Performances, RAM

Availability, in general, is defined as the ability of the plant/equipment to perform its required function over a stated period of time. Maintainability is the probability that a failed item can be restored to operation effectiveness within a given period of time when repair action is performed as per the specified procedure (Smith, 2011). Software is available for performing RAM studies. For smaller projects, spreadsheets can be used. Reliability and process safety are interlinked, and so combined RAM and safety (RAMS) studies can be performed with the RAMS software (Sikos and Klemes, 2010). It considers many factors affecting the plant performance such as equipment performance, redundancy, demand requirements and logistics. RAM analysis is based on statistical failure data such as mean time between failures (MTBF), mean time to repair (MTTR), mean time to failure (MTTF) and mean down time (MDT). Wherever possible, failure data available within the company should be used for RAM/RAMS study. If not, typical failure data available in the literature/software can be used. 

In Lakestani (10) modelling work performed within the PISC III project is validated against experiments. Figure 1 shows the pulse echo response from the lower edge of a 10 mm vertical strip-like crack at centre depth 55 mm. The probe has the size 20 mm by 22 ram, is of SV type with angle 45 and has centre frequency 2.2 MHz and an assumed bandwidth of 2 MHz. The calibration is perfomed by a side-drilled hole of diameter 9.5 mm and centre depth 60 mm (the... 

Becker et al. (11) have performed extensive experiments on surface-breaking cracks, tilting both the cracks or the back-side. The cracks are like a half ellipse, but could presumably be reasonably approximated by a strip-like crack. Figure 3 shows a comparison between the experiments and UTDefect for a 2.54 mm crack with varying tilt. The thickness of the plate with the crack is 15.24 ram. The probe is a circular 45 SV probe with frequency 2.25 MHz and diameter 12.7 mm. The experiments are calibrated with a notch but this is presently not... 

The Pascal code was updated to handle four channels. To follow the inspection speed all raw measuring data were captured and stored in the computer. All data for one coil could be stored in the computer memory (RAM) and transferred to the disk before inspection of the next coil. Evaluation of the data could be performed on-line or later using a special evaluation program. 

Advanced composites and fiber-reinforced materials are used in sailcloth, speedboat, and other types of boat components, and leisure and commercial fishing gear. A ram id and polyethylene fibers are currentiy used in conveyer belts to collect valuable offshore minerals such as cobalt, uranium, and manganese. Constmction of oil-adsorbing fences made of high performance fabrics is being evaluated in Japan as well as the constmction of other pollution control textile materials for maritime use. For most marine uses, the textile materials must be resistant to biodeterioration and to a variety of aqueous pollutants and environmental conditions. 

Electronic Controllers Almost all of the electronic process controllers used todav are microprocessor-based devices. These processor-based controllers contain, or have access to, inpuLoutput (I/O) interface electronics that allow various types of signals to enter and leave the controller s processor. The controller, depending on its type, uses sufficient read-only-memoiy (ROM) and read/write-accessible-memoiy (RAM) to perform the controller function. 

In the multiple-retori. stoker, rams feed coal to the top of sloping grates between banks of tuyeres. Auxiliary small sloping rams perform... 

To ensure consistency, the two critical areas for control specific to injection molding are shot size control and temperature control on the injection system, i.e., screw portion for the reciprocating screw machines, and both the screw and ram sections for the screw/ram machines. As mentioned previously, for temperature and cure control, the use of microprocessor controls has significantly improved the performance of injection molding machines, including control of the shot size. 

A die stamping was produced in just one action. Stock (2) was fed into die (1) and the deformation to obtain a cup was performed by a stamp (3) which moved in a sleeve (4) driven by a piston of a hydraulic cylinder. The strain obtained was measured with strain gauge (5). The temperature of the deformed alloy was maintained by heating device (7) and controlled with sensor (8). After the deformation was completed shedder (9) driven by a piston (10) of hydraulic cylinder (11) ejected the cup. The whole press ram rested upon base (12). 

See also Acid Ram Air Quality, Indoor Atmosphere Automobile Performance Climatic Effects Emission Control, Vehicle Emission Control, Power Plant Environmental Economics Environmental Problems and Energy Use Gasoline and Additives Transportation, Evolution of Energy Use and Turbines, Gas. 

Figure 5. Performance of RAM AA cells as a function of the depth of discharge (DOD) recharging is done after each discharge. For an explanation of these example, see the text.

At low temperatures down to -20 °C RAM cells function but their performance is decreased the decrease is more severe for higher rates. At higher temperatures up to 50 °C the low-rate performance is un-... 

Time, pressure, and temperature controls indicate whether the performance requirements of a molded product are being met. The time factors include the rate of injection, duration of ram pressure, time of cooling, time of piastication, and screw RPM. Pressure requirement factors relate to injection high and low pressure cycles, back pressure on the extruder screw, and pressure loss before the plastic enters the cavity which can be caused by a variety of restrictions in the mold. The temperature control factors are in the mold (cavity and core), barrel, and nozzle, as well as the melt temperature from back pressure, screw speed, frictional heat, and so on in the plasticator. 

The first example of microwave-promoted solid-phase methodology in heterocyclic chemistry was the arylation of thiophene and indole via Suzuki couplings on TentaGel S RAM resin, as demonstrated by Hallberg and coworkers in 1996, before temperature- and pressure-controlled microwave instruments were even available [189]. Three years later Schotten and coworkers presented analogous but aqueous Suzuki couplings of 5-bromo-thiophene anchored to PEG soluble support via a carboxylic function at its C-2 position [116]. Unfortunately, this work was performed in a do-... 

FIGURE 9.6 The peptide and small protein map from a 100 pL human plasma injection. Columns sample preparation SCX RAM analytical column chromolith performance RP-18, 100 x 0.1 mm I.D. Minute fractions were analyzed using MALDI-TOF MS. Fraction numbers correspond to the time scale. Dot size is related to signal intensity. 

The same authors performed a microwave assisted Stille reaction on the Rink amide (RAM) Tentagel polymer-tethered 4-iodobenzoic acid [5 b]. Successful palladium-catalyzed coupling of heteroaryl boronic acid with anchored 4-iodobenzoic acid enabled both >99% conversion of the starting material within 3.8 min (45 W) and a minimal decomposition of the solid support. The coupling reactions were realized in a mixture of polar solvents (H20-EtOH-DME, 2.5 1.5 6). 

---