Opaqueness

In the dense interstellar medium characteristic of sites of star fonuation, for example, scattering of visible/UV light by sub-micron-sized dust grains makes molecular clouds optically opaque and lowers their internal temperature to only a few tens of Kelvin. The thenual radiation from such objects therefore peaks in the FIR and only becomes optically thin at even longer wavelengths. Rotational motions of small molecules and rovibrational transitions of larger species and clusters thus provide, in many cases, the only or the most powerfiil probes of the dense, cold gas and dust of the interstellar medium. 

This occurs naturally as a white solid in various crystalline forms, in all of which six oxygen atoms surround each titanium atom. Titanium dioxide is important as a white pigment, because it is nontoxic. chemically inert and highly opaque, and can be finely ground for paint purposes it is often prepared pure by dissolving the natural form in sulphuric acid, hydrolysing to the hydrated dioxide and heating the latter to make the anhydrous form. 

Alternatively, treat a solution of 3 9 g. of the 6is-diazo ketone in 50 ml. of warm dioxan with 15 ml. of 20 per cent, aqueous ammonia and 3 ml. of 10 per cent, aqueous silver nitrate under reflux in a 250 or 500 ml. flask on a water bath. Nitrogen is gently evolved for a few minutes, followed by a violent reaction and the production of a dark brown and opaque mixture. Continue the heating for 30 minutes on the water bath and filter hot the diamide of decane-1 lO dicarboxyhc acid is deposited on cooling. Filter this off and dry the yield is 3 -1 g., m.p. 182-184°, raised to 184-185° after recrystallisation from 25 per cent, aqueous acetic add. Hydrolyse the diamide (1 mol) by refluxing for 2-5 hours with 3N potassium hydroxide (4 mols) acidify and recrystaUise the acid from 20 per cent, acetic acid. The yield of decane-1 10-dicarboxyhc acid, m.p. 127-128°, is almost quantitative. 

In a wide-mouthed test-tube ( boiling tube ) place 5 g. of phenol, 15 ml. of 40 per cent, formaldehyde solution and 3 ml. of concentrated ammonia solution (sp. gr. 0-88). Warm the mixtme with a small flame until it becomes opaque. Cool, discard the aqueous layer, but retain the viscous material in the tube. Heat the latter in a water bath at 60° for 30 minutes and then heat the pasty mass in an air oven at 75° for 4-6 hours. A hard sohd resin is produced. 

Buckets, tubs, funnels, and all sorts of containers of this whitish, opaque, pliable plastic can be [Figure 2]... 

If the crystals are opaque white and do not deliquesce quickly in air of average humidity (65% rh), they may be contaminated with some Hex amine. Washing 100g of the crude product with lOOmL of Chloroform by stirring in a beaker then filtering, repeated as many times as necessary, will remove Hex amine. Methylamine HCI is insoluble in Chloroform whereas Hexamine Is at the rate of 1g to 10mL. 

Transparent solid samples can be analyzed directly by placing them in the IR beam. Most solid samples, however, are opaque and must be dispersed in a more transparent medium before recording a traditional transmission spectrum. If a suitable solvent is available, then the solid can be analyzed by preparing a solution and analyzing as described earlier. When a suitable solvent is not available, solid samples may be analyzed by preparing a mull of the finely powdered sample with a suitable oil. Alternatively, the powdered sample can be mixed with KBr and pressed into an optically transparent pellet. 

Like e, t is the product of two contributions the concentration N/V of the centers responsible for the effect and the contribution per particle to the attenuation. It may help us to become oriented with the latter to think of the scattering centers as opaque spheres of radius R. These project opaque cross sections of area ttR in the light path. The actual cross section is then multiplied by the scattering efficiency factor optical cross... 

As for the far-infrared, absorption by air in the vacuum-ultraviolet (VUV) necessitates evacuation of the optical path from source to detector. In this region it is oxygen which absorbs, being opaque below 185 nm. 

The attenuated total reflectance (ATR) technique is used commonly in the near-infrared for obtaining absorption spectra of thin Aims and opaque materials. The sample, of refractive index i, is placed in direct contact with a material which is transparent in the region of interest, such as thallium bromide/thallium iodide (known as KRS-5), silver chloride or germanium, of relatively high refractive index so that Then, as Figure 3.f8... 

Whereas ATR spectroscopy is most commonly applied in obtaining infrared absorption spectra of opaque materials, reflection-absorption infrared spectroscopy (RAIRS) is usually used to obtain the absorption spectrum of a thin layer of material adsorbed on an opaque metal surface. An example would be carbon monoxide adsorbed on copper. The metal surface may be either in the form of a film or, of greaf imporfance in fhe sfudy of cafalysfs, one of fhe parficular crysfal faces of fhe mefal. 

Fig. 1. The hthographic process. A substrate is coated with a photosensitive polymer film called a resist. A mask with transparent and opaque areas directs radiation to preselected regions of the resist film. Depending on resist characteristics, exposed or unexposed portions of the film are removed using a developer solvent. The resulting pattern is then transferred to the substrate surface and the resist is stripped.

In general, textile fibers should be optically opaque so that their refractive indexes need to be significantly different from those of their most common environments, namely, air and water. Luster and color are two optical properties that relate to a fiber s aesthetic quatity and consumer acceptance. 

---