Micellar products

Synthesis of oil soluble micellar calcium thiophosphate was performed in a one-step process involving the reaction of calcium oxide, tetraphosphorus decasulfide and water in the presence of an alkylaryl sulfonic acid. This product could be defined as a calcium thiophosphate hard-core surrounded by a calcium alkylarylsulphonate shell in accordance with a reverse micelle type association in oil. Three micellar products with the same chemical nature core were prepared, each with different core/shell ratio of 0.44, 0.92 and 1.54. Better performances are expected with products of higher core/shell ratios. The antiwear performance of micellar calcium carbonates is directly linked to the size of the mineral CaC03 colloidal particles. At a concentration of 2 % micellar cores, no antiwear effect is observed whatever the micellar size. At an intermediate concentration of 4 % of micellar cores, the wear scar diameter is clearly dependent on the micellar size, slipping from 1.70 mm to 1.10 mm, then to 0.79 mm when the core diameter moves from 4.37 nm to 6.07 nm, then to 6.78 nm. Size dependence is increased at a concentration of 5 % in colloidal cores. This clearly confirms the size dependence of the micellar cores on their antiwear performance (Delfort et al.,... 

Utilizing FT-EPR teclmiques, van Willigen and co-workers have studied the photoinduced electron transfer from zinc tetrakis(4-sulfonatophenyl)porphyrin (ZnTPPS) to duroquinone (DQ) to fonn ZnTPPS and DQ in different micellar solutions [34, 63]. Spin-correlated radical pairs [ZnTPPS. . . DQ ] are fomied initially, and the SCRP lifetime depends upon the solution enviromnent. The ZnTPPS is not observed due to its short T2 relaxation time, but the spectra of DQ allow for the detemiination of the location and stability of reactant and product species in the various micellar solutions. While DQ is always located within the micelle, tire... 

A particularly interesting type of micellar catalysis is the autocatalytic self-replication of micelles [58]. Various examples have been described, but a particularly interesting case is the biphasic self-reproduction of aqueous caprylate micelles [59]. In this system ethyl caprylate undergoes hydroxyl catalysed hydrolysis to produce the free carboxylate anion, caprylate. Caprylate micelles then fonn. As these micelles fonn, they solubilize ethylcaprylate and catalyse further production of caprylate anion and caprylate micelles. 

By 1980, research and development shifted from relatively inexpensive surfactants such as petroleum sulfonates to more cosdy but more effective surfactants tailored to reservoir and cmde oil properties. Critical surfactant issues are performance in saline injection waters, adsorption on reservoir rock, partitioning into reservoir cmde oil, chemical stabiUty in the reservoir, interactions with the mobiUty control polymer, and production problems caused by resultant emulsions. Reservoir heterogeneity can also greatly reduce process effectiveness. The decline in oil prices in the early 1980s halted much of the work because of the relatively high cost of micellar processes. 

An alternative to this process is low (<10 N/m (10 dynes /cm)) tension polymer flooding where lower concentrations of surfactant are used compared to micellar polymer flooding. Chemical adsorption is reduced compared to micellar polymer flooding. Increases in oil production compared to waterflooding have been observed in laboratory tests. The physical chemistry of this process has been reviewed (247). Among the surfactants used in this process are alcohol propoxyethoxy sulfonates, the stmcture of which can be adjusted to the salinity of the injection water (248). 

The NOBS system undergoes an additional reaction that forms a diacyl peroxide as a result of the nucleophilic attack of the peracid anion on the NOBS precursor as shown in equation 21. This undesirable side reaction can be minimized by the use of an excess molar quantity of hydrogen peroxide (91,96) or by the use of shorter dialkyl chain acid derivatives. However, the use of these acid derivatives also appears to result in less efficient bleaching. The dependence of the acid group on the side product formation is apparentiy the result of the proximity of the newly formed peracid to unreacted NOBS in the micellar environment (91). A variety of other peracid precursor stmctures can be found (97—118). 

Product recoveiy from reversed micellar solutions can often be attained by simple back extrac tion, by contacting with an aqueous solution having salt concentration and pH that disfavors protein solu-bihzation, but this is not always a reliable method. Addition of cosolvents such as ethyl acetate or alcohols can lead to a disruption of the micelles and expulsion of the protein species, but this may also lead to protein denaturation. These additives must be removed by distillation, for example, to enable reconstitution of the micellar phase. Temperature increases can similarly lead to product release as a concentrated aqueous solution. Removal of the water from the reversed micelles by molecular sieves or sihca gel has also been found to cause a precipitation of the protein from the organic phase. 

Apparent exceptions are the constants k2 for diazonium salts with the electron-withdrawing substituents 4-C1 and 3-CN. The values of k2 for these compounds are more than a factor of 10 larger than expected on the basis of Hammett relationships. Product analyses rationalize this observation whereas in all other cases products are likely to be formed by heterolytic dediazoniation, the products from the 4-chloro-and 3-cyanobenzenediazonium ions include chlorobenzene and benzonitrile, typical compounds obtained in homolytic dediazoniations. This result corresponds to the reaction products observed by Moss et al. (1982) in micellar dediazoniation, compared with the nonmicellar reaction (see Sec. 8.3). 

