Microfiltration examples

Whereas many of these technologies are not really new, they have never had the regulatory and economic justification for their use in metallizing. Each of these general methods has many variants. Some may be directed to waste treatment, some to recycle, and some to reclaim. An example is filtration, used to prevent release to air of zinc particles from flame spraying, microfiltration of cleaners to extend hfe, in combination with chemical precipitation to remove metal particles from wastewater, and many other uses. 

The individual membrane filtration processes are defined chiefly by pore size although there is some overlap. The smallest membrane pore size is used in reverse osmosis (0.0005—0.002 microns), followed by nanofiltration (0.001—0.01 microns), ultrafHtration (0.002—0.1 microns), and microfiltration (0.1—1.0 microns). Electro dialysis uses electric current to transport ionic species across a membrane. Micro- and ultrafHtration rely on pore size for material separation, reverse osmosis on pore size and diffusion, and electro dialysis on diffusion. Separation efficiency does not reach 100% for any of these membrane processes. For example, when used to desalinate—soften water for industrial processes, the concentrated salt stream (reject) from reverse osmosis can be 20% of the total flow. These concentrated, yet stiH dilute streams, may require additional treatment or special disposal methods. 

Ultrafiltration may be distinguished from other membrane operations by example When reverse osmosis is used to process whey, it passes only the water and some of the lactic acid (due to the solubihty of lactic acid in RO membranes). Nanofiltration used on whey will pass most of the sodium salts while retaining the calcium salts and most of the lactose. Microfiltration will pass everything except the particulates and the bacteria. 

Brief Examples Microfiltration is the oldest and largest membrane field. It was important economically when other disciphnes were struggling for acceptance, yet because of its incredible diversity and lack of large apphcations, it is the most difficult to categorize. Nonetheless, it has had greater membrane sales than all other membrane applications combined throughout most of its histoiy. The early... 

To apply these data and equations to the problem of ground resistance, the maximum anticipated current must first be estimated. For practical industrial situations, Iq varies in the range 0.01-100/rA. The upper value represents extreme cases such as microfiltration and the lower value to slow flow in pipe. Typical charging currents for tank tmck loading are of the order 1 /rA (5-3.1.1). As an example, consider a system such as a tank with a capacitance less than 1000 pF. First, consider the minimum ignition voltages in Table A-4-1.3b. From Eq. (2), f L = In the case of hydrogen the mini-... 

Laboratory Microfiltration membranes have countless laboratory uses, such as recovering biomass, measuring particulates in water, clarifying and sterilizing protein solutions, and so on. There are countless examples for both general chemistry and biology, especially for analytical proc ures. Most of these apphcations are run in dead-end flow, with the membrane replacing a more conventional medium such as filter paper. 

Downstream Processing Microfiltration plays a significant role in downstream processing of fermentation products in the pharmaceutical and bioprocessing industry. Examples are clarification of fermentation broths, sterile filtration, cell recycle in continuous fermentation, harvesting mammahan cells, cell washing, mycelia recovery, lysate recovery, enzyme purification, vaccines, and so forth. 

Stretched Polymers MF membranes may be made by stretching (Fig. 20-68). Semicrystalline polymers, if stretched perpendicular to the axis of crystallite orientation, may fracture in such a way as to make reproducible microchannels. Best known are Goretex produced from Teflon , and Celgard produced from polyolefin. Stretched polymers have unusually large fractions of open space, giving them very high fluxes in the microfiltration of gases, for example. Most such materials are very hydrophobic. 

When planning an industrial-scale bioprocess, the main requirement is to scale up each of the process steps. As the principles of the unit operations used in these downstream processes have been outlined in previous chapters, at this point we discuss only examples of practical applications and scaling-up methods of two unit operations that are frequently used in downstream processes (i) cell separation by filtration and microfiltration and (ii) chromatography for fine purification of the target products. 

Particles smaller than the largest pores, but larger than the smallest pores are partially rejected, according to the pore size distribution of the membrane. Particles much smaller than the smallest pores will pass through the membrane. Thus, separation of solutes by microporous membranes is mainly a function of molecular size and pore size distribution. In general, only molecules that differ considerably in size can be separated effectively by microporous membranes, for example, in ultrafiltration and microfiltration. 

