Polyacrylamide monomer

Figure 1. Chemical structure of polyacrylic acid and polyacrylamide monomers and sodium dodecylsulfonate.

Hydrolysis of cationic polyacrylamides prepared from copolymeri2ation of acrylamide and cationic ester monomer can occur under very mild conditions. A substantial loss in cationicity can cause a significant loss in performance in many apphcations. Copolymers [69418-26-4] of acrylamide and acryloxyethyltrimethylammonium chloride [44992-01 -0] CgH gN02(Cl), for instance, lose cationicity rapidly at alkaline pH (37). 

Solution Polymerization. Plant scale polymerizations ia water are conducted either adiabaticaHy or isotherm ally. Molecular weight control, exotherm control, and reduction of residual monomer are factors which limit the types of initiators employed. Commercially available high molecular weight solution polyacrylamides are usually manufactured and sold at about 5% soHds so that the viscosities permit the final product to be pumped easily. 

Microemulsion Polymerization. Polyacrylamide microemulsions are low viscosity, non settling, clear, thermodynamically stable water-in-od emulsions with particle sizes less than about 100 nm (98—100). They were developed to try to overcome the inherent settling problems of the larger particle size, conventional inverse emulsion polyacrylamides. To achieve the smaller microemulsion particle size, increased surfactant levels are required, making this system more expensive than inverse emulsions. Acrylamide microemulsions form spontaneously when the correct combinations and types of oils, surfactants, and aqueous monomer solutions are combined. Consequendy, no homogenization is required. Polymerization of acrylamide microemulsions is conducted similarly to conventional acrylamide inverse emulsions. To date, polyacrylamide microemulsions have not been commercialized, although work has continued in an effort to exploit the unique features of this technology (100). 

Before polyacrylamides are sold, the amount of residual acrylamide is determined. In one method, the monomer is extracted from the polymer and the acrylamide content is determined by hplc (153). A second method is based on analysis by cationic exchange chromatography (154). For dry products the particle si2e distribution can be quickly determined by use of a shaker and a series of test sieves. Batches with small particles can present a dust ha2ard. The percentage of insoluble material is determined in both dry and emulsion products. 

The principal monomer is acrylamide [79-06-17, where R = H and R = NH2, made by the hydrolysis of acrylonitrile. The homopolymer [9003-05-8] of acrylamide, which in theory has no electrical charge, has some use as a flocculant however, the majority of acrylamide-based flocculants are copolymers with acryHc monomers containing charged functional groups, such as those shown in Figure 1, or polymers containing functional groups formed by modification of acrylamide homopolymers or copolymers (Fig. 2). The chemistry of polyacrylamides has been reviewed by several authors (18—20) (see... 

Size Isomers. In solution, hGH is a mixture of monomer, dimer, and higher molecular weight oligomers. Furthermore, there are aggregated forms of hGH found in both the pituitary and in the circulation (16,17). The dimeric forms of hGH have been the most carefully studied and there appear to be at least three distinct types of dimer a disulfide dimer connected through interchain disulfide bonds (8) a covalent or irreversible dimer that is detected on sodium dodecylsulfate- (SDS-)polyacrylamide gels (see Electroseparations, Electrophoresis) and is not a disulfide dimer (19,20) and a noncovalent dimer which is easily dissociated into monomeric hGH by treatment with agents that dismpt hydrophobic interactions in proteins (21). In addition, hGH forms a dimeric complex with ( 2). Scatchard analysis has revealed that two ions associate per hGH dimer in a cooperative... 

Examples of photothermoplasts include polyacrylates, polyacrylamides, polystyrenes, polycarbonates, and their copolymers (169). An especially well-re searched photothermoplast is poly(methyl methacrylate) (PMMA), which is blended with methyl methacrylate (MMA) or styrene as a monomer, and titanium-bis(cyclopentadienyl) as a photoinitiator (170). 

Polyacrylamide Electrophoresis. Polyacrylamide gels are synthesized through the combination of acrylamide [79-60-1] (qv), CH2=CHC0NH2, monomer and a cross-linking comonomer (see Acrylamide POLYMERS). Typically, the cross-linking comonomer of choice is... 

N,]S2-diaHyltartardiamide (DATD) [58477-85-3] (37). The cross-linking of polymerized monomer with the comonomer is what controls the pore size of the gel polymer mesh. This level of pore size control makes polyacrylamide gel electrophoresis an effective analytical tool. 

Suspension polymerization of water-insoluble monomers (e.g., styrene and divinylbenzene) involves the formation of an oil droplet suspension of the monomer in water with direct conversions of individual monomer droplets into the corresponding polymer beads. Preparation of beaded polymers from water-soluble monomers (e.g., acrylamide) is similar, except that an aqueous solution of monomers is dispersed in oil to form a water-in-oil (w/o) droplet suspension. Subsequent polymerization of the monomer droplets produces the corresponding swollen hydrophilic polyacrylamide beads. These processes are often referred to as inverse suspension polymerization. 