The development of monoalkyl phosphate as a low skin irritating anionic surfactant is accented in a review with 30 references on monoalkyl phosphate salts, including surface-active properties, cutaneous effects, and applications to paste and liquid-type skin cleansers, and also phosphorylation reactions from the viewpoint of industrial production [26]. Amine salts of acrylate ester polymers, which are physiologically acceptable and useful as surfactants, are prepared by transesterification of alkyl acrylate polymers with 4-morpholinethanol or the alkanolamines and fatty alcohols or alkoxylated alkylphenols, and neutralizing with carboxylic or phosphoric acid. The polymer salt was used as an emulsifying agent for oils and waxes [70]. Preparation of pharmaceutical liposomes with surfactants derived from phosphoric acid is described in [279]. Lipid bilayer vesicles comprise an anionic or zwitterionic surfactant which when dispersed in H20 at a temperature above the phase transition temperature is in a micellar phase and a second lipid which is a single-chain fatty acid, fatty acid ester, or fatty alcohol which is in an emulsion phase, and cholesterol or a derivative. 

The micellar effect on the endo/exo diastereoselectivity of the reaction has also been investigated. The endo/exo ratio of the reaction of cyclopentadiene with methyl acrylate is affected little (compared to water) by the use of SDS and CTAB [73b], while a large enhancement was observed in SDS solution when n-butyl acrylate was the dienophile used [74]. The ratio of endo/exo products in the reaction of 1 with 113c is not affected by CTAB, SDS and C12E7 [72a]. 

Micellar nanocarriers have already been applied successfully for delivery of hydro-phobic drugs [86]. These carriers are usually the product of self-assembled block copolymers, consisting of a hydrophilic block and a hydrophobic block. Generally, an ELP with a transition temperature below body temperature is used as hydrophobic block and the hydrophilic block can be an ELP with a transition temperature above body temperature or another peptide or protein. The EPR effect also directs these types of carriers towards tumor tissue. 

Subsequently, cationic rhodium catalysts are also found to be effective for the regio- and stereoselective hydrosilation of alkynes in aqueous media. Recently, Oshima et al. reported a rhodium-catalyzed hydrosilylation of alkynes in an aqueous micellar system. A combination of [RhCl(nbd)]2 and bis-(diphenylphosphi no)propanc (dppp) were shown to be effective for the ( >selective hydrosilation in the presence of sodium dodecylsulfate (SDS), an anionic surfactant, in water.86 An anionic surfactant is essential for this ( )-selective hydrosilation, possibly because anionic micelles are helpful for the formation of a cationic rhodium species via dissociation of the Rh-Cl bond. For example, Triton X-100, a neutral surfactant, gave nonstereoselective hydrosilation whereas methyltrioctylammonium chloride, a cationic surfactant, resulted in none of the hydrosilation products. It was also found that the selectivity can be switched from E to Z in the presence of sodium iodide (Eq. 4.47). 

Much effort has been directed at developing aqueous Diels-Alder reactions toward the syntheses of a variety of complex natural products. Grieco employed micellar catalysis and pure water as the solvent for the Diels-Alder reaction of dienecarboxylate with a variety of dienophiles. For example, when the Diels-Alder reaction in Scheme 12.3 was carried out in water, a higher reaction rate and reversal of the selectivity were observed, compared with the same reaction in a hydrocarbon solvent (Scheme 12.3).81 Similarly, the reaction of 2,6-dimethylbenzoquinone with sodium ( )-3,5-hexadienoate (generated in situ by the addition of 0.95 equiv sodium bicarbonate to a suspension of the precursor acid in water) proceeded for 1 hour to give a 77% yield of the adduct... 

Recent research and field tests have focused on the use of relatively low concentrations or volumes of chemicals as additives to other oil recovery processes. Of particular interest is the use of surfactants as CO (184) and steam mobility control agents (foam). Also combinations of older EOR processes such as surfactant enhanced alkaline flooding and alkaline-surfactant-polymer flooding have been the subjects of recent interest. Older technologies polymer flooding (185,186) and micellar flooding (187-189) have been the subject of recent reviews. In 1988 84 commercial products polymers, surfactants, and other additives, were listed as being marketed by 19 companies for various enhanced oil recovery applications (190). 

Limit Concentration of Monomers in Solution In the calcic environment considered, the CMC values of surfactants are low. For example, sulfonate and Genapol solutions reach their CMC at 30 ppm (Table II). The surfactant solutions injected in practice at concentration of about one or several percent are thus generally used well above their CMC. Under such conditions, the predominant fraction of each surfactant is the micellar form whose composition (xj) is practically equal to the initial proportion of products (i.e. alpha 1 for sulfonate). At this concentration level of products, very small proportions of monomer species coexist, the limit concentrations of which are respectively ... 

In both cases, overall adsorption and especially that of sulfonate (or "primary surfactant in the composition of most micellar systems used for EOR) are considerably reduced by simply adding a second product having low adsorption characteristics (NP 30 EO in the above example). This is why we have called this strongly hydrophilic surfactant a desorbent. 

Figures 5 and 6 show that the concentration of the two surfactants in the effluents increases simultaneously with the production of the desorbent, which confirms the mixed micellization mechanism described above. Figure 5, where the three additives are produced lately, illustrates the phenomenon particularly well. At the lower pH corresponding to strong adsorption conditions for sulfonate (test 4), the one pore-volume micellar slug would have been entirely consumed by the medium in the absence of any desorbent.

Surfactant Transport in an Adsorbent Porous Medium. Chromatographic Aspects A first observation was made in all the tests in Table III. The breakthrough of both surfactants from the micellar slug always occurs simultaneously without any chromatographic effect (Figures 5 and 6). This stems both from the chemical nature of the two products selected and also from the fact that the injected concentration is much greater than the CMC of their mixtures. 

Figure 9. Production History of 5% PV Micellar Slug B4 and 50% PV Buffer Injected at 1.41 m/day...

Deriving an expression for f(t) a considerable simplification occurs if one takes all polymer particles to be nucleated at the same size dp(t,t). The generation of new polymer particles in an emulsion system is basically due to two mechanisms micellar and homogeneous particle production. Then, the rate of particle nucleation, fit), can be expressed as (12) ... 

---