Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Oxidation resistance stainless steel

Modification of the metal itself, by alloying for corrosion resistance, or substitution of a more corrosion-resistant metal, is often worth the increased capital cost. Titanium has excellent corrosion resistance, even when not alloyed, because of its tough natural oxide film, but it is presently rather expensive for routine use (e.g., in chemical process equipment), unless the increased capital cost is a secondary consideration. Iron is almost twice as dense as titanium, which may influence the choice of metal on structural grounds, but it can be alloyed with 11% or more chromium for corrosion resistance (stainless steels, Section 16.8) or, for resistance to acid attack, with an element such as silicon or molybdenum that will give a film of an acidic oxide (SiC>2 and M0O3, the anhydrides of silicic and molybdic acids) on the metal surface. Silicon, however, tends to make steel brittle. Nevertheless, the proprietary alloys Duriron (14.5% Si, 0.95% C) and Durichlor (14.5% Si, 3% Mo) are very serviceable for chemical engineering operations involving acids. Molybdenum also confers special acid and chloride resistant properties on type 316 stainless steel. Metals that rely on oxide films for corrosion resistance should, of course, be used only in Eh conditions under which passivity can be maintained. [Pg.352]

Some materials are more susceptible to crevice corrosion than others. These materials depend on an oxide film to achieve corrosion resistance. Stainless steel and titanium are prime examples. In addition to improving the design to minimize crevices and to maintain a clean surface on certain materials, alloying of particular materials can be used to improve their resistance to corrosion. [Pg.517]

Corrosion-resistant stainless steels are generally able to withstand the acidic fuel cell conditions owing to their intrinsic property to from stable and well-adhering surface oxides, protecting the bulk material from further corrosive attack. On the other hand, with the growing chromium oxide layer, the contact resistance of... [Pg.269]

The high mechanical precision, a prerequisite for the optimum performance of this type of coupling aiming in perfect gas flow conditions, could up to now only be achieved by using corrosion resistant stainless steel. Thus the Skimmer coupling can be applied up to 800°C in inert and oxidizing atmosphere. The fact that the coupling... [Pg.75]

Alloying with both chromium and nickel increases scaling resistance. Stainless steels or nickel alloys, except alloy 400 (N04400), are required to provide satisfactory oxidation resistance at temperatures above 705 °C. Thermal cycling, applied stresses, moisture and sulfur-bearing gases will decrease scaling resistance. [Pg.17]

Calorimetric cell (glass [2] or corrosion-resistant stainless steel) shown in Figure 7.1a. It is dried at a temperature above 100 °C and flushed with a dry gas such as nitrogen or argon. The blanket of inert gas also avoids possible oxidation of some compounds. [Pg.403]

Bertrand et al. have studied the influence of hydrogen plasma excited by means of microwaves at 2.45 GHz to native oxide films on stainless steel and aluminum. Using in situ IR-ellipsometry, it could be shown that the native oxide on stainless steel was almost completely reduced in a hydrogen plasma. In contradiction to this, the aluminum surface was more resistant and only the outermost hydroxylated part of the oxide layer could be reduced. It was also observed that a dense oxide layer could be grown on the pretreated steel surface by subsequent oxygen plasma [222]. [Pg.652]

Standard Wrought Steels. Steels containing 11% and more of chromium are classed as stainless steels. The prime characteristics are corrosion and oxidation resistance, which increase as the chromium content is increased. Three groups of wrought stainless steels, series 200, 300, and 400, have composition limits that have been standardized by the American Iron and Steel Institute (AlSl) (see Steel). Figure 8 compares the creep—mpture strengths of the standard austenitic stainless steels that are most commonly used at elevated temperatures (35). Compositions of these steels are Hsted in Table 3. [Pg.117]

Ferritic stainless steels depend on chromium for high temperature corrosion resistance. A Cr202 scale may form on an alloy above 600°C when the chromium content is ca 13 wt % (36,37). This scale has excellent protective properties and occurs iu the form of a very thin layer containing up to 2 wt % iron. At chromium contents above 19 wt % the metal loss owiag to oxidation at 950°C is quite small. Such alloys also are quite resistant to attack by water vapor at 600°C (38). Isothermal oxidation resistance for some ferritic stainless steels has been reported after 10,000 h at 815°C (39). Grades 410 and 430, with 11.5—13.5 wt % Cr and 14—18 wt % Cr, respectively, behaved significandy better than type 409 which has a chromium content of 11 wt %. [Pg.118]

The fifth component is the stmcture, a material selected for weak absorption for neutrons, and having adequate strength and resistance to corrosion. In thermal reactors, uranium oxide pellets are held and supported by metal tubes, called the cladding. The cladding is composed of zirconium, in the form of an alloy called Zircaloy. Some early reactors used aluminum fast reactors use stainless steel. Additional hardware is required to hold the bundles of fuel rods within a fuel assembly and to support the assembhes that are inserted and removed from the reactor core. Stainless steel is commonly used for such hardware. If the reactor is operated at high temperature and pressure, a thick-walled steel reactor vessel is needed. [Pg.210]

