Bonding fiber

Fiberboard boxes Fiber bonding resins Fiber boxes Fiber braiding Fiber can packaging Fiber diffraction... 

Locust bean gum and its derivatives are exceUent film formers and can be used either alone or in combination with starch as textile sizing agents and dye thickeners in textile printing, and as fiber bonding and beater additives in the papermaking industry. However, in most of these appHcations it has been replaced by guar. 

Early phenoHc resins consisted of self-curing, resole-type products made with excess formaldehyde, and novolaks, which are thermoplastic in nature and require a hardener. The early products produced by General BakeHte were used in molded parts, insulating varnishes, laminated sheets, and industrial coatings. These areas stiH remain important appHcations, but have been joined by numerous others such as wood bonding, fiber bonding, and plywood adhesives. The number of producers in the 1990s is approximately 20 in the United States and over 60 worldwide. 

Aqueous dispersions are used in fiber bonding, paper coating, friction and abrasive appHcations, and laminates and wood bonding. PhenoHc dispersions improve the strength of latex-contact adhesive appHcations. Epoxy-modified phenoHc dispersions are prepared by dispersion of the phenoHc epoxy resin. The systems are used for baked primer appHcations and bonding requirements. Minimum baking conditions are 20 min at 150°C (25). 

ARALL laminates, a family of hybrid composites consisting of aramid fibers bonded with epoxy between 0.3 mm thick aircraft ahoy sheets, were introduced in the 1980s (53). The laminates have lower density than even the new Al—Li ahoys and are greatly superior to monolithic aluminum sheet in resisting the growth of fatigue cracks. ARALL laminates have been specified for aircraft stmcture which is subjected to cycHc tension loads (see Laminates). 

Refining and Fractionation. These processes are used to alter and select cellulose properties so the final sheet has the desired properties (51). Properties of recycled fibers differ from those of fibers prepared directly from wood. For example, recovered chemical fibers have lower freeness, an apparent viscosity leading to different water drainage characteristics on paper machines. Recovered fibers also have iacreased apparent density, lower sheet strength, iacreased sheet opacity, inferior fiber—fiber bonding properties, lower fiber sweUiag, lower fiber flexibiUty, lower water reteatioa, reduced fiber fibrillatioa, and much lower internal fiber delamination. 

Nitrile latices are used ia a wide variety of appHcations, including production of dipped nitrile mbber products. In the principle use of paper saturation, adhesives and fiber bonding, small particle size and optimum surface tension is desirable to achieve rapid penetration and setup or dryiag. 

Low DS hydroxyethyl starches are used as paper coatings and sizes to improve sheet strength and stiffness. They are also employed as paper-coating color adhesives, and to increase fiber bonding in paper products. Hydroxyethylstarches are also used as textile warp sizes. 

Fig. 8. Electron micrograph of Merino wool fibers in a fabric that have been treated with a typical shrink-resistance polymer, showing fiber—fiber bond...

The process of textile print coloration can be divided into three steps. First, the colorant is appHed as pigment dispersion, dye dispersion, or dye solution from a vehicle caUed print paste or printing ink, containing in addition to the colorant such solutions or dispersions of chemicals as may be required by the colorant or textile substrate to improve and assist in dye solubUity, dispersion stabUity, pH, lubricity, hygroscopicity, rate of dye fixation to the substrate, and colorant-fiber bonding. The required viscosity characteristics of a print paste are achieved by addition of natural or synthetic thickening agents or by use of emulsions. 

The strength of a bond increases with the wood density in the region of approx. 0.7 to 0.8 g/cm Above this density, a decrease of the bond strength occurs. Performance and properties of wood-based panels are strongly influenced by the properties of the used wood. The anisotropy as well as the heterogeneity, the variability of various properties and the hygroscopicity have to be taken into account. Also the orientation of the wood fibers bonding solid wood has to be considered. 

Pressed Wood Products A group of materials used in building and furniture construction that are made from wood veneers, particles, or fibers bonded together with an adhesive under heat and pressure. 

In investigations of the failure of fiber compositions (PETP — short glass fibers) [251] it was found that the main process responsible for composite failure under load is the rupture at the matrix-fiber interface. The author of [251] observed formation of microvoids in loaded samples, both at the interphases and in the bulk. The microvoids, or cavities) grow in size and become interconnected by microcracks, and this results in fiber separation from the binder. However, when the matrix-fiber bond is strong enough, the cavities appear mostly in the bulk of matrix, the failure of the specimen does not over-power cohesion and traces of polymer remain on the fibers. 

DSC and DMA scans of, 18 778 Novolac epoxy resins, 10 349 Novolac resins, 15 163. See also Novolacs in coatings, 18 782 in fiber bonding, 18 792 from phenolic resin polymerization,... 

C. Ji, G. J. Fleming, M. Fleming, and M. Mathias. Acrylic fiber bonded carbon fiber paper as gas diffusion media for fuel cell. US Patent 2007/0218346 (2007). 

Nonwovens are textile products that are manufactured directly from fibers. They are defined as a manufactured sheet, web, or matt of directionally or randomly oriented fibers, bonded by friction, and/or cohesion, and/or adhesion excluding paper and products which are woven, tufted, stichbounded incorporating binding yams or filaments, or felted by wetmilling whether or not additionally needed. The fibers may be of natural or manmade origin. They may be staple or continuous filaments or maybe formed in situ. ... 

Fig. 3. Scanning electron photomicrographs of bonded PGA fiber meshes prepared by a fiber bonding method [30]. Note the formation of inter-fiber bonds at the fiber cross-points. (Reproduced with permission from [30])...

In order to overcome some of the drawbacks associated with the fiber bonding preparation, a solvent-casting and particulate-leaching technique was developed [32], With appropriate thermal treatment porous constructs of synthetic biode-... 

---