Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Polyethylene-nitrile rubber

Phenylene oxide-based resins (Noryl ) epoxy, polyisocyanate, polyvinyl butyral, nitrile rubber, neoprene rubber, polyurethane rubber, polyvinyUdene chloride, and acrylic. Polyethylene-nitrile rubber, polyisobutylene rubber, flexible epoxy, nitrile-phenolic, and water-based (emulsion) adhesives. Polystyrene for these foams (expanded polystyrene (EPS)), aromatic solvent adhesives (e.g., toluol) can cause collapse of the foam cell walls. For this reason, it is advisable to use either 100% solids adhesives or water-based adhesives based on SBR or polyvinyl acetate. Specific adhesives recommended include urea-formaldehyde, epoxy, polyester-isocyanate, polyvinyl acetate, vinyl chloride-vinyl acetate copolymer, and reclaim rubber. Polystyrene foam can be bonded satisfactorily with any of the following general adhesive types ... [Pg.152]

Polyethylene-nitrile rubber, polyisobutylene rubber, flexible epoxy, nitrile-phenolic, and water-based (emulsion) adhesives... [Pg.254]

At one time butadiene-acrylonitrile copolymers (nitrile rubbers) were the most important impact modifiers. Today they have been largely replaced by acrylonitrile-butadiene-styrene (ABS) graft terpolymers, methacrylate-buta-diene-styrene (MBS) terpolymers, chlorinated polyethylene, EVA-PVC graft polymers and some poly acrylates. [Pg.341]

If polypropylene is too hard for the purpose envisaged, then the user should consider, progressively, polyethylene, ethylene-vinyl acetate and plasticised PVC. If more rubberiness is required, then a vulcanising rubber such as natural rubber or SBR or a thermoplastic polyolefin elastomer may be considered. If the material requires to be rubbery and oil and/or heat resistant, vulcanising rubbers such as the polychloroprenes, nitrile rubbers, acrylic rubbers or hydrin rubbers or a thermoplastic elastomer such as a thermoplastic polyester elastomer, thermoplastic polyurethane elastomer or thermoplastic polyamide elastomer may be considered. Where it is important that the elastomer remain rubbery at very low temperatures, then NR, SBR, BR or TPO rubbers may be considered where oil resistance is not a consideration. If, however, oil resistance is important, a polypropylene oxide or hydrin rubber may be preferred. Where a wide temperature service range is paramount, a silicone rubber may be indicated. The selection of rubbery materials has been dealt with by the author elsewhere. ... [Pg.896]

TPEs from blends of rubber and plastics constitute an important category of TPEs. These can be prepared either by the melt mixing of plastics and rubbers in an internal mixer or by solvent casting from a suitable solvent. The commonly used plastics and rubbers include polypropylene (PP), polyethylene (PE), polystyrene (PS), nylon, ethylene propylene diene monomer rubber (EPDM), natural rubber (NR), butyl rubber, nitrile rubber, etc. TPEs from blends of rubbers and plastics have certain typical advantages over the other TPEs. In this case, the required properties can easily be achieved by the proper selection of rubbers and plastics and by the proper change in their ratios. The overall performance of the resultant TPEs can be improved by changing the phase structure and crystallinity of plastics and also by the proper incorporation of suitable fillers, crosslinkers, and interfacial agents. [Pg.634]

ATBN - amine terminated nitrile rubber X - Flory Huggins interaction parameter CPE - carboxylated polyethylene d - width at half height of the copolymer profile given by Kuhn statistical segment length DMAE - dimethyl amino ethanol r - interfacial tension reduction d - particle size reduction DSC - differential scanning calorimetry EMA - ethylene methyl acrylate copolymer ENR - epoxidized natural rubber EOR - ethylene olefin rubber EPDM - ethylene propylene diene monomer EPM - ethylene propylene monomer rubber EPR - ethylene propylene rubber EPR-g-SA - succinic anhydride grafted ethylene propylene rubber... [Pg.682]

The ductility of GRT-polyethylene blends drastically decreases at ground rubber concentration in excess of 5%. The inclusion of hnely ground nitrile rubber from waste printing rollers into polyvinyl chloride (PVC) caused an increase in the impact properties of the thermoplastic matrix [76]. Addition of rubber powder that is physically modihed by ultrasonic treatment leads to PP-waste ethylene-propylene-diene monomer (EPDM) powder blends with improved morphology and mechanical properties [77]. [Pg.1050]

Butyl Rubber and Halo-Butyl Rubber Ethylene Propylene Rubber (q) Hard Rubber (Ebonite) (h) Soft Natural Rubber (h) Neoprene (i) Nitrile Rubber Chlorosulphonated Polyethylene Polyurethane Rubber (v) Silicone Rubbers (k)... [Pg.930]

Plastics and elastomers Degrades chlorinated polyethylene, neoprene, nitrile rubber, polysulfide, polyurethane... [Pg.46]