The metallurgy of the cyclone equipment has in recent years focused primarily on type 304 H stainless steel. The 304 H material is durable and easy to fabricate and repair, withstands the high regenerator temperatures, and is oxidation- and corrosion-resistant. Essentially all internal surfaces of the cyclone that are subject to erosion are protected with a 2 cm layer of erosion-resistant lining. When installed and cured, most refractory linings are highly resistant to erosion. [Pg.218]

Storage. Carbon steel and stainless steel should be used for all equipment in ethylene oxide service. Ethylene oxide attacks most organic materials (including plastics, coatings, and elastomers) however, certain fluoroplastics ate resistant and can be used in gaskets and O-rings. See Reference 9 for a hst of materials that are compatible with ethylene oxide. [Pg.462]

Rigid Porous Media These are available in sheets or plates and tubes. Materials used include sintered stainless steel and other metals, graphite, aluminum oxide, silica, porcelain, and some plastics—a gamut that allows a wide range of chemical and temperature resistance. Most applications are for clarification. [Pg.1707]

Substituting one alloy for another may be the only viable solution to a specific corrosion problem. However, caution should be exercised this is especially true in a cooling water environment containing deposits. Concentration cell corrosion is insidious. Corrosion-resistant materials in oxidizing environments such as stainless steels can be severely pitted when surfaces are shielded by deposits. Each deposit is unique, and nature can be perverse. Thus, replacement materials ideally should be tested in the specific service environment before substitution is accepted. [Pg.85]

Stainless steels contain 11% or more chromium. Table 5.1 lists common commercial grades and compositions of stainless steels. It is chromium that imparts the stainless character to steel. Oxygen combines with chromium and iron to form a highly adherent and protective oxide film. If the film is ruptured in certain oxidizing environments, it rapidly heals with no substantial corrosion. This film does not readily form until at least 11% chromium is dissolved in the alloy. Below 11% chromium, corrosion resistance to oxygenated water is almost the same as in unalloyed iron. [Pg.103]

Corrosion resistance of stainless steel is reduced in deaerated solutions. This behavior is opposite to the behavior of iron, low-alloy steel, and most nonferrous metals in oxygenated waters. Stainless steels exhibit very low corrosion rates in oxidizing media until the solution oxidizing power becomes great enough to breach the protective oxide locally. The solution pH alone does not control attack (see Chap. 4, Underdeposit Corrosion ). The presence of chloride and other strong depassivating chemicals deteriorates corrosion resistance. [Pg.103]

Alloys whose corrosion resistance depends on forming a protective oxide layer, such as stainless steel, are susceptible to severe localized attack when pH falls as a result of nonoxidizing acid excursions. How-... [Pg.162]

Fig. 1.3. The fire grate, which carries the white-hot fire inside the firebox, must resist oxidation and creep. Stainless steel is best for this application. Note also the threaded monel stays which hold the firebox sides together against the internal pressure of the steam. Fig. 1.3. The fire grate, which carries the white-hot fire inside the firebox, must resist oxidation and creep. Stainless steel is best for this application. Note also the threaded monel stays which hold the firebox sides together against the internal pressure of the steam.
Furnace tubes, piping, and exchanger tubing with metal temperatures above 800°F now tend to be an austenitic stainless steel, e.g., Type 304, 321, and 347, although the chromium-molybdenum steels are still used extensively. The stainless steels are favored beeause not only are their creep and stress-rupture properties superior at temperatures over 900°F, but more importantly because of their vastly superior resistance to high-temperature sulfide corrosion and oxidation. Where corrosion is not a significant factor, e.g., steam generation, the low alloys, and in some applications, carbon steel may be used. [Pg.261]


See other pages where Oxidation resistance stainless steel is mentioned: [Pg.298]    [Pg.40]    [Pg.117]    [Pg.1747]    [Pg.352]    [Pg.327]    [Pg.334]    [Pg.355]    [Pg.698]    [Pg.392]    [Pg.119]    [Pg.119]    [Pg.123]    [Pg.131]    [Pg.129]    [Pg.26]    [Pg.501]    [Pg.370]    [Pg.399]    [Pg.48]    [Pg.120]    [Pg.126]    [Pg.126]    [Pg.486]    [Pg.138]    [Pg.484]    [Pg.2417]    [Pg.2464]    [Pg.509]    [Pg.30]    [Pg.299]    [Pg.931]   
See also in sourсe #XX -- [ Pg.426 ]




SEARCH



Oxidation resistance

Oxidation stainless steel

Stainless steel resistance

Stainless steels resistant

© 2024 chempedia.info