The bubble point test is simple, quick and reliable and is by far the most widely used method of characterizing microfiltration membranes. The membrane is first wetted with a suitable liquid, usually water for hydrophilic membranes and methanol for hydrophobic membranes. The membrane is then placed in a holder with a layer of liquid on the top surface. Air is fed to the bottom of the membrane, and the pressure is slowly increased until the first continuous string of air bubbles at the membrane surface is observed. This pressure is called the bubble point pressure and is a characteristic measure of the diameter of the largest pore in the membrane. Obtaining reliable and consistent results with the bubble point test requires care. It is essential, for example, that the membrane be completely wetted with the test liquid this may be difficult to determine. Because this test is so widely used by microfiltration membrane manufacturers, a great deal of work has been devoted to developing a reliable test procedure to address this and other issues. The use of this test is reviewed in Meltzer s book [3],... 

The advantages and disadvantages of in-line microfiltration and cross-flow filtration are compared in Table 7.2. In general, in-line filtration is preferred as a polishing operation for already clean solutions, for example, to sterilize water... 

Cross-section structure. An anisotropic membrane (also called asymmetric ) has a thin porous or nonporous selective barrier, supported mechanically by a much thicker porous substructure. This type of morphology reduces the effective thickness of the selective barrier, and the permeate flux can be enhanced without changes in selectivity. Isotropic ( symmetric ) membrane cross-sections can be found for self-supported nonporous membranes (mainly ion-exchange) and macroporous microfiltration (MF) membranes (also often used in membrane contactors [1]). The only example for an established isotropic porous membrane for molecular separations is the case of track-etched polymer films with pore diameters down to about 10 run. All the above-mentioned membranes can in principle be made from one material. In contrast to such an integrally anisotropic membrane (homogeneous with respect to composition), a thin-film composite (TFC) membrane consists of different materials for the thin selective barrier layer and the support structure. In composite membranes in general, a combination of two (or more) materials with different characteristics is used with the aim to achieve synergetic properties. Other examples besides thin-film are pore-filled or pore surface-coated composite membranes or mixed-matrix membranes [3]. 

Metal oxides, used for manufacturing of ceramic nanofiltration membranes, are intrinsically hydrophilic. This limits the use of these membranes to polar solvents filtration of nonpolar solvents (n-hexane, toluene, cyclohexane) usually yields zero fluxes. Attempts have been made to modify the pore structure by adding hydrophobic groups, for example, in a silane coupling reaction [38, 43]. This approach is similar to modifications of ultrafiltration and microfiltration membranes... 

Catalytic reactions can be combined in membrane-assisted integrated catalytic processes with practically all the membrane unit operations available today. Many examples of integration of membrane contactors, pervaporation, gas separation, nanofiltration, microfiltration, and ultrafiltration operations together with catalytic reactions, have been proposed in the literature. 

MWCO), usually defined as the molar mass at which the membrane rejects 90% of solute molecules. However, as in microfiltration, the molecular shape can affect permeability through the membrane pores. For example, a membrane with a nominal cut-off of 100 kDa, which does not allow globular molecules with a molar mass of 100 kDa to flow through, may allow fibrous molecules with higher molar masses to flow across the pores. As in microfiltration, the membrane pore size is not uniform, with a normal distribution around an average value. 

In micro- and ultrafiltrations, the mode of separation is by sieving through line pores, where microfiltration membranes filter colloidal particles and bacteria from 0.1 to 10 mm, and ultrafiltration membranes filter dissolved macromolecules. Usually, a polymer membrane, for example, cellulose nitrate, polyacrilonytrile, polysulfone, polycarbonate, polyethylene, polypropylene, poly-tretrafhioroethylene, polyamide, and polyvinylchloride, permits the passage of specific constituents of a feed stream as a permeate flow through its pores, while other, usually larger components of the feed stream are rejected by the membrane from the permeate flow and incorporated in the retentate flow [10,148,149],... 

The work described in this chapter is especially concerned with three of the most widely used pressure driven membrane processes microfiltration, ultrafiltration and nanofiltration. These are usually classified in terms of the size of materials which they separate, with ranges typically given as 10.0-0.1 xm for microfiltration, 0.1 p.m-5 nm for ultrafiltration, and 1 nm for nanofiltration. The membranes used have pore sizes in these ranges. Such pores are best visualised by means of atomic force microscopy (AFM) [3]. Figure 14.1 shows an example of a single pore in each of these three types of membrane. An industrial membrane process may use several hundred square meters of membrane area containing billions of such pores. 

---