Of the remaining materials in Table IV, only Viton, neoprene rubber latex,poly(vinyl alcohol), butyl rubber, and butyl-coated nylon exhibited at least a 20-min breakthrough time forl,2 dichloro-ethane permeation to occur. The nitrile rubber latex, cement dipped nitrile rubber, polyethylene (medium density), and surgical rubber latex were all penetrated by 1,2-dichloroethane in less than 3 min and would be of little use in situations requiring the garment to be in constant contact with 1,2-dichloroethane. From the above, butyl rubber or Viton appear to be the best materials to protect the worker against 1,2-dichloroethane, but because of apparent lot-to-lot variations(20) in butyl properties, Viton appears to be the best suited material of these studies to protect the worker from this chemical. [Pg.252]

Other copolymers that are used instead of nitrile rubber are, for instance, chlorinated polyethylene which, in combination with PVC, gives the commercial product, Hostalit Z, of Farbwerke Hoechst. [Pg.98]

Elastomers, synthetic -acrylic elastomers [ELASTOMERS, SYNTHETIC - ACRYLIC ELASTOMERS] (Vol 8) -butyl rubber [ELASTOMERS, SYNTHETIC - BUTYL RUBBER] (Vol 8) -chlorosulfonated polyethylene [ELASTOMERS, SYNTHETIC - CHLOROSULFONATED POLYETHYLENE] (Vol 8) -ethylene-acrylic elastomers [ELASTOMERS, SYNTHETIC - ETHYLENE-ACRYLIC ELASTOMERS] (Vol 8) -ethylene-propylene-diene rubber [ELASTOMERS,SYNTHETTC - ETHYLENE-PROPYLENE-DIENE RUBBER] (Vol 8) -fluorocarbon elastomers [ELASTOMERS, SYNTHETIC - FLUOROCARBON ELASTOMERS] (Vol 8) -nitrile rubber [ELASTOMERS, SYNTHETIC - NITRILE RUBBER] (Vol 8) -phosphazenes [ELASTOMERS, SYNTHETIC - PHOSPHAZENES] (Vol 8) -polybutadiene [ELASTOMERS, SYNTHETIC - POLYBUTADIENE] (Vol 8) -polychloroprene [ELASTOMERS, SYNTHETIC - POLYCHLOROPRENE] (Vol 8) -polyethers (ELASTOMERS, SYNTHETIC - POLYETHERS] (Vol 8) -polyisoprene [ELASTOMERSSYNTHETTC - POLYISOPRENE] (Vol 9) -survey [ELASTOMERS, SYNTHETIC - SURVEY] (Vol 8)... [Pg.354]

The most widely used synthetic rubber is styrene-butadiene rubber (SBR) (Fig. 1). Other commonly used elastomers are polybutadiene, polyethylene-propylene, butyl rubber, neoprene, nitrile rubbers, and polyisoprene. [Pg.451]

Another contrarian, DSM in the Netherlands, had been a state-owned company before it became privatized, a process that began in 1989 and was completed in 1996. From its past it had inherited positions in fertilizers, industrial chemicals, and such intermediates as melamine and caprolactam as well as polyolefins, with access to basic olefins through its own crackers in Geleen, Netherlands. In 1997 DSM acquired the polyethylene and polypropylene operations of FIuls (VEBA) with the Gelsenkirchen site. The company had also diversified into elastomers, having purchased in the United States the Copolymer Rubber and Chemical Corporation, which contributed to DSM s expansion into the fields of ethylene propylene, styrene butadiene, and nitrile rubbers. DSM is also a supplier of industrial resins and engineering... [Pg.60]

Polymers from this class can be used for different practical purposes. For example, poly(ethylene-co-carbon monoxide) has better barrier properties for food packaging material than polyethylene, which is permeable for hydrophobic compounds used as flavors. Other copolymers can be used as plasticizers for nitrile rubber. [Pg.415]

A number of manufactured products comprising thermoplastics (polyethylene, polyvinylchloride, polyamides,. ..) or elastomers (natural rubber, nitrile rubber, ethylene propylene rubber, silicones) are processed by cross-linking to improve their performances in insulated electric wires and cables, multilayered films for cooking pouches, shape memory tubes, pressure resistant water pipes, expandable foams, automotive parts exposed to motor... [Pg.141]

Property Natural Rubber Butyl Rubber EPDM rubber Chloroprene rubber Nitrile rubber Silicone rubber Chloro sulfon ated polyethylene rubber... [Pg.142]

See other pages where Polyethylene-nitrile rubber is mentioned: [Pg.108]    [Pg.108]    [Pg.54]    [Pg.555]    [Pg.44]    [Pg.236]    [Pg.242]    [Pg.252]    [Pg.252]    [Pg.258]    [Pg.265]    [Pg.329]    [Pg.8]    [Pg.96]    [Pg.194]    [Pg.600]    [Pg.40]    [Pg.435]    [Pg.435]    [Pg.142]    [Pg.2720]    [Pg.228]    [Pg.128]    [Pg.220]    [Pg.819]    [Pg.884]    [Pg.925]   
See also in sourсe #XX -- [ Pg.152 ]



SEARCH



Nitrile rubber

Polyethylene rubbers

Polyethylene-nitrile rubber recommended adhesives

© 2024 chempedia.info