Process utilities

Edeleanu process An extraction process utilizing liquid sulphur dioxide for the removal of aromatic hydrocarbons and polar molecules from petroleum fractions. 

The properties of the solids most commonly encountered are tabulated. An important problem arises for petroleum fractions because data for the freezing point and enthalpy of fusion are very scarce. The MEK (methyl ethyl ketone) process utilizes the solvent s property that increases the partial fugacity of the paraffins in the liquid phase and thus favors their crystallization. The calculations for crystallization are sensitive and it is usually necessary to revert to experimental measurement. 

The first process utilizes a bed of nickel catalyst which has been regenerated with hydrogen to reduce the nickel content to metallic form. The finely divided metal then reacts with impurities and retains them in the bed, probably as nickel oxide in the case of oxygen or as physisorbed compounds for other impurities. Periodically, the bed is regenerated at elevated temperature using hydrogen to restore the metallic content. The nickel process can be used and regenerated indefinitely. 

One important class of point-of-use processes utilizes a porous polymer containing reactive metals. Variations in the metal and polymer chemistry are made to optimize the process for different gas appHcations. This is an active area of development and purifiers are available for most of the principal specialty gases. 

Adiponitrile is made commercially by several different processes utilizing different feedstocks. The original process, utilizing adipic acid (qv) as a feedstock, was first commercialized by DuPont in the late 1930s and was the basis for a number of adiponitrile plants. However, the adipic acid process was abandoned by DuPont in favor of two processes based on butadiene (qv). During the 1960s, Monsanto and Asahi developed routes to adiponitrile by the electrodimerization of acrylonitrile (qv). 

Emulsion Process. The emulsion polymerization process utilizes water as a continuous phase with the reactants suspended as microscopic particles. This low viscosity system allows facile mixing and heat transfer for control purposes. An emulsifier is generally employed to stabilize the water insoluble monomers and other reactants, and to prevent reactor fouling. With SAN the system is composed of water, monomers, chain-transfer agents for molecular weight control, emulsifiers, and initiators. Both batch and semibatch processes are employed. Copolymerization is normally carried out at 60 to 100°C to conversions of - 97%. Lower temperature polymerization can be achieved with redox-initiator systems (51). 

M ass Process. In the mass (or bulk) (83) ABS process the polymerization is conducted in a monomer medium rather than in water. This process usually consists of a series of two or more continuous reactors. The mbber used in this process is most commonly a solution-polymerized linear polybutadiene (or copolymer containing sytrene), although some mass processes utilize emulsion-polymerized ABS with a high mbber content for the mbber component (84). If a linear mbber is used, a solution of the mbber in the monomers is prepared for feeding to the reactor system. If emulsion ABS is used as the source of mbber, a dispersion of the ABS in the monomers is usually prepared after the water has been removed from the ABS latex. 

Lubricants, Fuels, and Petroleum. The adipate and azelate diesters of through alcohols, as weU as those of tridecyl alcohol, are used as synthetic lubricants, hydrauHc fluids, and brake fluids. Phosphate esters are utilized as industrial and aviation functional fluids and to a smaH extent as additives in other lubricants. A number of alcohols, particularly the Cg materials, are employed to produce zinc dialkyldithiophosphates as lubricant antiwear additives. A smaH amount is used to make viscosity index improvers for lubricating oils. 2-Ethylhexyl nitrate [24247-96-7] serves as a cetane improver for diesel fuels and hexanol is used as an additive to fuel oil or other fuels (57). Various enhanced oil recovery processes utilize formulations containing hexanol or heptanol to displace oil from underground reservoirs (58) the alcohols and derivatives are also used as defoamers in oil production. 

Commercially, fluorosulfuric acid is made by processes utilizing the product as a solvent. Solutions of HF and SO in fluorosulfuric acid are mixed in stoichiometric quantities, or SO and HF are separately introduced into a stream of fluorosulfuric acid to produce essentially pure HSO F. Some of the product is then recycled (50,51). 

Another hydrogenation process utilizes internally generated hydrogen for hydroconversion in a single-stage, noncatalytic, fluidized-bed reactor (41). Biomass is converted in the reactor, which is operated at about 2.1 kPa, 800°C, and residence times of a few minutes with steam-oxygen injection. About 95% carbon conversion is anticipated to produce a medium heat value (MHV) gas which is subjected to the shift reaction, scmbbing, and methanation to form SNG. The cold gas thermal efficiencies are estimated to be about 60%. 

An alternative polymerization process utilizes a slurry of calcium chloride in NMP as the polymerization medium. The solubiHty of calcium chloride is only 6% at 20°C however, the salt continues to dissolve as conversion of monomers to polymer proceeds and calcium chloride/polyamide complexes are formed. Polymer molecular weight is further increased by the addition of /V, /V- dim ethyl a n i1 in e as an acid acceptor. This solvent system produces fiber-forming polymer of molecular weights comparable to that formed in HMPA/NMP. 

