Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Parameter limits

The computational process of analysis is hidden from the user, and visually the analysis is conducted in terms of M-02-91 or R6 [6] assessment procedure On the basis of data of stress state and defect configuration the necessary assessment parameters (limit load, stress intensity factor variation along the crack-like defect edge) are determined. Special attention is devoted to realization of sensitivity analysis. Effect of variations in calculated stress distribution and defect configuration are estimated by built-in way. [Pg.196]

Electric motors above 5,000 hp are custom-designed for the specific application, taking into consideration compressor characteristics and the power system parameter limitations. [Pg.258]

Can the plant pressure or the inventory of process materials, or both, be reduced effectively and safely in a major emergency Are the operating parameter limits which require remedial action, known and measured, e.g. temperature, pressure, flow, concentration ... [Pg.399]

Basket-type reactor (CSTR) for gas-phase reactions) High temperature, high pressure catalytic processes High transport rates, easy variation of parameters Limited particle size, high equipment cost, difficult to operate under a wide range of conditions without creating flow maldistribution... [Pg.307]

Parameter Limit Values Frontside Rearside Unit... [Pg.268]

These results indicate that our scaled-up model ecosystems are more useful for studying system processes than processes that function in individual components of the environment. In this regard, a preliminary large scale ecosystem study could be very useful to indicate parameter limits such as overall degradation rates and likely concentrations of parent compounds plus metabolites over time. Such information would be useful in the design of metabolic studies in various components of the ecosystem. In addition, the large scale ecosystem study could also be used to determine if processes derived under laboratory conditions continue to function and/or predominate when combined in a complex system. [Pg.215]

Parameter Limit assay DS main compound Limit assay DP main compound Limit purity and chiral methods Comments... [Pg.85]

If absolute minimum time and minimal temperature parameters are not used during the componentry challenge mns, manufacturing order parameter limits must reflect the parameters used during these runs. [Pg.282]

The relation of the two-parameter limit to lattice models of polymer configurations has been discussed in [BD79]. [Pg.124]

The purpose of validation is to demonstrate the capability of the water treatment and air handling system to continuously supply the required quantity of water and air with the specified quality attributes. Documented means to provide documented evidence. Validation provides the system owner with the means of assessing when a water treatment and/or air handling system is operating outside established control parameter limits and provides a means for bringing the system back into a state of control. It results in written operating and maintenance procedures for personnel to follow, which in turn helps ensure consistent system performance. [Pg.438]

The scope of the following chapter will be an attempt to identify system parameters limiting the efficiency of fluidized bed adsorption and to define operating parameters, e.g. adsorbent design, flow rate, column geometry, and... [Pg.201]

All possible combinations of the variables within the parameter limits... [Pg.179]

Introduction of the entropy correction term containing the Qjj parameter as an empirical parameter limits the usefulness of the theory of Flory and his co-workers. A consistent correction for the entropy and volume dependancies of this theory should start from a completely new form of the partition function. [Pg.128]

In order to understand this instability problem, the first step is to construct a linear stability analysis. This is used to define the parameter limits within which instabilities can be triggered by infinitesimal perturbations to the system. Within these parameter limits, a nonlinear stability analysis should be used to study the development of these instabilities. In this way, one can determine the parameter limits within which instabilities may be of practical concern. [Pg.39]

We would like to emphasize that parameter limits within which instabilities can be triggered by macroscopic perturbations to the system may be considerably broader. Within a certain range of parameters, a flow that may be stable to infinitesimal perturbations may be unstable to macroscopic perturbations. This distinction is important, since heterogeneities may represent macroscopic perturbations to an otherwise homogeneous system. [Pg.39]

Let us assume that the parameter limits within which an unstable... [Pg.45]

Unfortunately, most studies have not taken this approach. Numerical simulations of displacement have not been preceded by linear stability analyses to define the parameter limits within which an unstable displacement could be expected. [In their nonlinear stability analysis, Perrine and Gay (43) allowed their dispersion coefficients to be functions of velocity. In his linear stability analysis, Perrine (34, 35) assumed that his dispersion coefficients were constants.]... [Pg.48]

First, since most of these studies were not preceded by a linear stability analysis to define the parameter limits within which an unstable displacement could be expected, we are free to speculate that in some cases the displacements were actually stable to infinitesimally small perturbations (but not necessarily stable to the macroscopic perturbations). [Pg.49]

Standardized methods of testing (and methods validated by an official agency of validation), used strictly (without adaptation of test parameters), limited to specified tasks (type of products tested, range of measurement) not requiring individual validation ... [Pg.156]

In this model a canonical black hole is the one of spin parameter limited at the value 0.998, by the effect of the photons, which buffer the spin away from the extreme a = 1 Kerr value. [Pg.177]


See other pages where Parameter limits is mentioned: [Pg.263]    [Pg.230]    [Pg.271]    [Pg.274]    [Pg.275]    [Pg.111]    [Pg.154]    [Pg.193]    [Pg.200]    [Pg.231]    [Pg.233]    [Pg.140]    [Pg.297]    [Pg.298]    [Pg.91]    [Pg.579]    [Pg.179]    [Pg.335]    [Pg.459]    [Pg.91]    [Pg.48]    [Pg.246]    [Pg.846]    [Pg.140]    [Pg.45]   
See also in sourсe #XX -- [ Pg.177 ]




SEARCH



Approaches to Improvement of Gas Sensor Parameters and Limitations

Design parameters limitations

Dielectric-experimental parameters Frequency limits

Five-parameter model, limitation

Impedance-experimental parameters limits

System suitability test parameters limits determination

© 2024 chempedia.info