Arsenite sodium

Arylarsonic acids are most readily prepared by the Bart Reaction, in which a diazonium salt in aqueous solution is run into a solution of sodium arsenite in an excess of sodium carbonate. The addition of copper sulphate to the +. ... 

Methylene bromide (CHjBfj) and methylene iodide (CHjIj) are easily prepared by the reduction of bromoform or iodoform respectively with sodium arsenite in alkaline solution ... 

In a 1-litre three-necked flask, mounted on a steam bath and provided respectively with a separatory funnel, mechanical stirrer and double surface condenser, place 165 g. of bromoform (96 per cent.). Add 10 ml. of a solution of sodium arsenite made by dissolving 77 g. of A.R. arsenious oxide and 148 g. of A.R. sodium hydroxide in 475 ml. of water. Warm the mixture gently to start the reaction, and introduce the remainder of the sodium arsenite solution during 30-45 minutes at such a rate that the mixture refluxes gently. Subsequently heat the flask on the steam bath for 3-4 hours. Steam distil the reaction mixture (Fig. 11, 41, 1) and separate the lower layer of methylene bromide (79 g.). Extract the aqueous layer with about 100 ml. of ether a further 3 g. of methylene bromide is obtained. Dry with 3-4 g. of anhydrous calcium chloride, and distil from a Claisen flask with fractionating side arm. The methylene bromide boils constantly at 96-97° and is almost colourless. 

In a 1-litre three-necked flask, fitted with a mechanical stirrer, reflux condenser and a thermometer, place 200 g. of iodoform and half of a sodium arsenite solution, prepared from 54-5 g. of A.R. arsenious oxide, 107 g. of A.R. sodium hydroxide and 520 ml. of water. Start the stirrer and heat the flask until the thermometer reads 60-65° maintain the mixture at this temperature during the whole reaction (1). Run in the remainder of the sodium arsenite solution during the course of 15 minutes, and keep the reaction mixture at 60-65° for 1 hour in order to complete the reaction. AUow to cool to about 40-45° (2) and filter with suction from the small amount of solid impurities. Separate the lower layer from the filtrate, dry it with anhydrous calcium chloride, and distil the crude methylene iodide (131 g. this crude product is satisfactory for most purposes) under diminished pressure. Practically all passes over as a light straw-coloured (sometimes brown) liquid at 80°/25 mm. it melts at 6°. Some of the colour may be removed by shaking with silver powder. The small dark residue in the flask solidifies on cooling. 

Phenylarsonic acid may be obtained from the reaction between phenyl-diazonium chloride and sodium arsenite in the presence of a trace of copper sulphate ... 

The conversion of an aromatic diazonium compound into the corresponding arsonic acid by treatment with sodium arsenite in the presence of a catalyst, such as copper or a copper salt, is called the Bart reaction. A modification of the reaction employs the more stable diazonium fluoborate in place of the diazonium chlorid.i. This is illustrated by the preparation of />-nitrophenylarsonic acid ... 

Concurrently with the preparation of the phenyldiazonium chloride solution, prepare a cold suspension of sodium arsenite. Place 250 ml. of water in a 3-htre round-bottomed flask equipped with a mechanical stirrer. Heat the water to boding, add 125 g. of anhydrous sodium carbonate, and, as soon as the carbonate has dissolved, introduce 62 5 g. of pure arsenious oxide and 3 g. of crystallised copper sulphate with stirring. When all the solids have dissolved, cool the solution with stirring under a stream of tap water until the temperature has fallen to 15°. 

Azoxybenzene is readily prepared by reduction of nitrobenzene in an alkaline medium with dextrose or sodium arsenite ... 

The elements listed in the table of Figure 15.2 are of importance as environmental contaminants, and their analysis in soils, water, seawater, foodstuffs and for forensic purposes is performed routinely. For these reasons, methods have been sought to analyze samples of these elements quickly and easily without significant prepreparation. One way to unlock these elements from their compounds or salts, in which form they are usually found, is to reduce them to their volatile hydrides through the use of acid and sodium tetrahydroborate (sodium borohydride), as shown in Equation 15.1 for sodium arsenite. 

Methylene iodide [75-11-6], CH2I2, also known as diio dome thane, mol wt 267.87, 94.76% I, mp 6.0°C, and bp 181°C, is a very heavy colorless Hquid. It has a density of 3.325 g/mL at 20°C and a refractive index of 1.7538 at 4°C. It darkens in contact with air, moisture, and light. Its solubiHty in water is 1.42 g/100 g H2O at 20°C it is soluble in alcohol, chloroform, ben2ene, and ether. Methylene iodide is prepared by reaction of sodium arsenite and iodoform with sodium hydroxide reaction of iodine, sodium ethoxide, and hydroiodic acid on iodoform the oxidation of iodoacetic acid with potassium persulfate and by reaction of potassium iodide and methylene chloride (124,125). Diiodoform is used for determining the density and refractive index of minerals. It is also used as a starting material in the manufacture of x-ray contrast media and other synthetic pharmaceuticals (qv). 