Beaded acrylamide resins (28) are generally produced by w/o inverse-suspension polymerization. This involves the dispersion of an aqueous solution of the monomer and an initiator (e.g., ammonium peroxodisulfates) with a droplet stabilizer such as carboxymethylcellulose or cellulose acetate butyrate in an immiscible liquid (the oil phase), such as 1,2-dichloroethane, toluene, or a liquid paraffin. A polymerization catalyst, usually tetramethylethylenediamine, may also be added to the monomer mixture. The polymerization of beaded acrylamide resin is carried out at relatively low temperatures (20-50°C), and the polymerization is complete within a relatively short period (1-5 hr). The polymerization of most acrylamides proceeds at a substantially faster rate than that of styrene in o/w suspension polymerization. The problem with droplet coagulation during the synthesis of beaded polyacrylamide by w/o suspension polymerization is usually less critical than that with a styrene-based resin. 

Polymerization in aqueous solution of acrylamide can also be fulfilled in thin layers (up to 20 mm) applied on a steel plate or a traveling steel band. Polymerization is initiated by persulfates, redox system, UV or y radiation. Polymerization proceeds in isothermal conditions as the heat of polymerization is dissipated in the environment and, additionally, absorbed by the steel carrier. Nonadhesion of the polymer to the carrier is ensured by the addition of glycerol to isopropyl alcohol or by precoating the steel band with a film based on fluor-containing polymers. This makes polymerization possible at a high concentration of the monomer (20-45%) and in a wider process temperature range. This film of polyacrylamide is removed from the band, crushed, dried, and packed. 

To maintain a high polymerization rate at high conversions, reduce the residual amount of the monomer, and eliminate the adverse process of polyacrylamide structurization, polymerization is carried out in the adiabatic mode. An increase in temperature in the reaction mixture due to the heat evolved in the process of polymerization is conductive to a reduction of the system viscosity even though the polymer concentration in it rises. In this case, the increase in flexibility and mobility of macromolecules shifts the start of the oncoming gel effect into the range of deep transformation or eliminates it completely. 

Radical copolymerization is used in the manufacturing of random copolymers of acrylamide with vinyl monomers. Anionic copolymers are obtained by copolymerization of acrylamide with acrylic, methacrylic, maleic, fu-maric, styrenesulfonic, 2-acrylamide-2-methylpro-panesulfonic acids and its salts, etc., as well as by hydrolysis and sulfomethylation of polyacrylamide Cationic copolymers are obtained by copolymerization of acrylamide with jV-dialkylaminoalkyl acrylates and methacrylates, l,2-dimethyl-5-vinylpyridinum sulfate, etc. or by postreactions of polyacrylamide (the Mannich reaction and Hofmann degradation). Nonionic copolymers are obtained by copolymerization of acrylamide with acrylates, methacrylates, styrene derivatives, acrylonitrile, etc. Copolymerization methods are the same as the polymerization of acrylamide. 

Omstein [276] developed a model for a rigidly organized gel as a cubic lattice, where the lattice elements consist of the polyacrylamide chains and the intersections of the lattice elements represent the cross-links. Figure 7 shows the polymer chains arranged in a cubic lattice as in Omstein s model and several other uniform pore models for comparison. This model predicted r, the pore size, to be proportional to I/Vt, where T is the concentration of total monomer in the gel, and he found that for a 7.5% T gel the pore size was 5 nm. Although this may be more appropriate for regular media, such as zeolites, this model gives the same functional dependence on T as some other, more complex models. 

Kinetic gelation simulations seek to follow the reaction kinetics of monomers and growing chains in space and time using lattice models [43]. In one example, Bowen and Peppas [155] considered homopolymerization of tetrafunctional monomers, decay of initiator molecules, and motion of monomers in the lattice network. Extensive kinetic simulations such as this can provide information on how the structure of the gel and the conversion of monomer change during the course of gelation. Application of this type of model to polyacrylamide gels and comparison to experimental data has not been reported. 

Chiari, M Micheletti, C Nesi, M Fazio, M Righetti, PG, Towards New Formulations for Polyacrylamide Matrices A-Acryloylaminoethoxyethanol, a Novel Monomer Combining High Hydrophilicity with Extreme Hydrolytic Stability, Electrophoresis 15, 177, 1994. Chiari, M Righetti, PG, New Types of Separation Matrices for Electrophoresis, Electrophoresis 16, 1815, 1995. 

Righetti, PG Caglio, S, On the Kinetics of Monomer Incorporation into Polyacrylamide Gels, as Investigated by Capillary Zone Electrophoresis, Electrophoresis 14, 573, 1993. 

Synthetic polymers and natural polymers suitable for drilling muds are listed in Tables 1-7 and 1-8, respectively. Polyacrylamides are eventually hydrolyzed in the course of time and temperature. This leads to a lack of tolerance toward electrolyte contamination and to a rapid degradation inducing a loss of their properties. Modifications of polyacrylamide structures have been proposed to postpone their thermal stability to higher temperatures. Monomers such as AMPS or sulfonated styrene/maleic anhydride can be used to prevent acrylamide comonomer from hydrolysis [92]. 

---