Paper/epoxy

Corrosion. Anticorrosion measures have become standard ia pipeline desiga, coastmctioa, and maintenance ia the oil and gas iadustries the principal measures are appHcation of corrosion-preventive coatings and cathodic protection for exterior protection and chemical additives for iaterior protectioa. Pipe for pipelines may be bought with a variety of coatiags, such as tar, fiber glass, felt and heavy paper, epoxy, polyethylene, etc, either pre-apphed or coated and wrapped on the job with special machines as the pipe is lowered iato the treach. An electric detector is used to determine if a coatiag gap (hoHday) exists bare spots are coated before the pipe is laid (see Corrosion and corrosion control). 

Materials for rigid laminates include paper-phenolic (the original material), paper-epoxy, and glass-epoxy. Composite laminates, which contain two or more types of reinforcing... 

Polyvinyl chloride, polyolefins, phenolic bonded paper, epoxy sealants. 

Property Paper, Phenolic Paper, Fire-retardant Phenolic Paper, Epoxy Glass Fabric, Epoxy Glass Fabric, Fire-retardant Epoxy Glass Fabric-paper, Epoxy Glass Fabric-glass mat. Epoxy... 

Therefore, special low-temperature studies of the flashover behavior of solid insulation materials at various helium states were conducted in connection with superconducting cable development at the Anstalt fur Tieftemperaturforschung (ATF) der Tech-nischen Universitat Graz (Institute for Low Temperature Research of the Technical University, Graz, Austria). The materials tested were polyethylene, teflon, polyamide (PAS-60), polypropylene, paper-polyester, paper-epoxy, plexiglass, and porcelain. 

Cellulose Paper Epoxy, Elame Resistant FR-3 N/A UL94V-1... 

Non-Woven Aramid Paper Epoxy/Multifunctional Epoxy... 

Aramid Paper Epoxy/Non-Epoxy, Phosphorus Flame Resistant... 

FR-3 Epoxy Paper Epoxy paper, cold punchable, high insulation resistance, flame-resistant... 

Hard, flexible metal Oil-alkyd modifier General purpose General purpose Water-soluble electrophoretic Styrene-co-maleic polyolefins anhydride grafted Specialty Glossy paper Epoxy resin hardener Allyl derivatives for polyesters... 

In this paper, epoxy composites were developed by using a synergistic combination of different type of conductive fillers. Both high in-plane and through-plane electrical conductivities were achieved. In addition, the plates showed good mechanical, chemical, and thermal properties. Acid and water refluxes were conducted to test the hygrothermal effects on the properties of the composites. 

Pentaerythritol in rosin ester form is used in hot-melt adhesive formulations, especially ethylene—vinyl acetate (EVA) copolymers, as a tackifier. Polyethers of pentaerythritol or trim ethyl ol eth an e are also used in EVA and polyurethane adhesives, which exhibit excellent bond strength and water resistance. The adhesives maybe available as EVA melts or dispersions (90,91) or as thixotropic, one-package, curable polyurethanes (92). Pentaerythritol spko ortho esters have been used in epoxy resin adhesives (93). The EVA adhesives are especially suitable for cellulose (paper, etc) bonding. 

A common surface cartridge is the pleated paper constmction type, which allows larger filtration areas to be packed iato a small space. Oil filters ia the automobile iadustry are of this type. The paper is impregnated, for strength, with epoxy or polyurethane resia. Any other medium ia sheet form, similar to cellulose paper, such as wool, polypropylene, or glass may be used. 

Aqueous dispersions are used in fiber bonding, paper coating, friction and abrasive appHcations, and laminates and wood bonding. PhenoHc dispersions improve the strength of latex-contact adhesive appHcations. Epoxy-modified phenoHc dispersions are prepared by dispersion of the phenoHc epoxy resin. The systems are used for baked primer appHcations and bonding requirements. Minimum baking conditions are 20 min at 150°C (25). 

This includes wire enamels on a base of polyvinyl formal, polyurethane or epoxy resins as well as moulding powder plastics on phenol-formaldehyde and similar binders, with cellulose fillers, laminated plastics on paper and cotton cloth base, triacetate cellulose films, films and fibres of polyethylene terephthalate. 

There are now commercially available a large range of laminated plastics materials. Resins used include the phenolics, the aminoplastics, polyesters, epoxies, silicones and the furane resins, whilst reinforcements may be of paper, cotton fibre, other organic fibres, asbestos, carbon fibre or glass fibre. Of these the phenolics were the first to achieve commercial significance and they are still of considerable importance. 

Nitrile rubber is compatible with phenol-formaldehyde resins, resorcinol-formaldehyde resins, vinyl chloride resins, alkyd resins, coumarone-indene resins, chlorinated rubber, epoxies and other resins, forming compositions which can be cured providing excellent adhesives of high strength, high oil resistance and high resilience. On the other hand, NBR adhesives are compatible with polar adherends such as fibres, textiles, paper and wood. Specific formulations of NBR adhesives can be found in [12]. 

Operating conditions are important determinants of the choice of filter media and sealant used in the cartridges. Some filter media, such as cellulose paper filters, are useful only at relatively low temperatures of 95 to 150"C (200 to 300°F). For high-temperature flue gas streams, more thermally stable filter media, such as nonwoven polyester, polypropylene, or Nomex, must be used. A variety of commercially available sealants such as polyurethane plastic and epoxy will allow fabric operating temperatures up tol50°C (300°F). Selected sealants such as heat cured Plasitcol will withstand operating temperatures up to 200°C (400°F). 

A reaction vessel explosion at BASF s resins plant in Cincinnati (July 19, 1990) killed one and injured 71. The BASF facility manufactures acrylic, alkyd, epoxy, and phenol-formaldehyde resins used as can and paper-cup liner coatings. The explosion occurred when a flammable solvent used to clean a reaction vessel vented into the plant and ignited. The cleaning solvent that was not properly vented to a condenser and separator, blew a pressure seal, and fdled the 80-year-old building with a white vapor cloud. 

Antimonious acid H3Sb03 and its salts are less well characterized but a few meta-antimonites and polyantimonites are known, e.g. NaSb02, NaSb305.H20 and Na2Sb407. The oxide itself finds extensive use as a flame retardant in fabrics, paper, paints, plastics, epoxy resins, adhesives and rubbers. The scale of industrial use can be gauged from the US statistics which indicate an annual consumption of Sb203 of some 10000 tonnes in that country. 

Shaw, J. D. N., Epoxy resins for construction recent developments, paper presented to the Japanese Society of Materials, November (1971). 

McCurrich, L. H. and Kay, W. M., Polyester and epoxy resin concrete, paper presented at the Symposium on Resins and Concrete, University of Newcastle-upon-Tyne, 17-18 April (1973). 

Figure 22. Practical 2000-A anode. Features include 108 channels and/or grooves, YBD carbon impregnated with epoxy, electrolytic nickel plate on carbon, electrolytic copper plate on nickel, copper wool packing, and central copper conductor. The anode is 20 cm in diameter and 120 cm long. (Reproduced with permission from paper 933 presented at the May 1997 meeting of The Electrochemical Society in Montreal.)...

Virtually all epoxy resins are made with starting materials based on epichlorohydrin, principally by reaction with bisphenol A. It is also used for the preparation of resins to increase the wet strength of paper. Both epichlorohydrin and glycidol are used in the manufacture of pharmaceuticals. 

---