Where X is Br or Q, the free acids may be obtained by acidification of the alkaline solution, but where X is I, the acids must be isolated as salts to avoid reduction of the arsonic acids by HI. Rather than using alkyl haUdes, alkyl or dialkyl sulfates or alkyl arenesulfonates can be used. Primary alkyl haUdes react rapidly and smoothly, secondary haUdes react only slowly, whereas tertiary haUdes do not give arsonic acids. AHyl haUdes undergo the Meyer reaction, but vinyl hahdes do not. Substituted alkyl haUdes can be used eg, ethylene chlorohydrin gives 2-hydroxyethylarsonic acid [65423-87-2], C2H2ASO4. Arsinic acids, R2AsO(OH), are also readily prepared by substituting an alkaU metal arsonite, RAs(OM)2, for sodium arsenite ... 

Aiomatic aisonic acids aie generally prepared by tiie Bart reaction from an aromatic diazonium salt and sodium arsenite ... 

SolubiHty of carbon dioxide in ethanolamines is affected by temperature, amine solution strength, and carbon dioxide partial pressure. Information on the performance of amines is available in the Hterature and from amine manufacturers. Values for the solubiHty of carbon dioxide and hydrogen sulfide mixtures in monoethanolamine and for the solubiHty of carbon dioxide in diethanolamine are given (36,37). SolubiHty of carbon dioxide in monoethanolamine is provided (38). The effects of catalysts have been studied to improve the activity of amines and provide absorption data for carbon dioxide in both mono- and diethanolamine solutions with and without sodium arsenite as a catalyst (39). Absorption kinetics over a range of contact times for carbon dioxide in monoethanolamine have also been investigated (40). 

Both the equilibria and the enhancement of the coefficients can be improved by additives, of which sodium arsenite is the major one in use, but sodium hypochlorite and small amounts of amines also are effective. Sterically hindered amines as promoters are claimed by Say et al. (Chem. Eng. Prog., 80(10), 72-77 [1984]) to result in 50 percent more capacity than ordinary amine promoters of carbonate solutions. 

The sodium arsenite solution may also be prepared by dissolving 39.6 g. (0.2 mole) of arsenious oxide and 32 g. (0.8 mole) of sodium hydroxide in 600 ml. of water. 

Nitrophenylarsonic acid has been prepared by heating p-nitrobenzenediazonium chloride with arsenious acid in hydrochloric acid, by the action of -nitrobenzenediazonium chloride on sodium arsenite, by the action of sodium arsenite on sodium -nitrobenzeneisodiazo oxide, by the diazotization of -nitro-aniline in acetic acid in the presence of arsenic chloride and cuprous chloride, and by the reaction of -nitrobenzenediazonium borofluoride with sodium arsenite in the presence of cuprous chloride. ... 

SODIUM AMMONIUM VANADATE SODIUM ARSAHILATE SODIUM ARSENATE SODIUM ARSENITE... 

Sodium arsenite can be used to detect the presence of iron sulfide on the metal surface. Iron sulfide is the corrosion product of the reaction between hydrogen sulfide in drilling fluid and iron in the drillpipe. An acid solution of sodium arsenite reacts with the sulfide to form a bright yellow precipitate. 

In the second method, the hypochlorite solution or suspension is titrated against standard sodium arsenite solution this is best done by adding an excess of the arsenite solution and then back-titrating with standard iodine solution. 

The reaction is the reverse of that employed in the standardisation of iodine with sodium arsenite solution (Section 10.113) ... 

Excellent results are obtained by the following method, which is of wider applicability. When excess of standard sodium arsenite solution is treated with hydrogen sulphide solution and then acidified with hydrochloric acid, arsenic(III) sulphide is precipitated ... 

Sodium, D. of as zinc uranyl acetate, (g) 467 by flame photometry, 812 Sodium arsenite solution prepn. of standard, 390... 

Gubits, R.M. Fairhurst, J.L. (1988). c-fos mRNA levels are increased by the cellular stressors, heat shock and sodium arsenite. Oncogene 3, 163-168. 

Azoxy compounds can be obtained from nitro compounds with certain reducing agents, notably sodium arsenite, sodium ethoxide, NaTeH, NaBH4—PhTeTePh, and glucose. The most probable mechanism with most reagents is that one molecule of nitro compound is reduced to a nitroso compound and another to a hydroxylamine 119-42), and these combine (12-51). The combination step is rapid compared to the reduction process. Nitroso compounds can be reduced to azoxy compounds with triethyl phosphite or triphenylphosphine or with an alkaline aqueous solution of an alcohol. ... 

Cerium(IV) Sulfate/Sodium Arsenite/Sulfuric Acid —Methylene Blue —... 

---