An oxirane process utilizes ethylbenzene to make the hydroperoxide, which then is used to make propylene oxide [75-56-9]. The hydroperoxide-producing reaction is similar to the first step of cumene LPO except that it is slower (2,224,316—318). In the epoxidation step, a-phenylethyl alcohol [98-85-1] is the coproduct. It is dehydrated to styrene [100-42-5]. The reported 1992 capacity for styrene by this route was 0.59 X 10 t/yr (319). The corresponding propylene oxide capacity is ca 0.33 x 10 t/yr. The total propylene oxide capacity based on hydroperoxide oxidation of propylene [115-07-1] (coproducts are /-butyl alcohol and styrene) is 1.05 x 10 t/yr (225). 

The printing of newspapers is conducted at very high speeds, often reaching 3000 feet per miaute. AH three printing processes utilize similar quaHty newsptint which, essentiaHy, is made of groundwood or thermomechanical pulp. Presses are fed a continuous web of newsptint that unwiads from a feed roUer. Inks dry by absorption of Hquid iato the porosity of the substrate. Some evaporation of water ia a flexo pubHcation ink can accelerate the dryiag process. 

Specialty Isocyanates. Acyl isocyanates, extensively used in synthetic appHcations, caimot be direcdy synthesized from amides and phosgene. Reactions of acid haUdes with cyanates have been suggested. However, the dominant commercial process utilizes the reaction of carboxamides with oxalyl chloride [79-37-8]. CycHc intermediates have been observed in these reactions which generally give a high yield of the desired products (86). 

Instmmentation and control guidelines for processes utilizing magnesium hydroxide and other slurries have been outlined (82). An experimental deterrnination of the accuracy of magnetic dow meters for magnesium hydroxide slurries d owing in pipelines (qv) has been reported (83). 

The fourth fully developed membrane process is electrodialysis, in which charged membranes are used to separate ions from aqueous solutions under the driving force of an electrical potential difference. The process utilizes an electrodialysis stack, built on the plate-and-frame principle, containing several hundred individual cells formed by a pair of anion- and cation-exchange membranes. The principal current appHcation of electrodialysis is the desalting of brackish groundwater. However, industrial use of the process in the food industry, for example to deionize cheese whey, is growing, as is its use in poUution-control appHcations. 

Nitromethane also is used in the synthesis of the antiulcer dmg, ranitidine [66357-35-5]. A two-step process utilizing nitromethane, carbon disulfide, potassium hydroxide, and dimethyl sulfate yields l,l-bis(methylthio)-2-nitroethene [13623-94 ] which reacts further to produce ranitidine. 

Computer simulation programs for process design optimization have been developed for the PUREX process utilizing these relationships (22). A subroutine has also been developed which describes the behavior of fission products (23). 

Solution Polymerization. Two types of solution polymerization technologies are used for LLDPE synthesis. One process utilizes heavy solvents the other is carried out in mixtures of supercritical ethylene and molten PE as a polymerization medium. Original solution processes were introduced for low pressure manufacture of PE resins in the late 1950s subsequent improvements of these processes gradually made them economically competitive with later, more advanced technologies. 

Methyl-l-Pen ten e. This olefin is produced commercially by dimeriza tion of propylene in the presence of potassium-based catalysts at 150—160°C and - 10 MPa. Commercial processes utilize several catalysts, such as sodium-promoted potassium carbonate and sodium- and alurninum-promoted potassium hydroxide (12—14) in a fixed-bed reactor. The reaction produces a mixture of C olefins containing 80—85% of 4-methyl- 1-pentene. 

The search for catalyst systems which could effect the 0x0 reaction under milder conditions and produce higher yields of the desired aldehyde resulted in processes utilizing rhodium. Oxo capacity built since the mid-1970s, both in the United States and elsewhere, has largely employed tertiary phosphine-modified rhodium catalysts. For example, over 50% of the world s butyraldehyde (qv) is produced by the LP Oxo process, technology Hcensed by Union Carbide Corporation and Davy Process Technology. 

Insofar as they are used to purify other products, several processes used in the refinery fall under the classification of dewaxing processes however, such processes must also be classified as wax production processes (2). Most commercial dewaxing processes utilize solvent dilution, chilling to crystallize the wax, and filtration (28). The MEK process (methyl ethyl ketone—toluene solvent) is widely used. Wax crystals are formed by chilling through the walls of scraped surface chillers, and wax is separated from the resultant wax—oil—solvent slurry by using fliUy enclosed rotary vacuum filters. 

Air-Suspension Coa.ting. The Wurster process utilizes a cylindrical chamber in which the cores are suspended in a controlled stream of air. Film coatings are appHed by introducing the coating solution into the airstream, where the solvent evaporates quickly. The process is much quicker than film coating however, care must be taken to avoid destmction of the cores by attrition in the air stream. 

Adequate yields in this reaction requite extremely efficient removal of HCI otherwise CH Cl is formed. Some commercial processes utilize catalytic reactions of epoxy with POCl (48) ... 

Transesterification. There has been renewed interest in the transesterification process for preparation of polycarbonate because of the desire to transition technology to environmentally friendly processes. The transesterification process utilizes no solvent during polymerization, producing neat polymer direcdy and thus chlorinated solvents may be entirely eliminated. General Electric operates a polycarbonate plant in Chiba, Japan which produces BPA polycarbonate via this melt process. 

---