Poison Applicator

Over the course of history, the ancients discovered extraordinarily diverse medicinal and poison applications for extracts from the natural world. In the last hundred years, most of the active principles of these extracts have been isolated and identified and many shown to be structural variants of the steroid molecule (I). 

Rosano TG, Hubbard JD, Meola JM, Swift TA. Fatal strychnine poisoning application of gas chromatography and tandem mass spectrometry. J Anal Toxicol 2000 24(7) 642-7. 

Rosano, T.G., Hubbard, J.D., Meola, J.M., and Swift, T.A. (2000) Fatal strychnine poisoning Application of gas chromatography and tandem mass spectrometry. Journal of Analytical Toxicology, 24,642-647. 

CHjSH CHSH-CHjOH. Usually obtained as an oil, m.p. 77 C. Developed as an antidote to poisoning by organic arsenicals by external application, it is of use in poisoning by Hg, Cu, Zn, Cd but not Pb. It acts by forming a chelate with the metal and so removing it from the system. 

Both chloramine-T and dichloramine-T have marked antiseptic properties, chloramine-T being most frequently used because of its solubility in water. Aqueous solutions of chloramine-T can be used either for external application, or for internal application to the mouth, throat, etc, as chloramine-T in moderate quantities is non-toxic its aqueous solution can also be effectively used when the skin has come in contact with many of the vesicant liquid poison-gases, as the latter are frequently organic sulphur or arsenic derivatives which combine with or are oxidised by chloramine-T and are thus rendered harmless. 

Using 2eohte catalysts, the NO reduction takes place inside a molecular sieve ceramic body rather than on the surface of a metallic catalyst (see Molecularsieves). This difference is reported to reduce the effect of particulates, soot, SO2/SO2 conversions, heavy metals, etc, which poison, plug, and mask metal catalysts. ZeoHtes have been in use in Europe since the mid-1980s and there are approximately 100 installations on stream. Process applications range from use of natural gas to coal as fuel. Typically, nitrogen oxide levels are reduced 80 to 90% (37). 

Subsection B This subsection contains rules pertaining to the methods of fabrication of pressure vessels. Part UW is applicable to welded vessels. Service restric tions are defined. Lethal service is for lethal substances, which are defined as poisonous gases or liquids of such a nature that a very small amount of the gas or the vapor of the liquid mixed or unmixed with air is dangerous to life when inhaled. It is stated that it is the user s responsibility to advise the designer or manufacturer if the service is lethal. All vessels in lethal service shall have all butt-welded joints fully radiographed, and when practical, joints shall be butt-welded. All vessels fabricated of carbon or low-aUoy steel shall be postweld-heat-treated. 

Metal oxides, sulfides, and hydrides form a transition between acid/base and metal catalysts. They catalyze hydrogenation/dehydro-genation as well as many of the reactions catalyzed by acids, such as cracking and isomerization. Their oxidation activity is related to the possibility of two valence states which allow oxygen to be released and reabsorbed alternately. Common examples are oxides of cobalt, iron, zinc, and chromium and hydrides of precious metals that can release hydrogen readily. Sulfide catalysts are more resistant than metals to the formation of coke deposits and to poisoning by sulfur compounds their main application is in hydrodesulfurization. 

Mostly applicable to activities, e.g. reverse flow, chemical reaction. Can also be applied to substances, e.g. poison instead of antidote, D instead of L optical isomers... 

Washing light hydrocarbons with water is a common refinery practice. It finds application on the feed to catalytic polymerization plants. It is used to remove any entrained caustic from the mercaptan removal facilities as well as any other impurities such as amines which tend to poison the polymerization catalyst. Another use for water wash is in alkylation plants to remove salts from streams, where heating would tend to deposit them out and plug up heat exchanger surfaces. Water washing can be carried out in a mixer- settler, or in a tower if more intimate contacting is necessary. 

Advantages (a) Can treat dilute streams and complex mixtures of organic compounds. (b) Can treat gases containing particulates, water, or catalyst poisons. (c) Simple operating concept. (d) Wide applicability (e) Compact, light units available. 

In order to reduce or eliminate off-line sample preparation, multidimensional chromatographic techniques have been employed in these difficult analyses. LC-GC has been employed in numerous applications that involve the analysis of poisonous compounds or metabolites from biological matrices such as fats and tissues, while GC-GC has been employed for complex samples, such as arson propellants and for samples in which special selectivity, such as chiral recognition, is required. Other techniques include on-line sample preparation methods, such as supercritical fluid extraction (SFE)-GC and LC-GC-GC. In many of these applications, the chromatographic method is coupled to mass spectrometry or another spectrometiic detector for final confirmation of the analyte identity, as required by many courts of law. 

The concentration of a solute has a considerable effect on the viscosity of the fluid and so on the surface convective resistance to heat flow. There is little published data on these effects, so applications need to be checked from basic principles. Industrial alcohol (comprising ethyl alcohol with a statutory addition of methyl alcohol to render it poisonous) may be used as a secondary refrigerant, either at 100% concentration or mixed with water. The fluid has a low viscosity and good heat transfer, but is nowlittle used on account of its toxicity and the fire risk in high concentrations. Other nonfreeze heat transfer fluids are used in specialist trades. 

Special applications are often governed by different priorities as already discussed in relation to golf carts, the low water loss and the delay in antimony poisoning in heavy-duty service of a forklift are of eminent importance, with the result that rubber separators remain the preferred product there. Submarine batteries offer a different... 

This paper surveys the field of methanation from fundamentals through commercial application. Thermodynamic data are used to predict the effects of temperature, pressure, number of equilibrium reaction stages, and feed composition on methane yield. Mechanisms and proposed kinetic equations are reviewed. These equations cannot prove any one mechanism however, they give insight on relative catalyst activity and rate-controlling steps. Derivation of kinetic equations from the temperature profile in an adiabatic flow system is illustrated. Various catalysts and their preparation are discussed. Nickel seems best nickel catalysts apparently have active sites with AF 3 kcal which accounts for observed poisoning by sulfur and steam. Carbon laydown is thermodynamically possible in a methanator, but it can be avoided kinetically by proper catalyst selection. Proposed commercial methanation systems are reviewed. 

---