope design is, therefore, not straightforward. Large aperture lens systems can become very heavy. The refractive index of materials is usually quite high in the infrared and requires each surface to have multilayer... 

Methylene iodide [75-11-6], CH2I2, also known as diio dome thane, mol wt 267.87, 94.76% I, mp 6.0°C, and bp 181°C, is a very heavy colorless Hquid. It has a density of 3.325 g/mL at 20°C and a refractive index of 1.7538 at 4°C. It darkens in contact with air, moisture, and light. Its solubiHty in water is 1.42 g/100 g H2O at 20°C it is soluble in alcohol, chloroform, ben2ene, and ether. Methylene iodide is prepared by reaction of sodium arsenite and iodoform with sodium hydroxide reaction of iodine, sodium ethoxide, and hydroiodic acid on iodoform the oxidation of iodoacetic acid with potassium persulfate and by reaction of potassium iodide and methylene chloride (124,125). Diiodoform is used for determining the density and refractive index of minerals. It is also used as a starting material in the manufacture of x-ray contrast media and other synthetic pharmaceuticals (qv). 

Antireflection coatings are used over the silicon surface which, without the coating, reflects ca 35% of incident sunlight. A typical coating consists of a single layer of a transparent dielectric material with a refractive index of ca 2, which is between the index of siUcon and ait or cover material. Materials such as titanium dioxide, tantalum pentoxide, Ta20, or siUcon nitride, Si N, ca 0.08-p.m thick are common. The coating and a physically textured... 

The pyrrolines or dihydropyrroles can exist in three isomeric forms 1-pyrroline (3,4-dihyro-2JT-pyrrole [5724-81-2]) (16) is an unstable material that resiniftes upon exposure to air 2-pyrroline (2,3-dihydro-lJT-pyrrole [638-31-3]) (17) is even more unstable only 3-pyrroline (2,5-dihydro-lJT-pyrrole [109-96-6]) (18) is reasonably stable. 3-Pyrroline bods at 91°C and has a density of 0.9097 g/cm and a refractive index of 1.4664. 

In the glass (qv) and ceramic industry (see Ceramics), barite can be used both as a flux, to promote melting at a lower temperature or to increase the production rate, and as an additive to increase the refractive index of glass. The viscosity of barite-containing glass often needs to be raised. Alumina in the form of feldspar is sometimes used. To offset any color produced by iron from the barite addition, more decolorizer may be needed. When properly used, barytes help reduce seed, increase toughness and brilliancy, and reduce annealing time. Barite is also a raw material for the manufacture of other barium chemicals. 

Another classification of detector is the bulk-property detector, one that measures a change in some overall property of the system of mobile phase plus sample. The most commonly used bulk-property detector is the refractive-index (RI) detector. The RI detector, the closest thing to a universal detector in lc, monitors the difference between the refractive index of the effluent from the column and pure solvent. These detectors are not very good for detection of materials at low concentrations. Moreover, they are sensitive to fluctuations in temperature. 

Here, the wavelength of the laser light is A, and is a correction term due to the wavelength dependence of the refractive index of the etalon material ( = 0.034 at 514.5 nm when fused silica etalons are used to achieve the necessary delay, or = 0 when a lens combination is used). The optical correction term Av/v results from the change in refractive index of the window material with shock stress (Barker and Hollenbach, 1970). If the measure-... 

Poly(vinyl acetate) is too soft and shows excessive cold flow for use in moulded plastics. This is no doubt associated with the fact that the glass transition temperature of 28°C is little above the usual ambient temperatures and in fact in many places at various times the glass temperature may be the lower. It has a density of 1.19 g/cm and a refractive index of 1.47. Commercial polymers are atactic and, since they do not crystallise, transparent (if free from emulsifier). They are successfully used in emulsion paints, as adhesives for textiles, paper and wood, as a sizing material and as a permanent starch . A number of grades are supplied by manufacturers which differ in molecular weight and in the nature of comonomers (e.g. vinyl maleate) which are commonly used (see Section 14.4.4)... 

The refractive index of a film or a substrate material can be measured with a sensitivity better than 5 x 10, the best available for non-invasive optical measurement methods, especially for thin films. The extinction coefficient can be measured with almost the same sensitivity, which corresponds to a lower limit of 10-100 cm for the absorption coefficient of the material. 

---