Methyl methacrylate, synthesis

Attaching a pyridine group on the phosphine (e.g. PPh2Py) is also believed to enhance the catalytic activity in methyl methacrylate synthesis by picking up protons in solution and transferring them to the metal centre, which then uses them in the reaction [26], Such a process has been termed a proton messenger. 

Journal of Polymer Science Polymer Chatnstry Edition 42, No.20,15thOct.2004, p.5227-34 ANTIMICROBIAL ACTIVITY ON THE COPOLYMERS OF 2,4-DICHLOROPHENYL METHACRYLATE WITH METHYL METHACRYLATE SYNTHESIS AND CHARACTERIZATION Patel M V Patel S A Ray A Patel R M Gujarat,Sardar Patel University... 

Commercial petrochemical processes using syngas or carbon monoxide are based on four principal classes of reactions phosgenation, Reppe chemistry, hydroformylations, and Koch carbonylations. Phosgenation is a key step in the manufacture of polyurethanes, polycarbonates, and monoisocyanates. Reppe chemistry is the basis for acetic acid and acetic anhydride production as well as formic acid and methyl methacrylate synthesis. Hydroformylations utilize syngas in the oxo synthesis to make a wide variety of aldehydes and long-chain alcohols. The fourth class of reactions are Koch carbonylations. Koch carbonylations are used commercially to produce neo acids which are specialty products that serve markets similar to 0X0 alcohols. 

ShuMa A., Srivastava A.K., Terpolymerization of linalool, styrene, and methyl methacrylate Synthesis, characterization, and a Mnetic study, Polyrru-Plast. Technol. Eng., 41(4), 2002,777-793. 

Pandey R, Kamal M., Srivastava A.K., Interpenetrating polymer network of poly(styrene) rmd poly(citronellol-alt-methyl methacrylate). Synthesis and characterization, Polym. J., 35(2), 2003,122-126. 

In 1954 the surface fluorination of polyethylene sheets by using a soHd CO2 cooled heat sink was patented (44). Later patents covered the fluorination of PVC (45) and polyethylene bottles (46). Studies of surface fluorination of polymer films have been reported (47). The fluorination of polyethylene powder was described (48) as a fiery intense reaction, which was finally controlled by dilution with an inert gas at reduced pressures. Direct fluorination of polymers was achieved in 1970 (8,49). More recently, surface fluorinations of poly(vinyl fluoride), polycarbonates, polystyrene, and poly(methyl methacrylate), and the surface fluorination of containers have been described (50,51). Partially fluorinated poly(ethylene terephthalate) and polyamides such as nylon have excellent soil release properties as well as high wettabiUty (52,53). The most advanced direct fluorination technology in the area of single-compound synthesis and synthesis of high performance fluids is currently practiced by 3M Co. of St. Paul, Minnesota, and by Exfluor Research Corp. of Austin, Texas. 

Until 1982, almost all methyl methacrylate produced woddwide was derived from the acetone cyanohydrin (C-3) process. In 1982, Nippon Shokubai Kagaku Kogyo Company introduced an isobutylene-based (C-4) process, which was quickly followed by Mitsubishi Rayon Company in 1983 (66). Japan Methacryhc Monomer Company, a joint venture of Nippon Shokubai and Sumitomo Chemical Company, introduced a C-4-based plant in 1984 (67). Isobutylene processes are less economically attractive in the United States where isobutylene finds use in the synthesis of methyl /i / butyl ether, a pollution-reducing gasoline additive. BASF began operation of an ethylene-based (C-2) plant in Ludwigshafen, Germany, in 1990, but favorable economics appear to be limited to conditions unique to that site. 

The performance of many metal-ion catalysts can be enhanced by doping with cesium compounds. This is a result both of the low ionization potential of cesium and its abiUty to stabilize high oxidation states of transition-metal oxo anions (50). Catalyst doping is one of the principal commercial uses of cesium. Cesium is a more powerflil oxidant than potassium, which it can replace. The amount of replacement is often a matter of economic benefit. Cesium-doped catalysts are used for the production of styrene monomer from ethyl benzene at metal oxide contacts or from toluene and methanol as Cs-exchanged zeofltes ethylene oxide ammonoxidation, acrolein (methacrolein) acryflc acid (methacrylic acid) methyl methacrylate monomer methanol phthahc anhydride anthraquinone various olefins chlorinations in low pressure ammonia synthesis and in the conversion of SO2 to SO in sulfuric acid production. 

Group-Transfer Polymerization. Living polymerization of acrylic monomers has been carried out using ketene silyl acetals as initiators. This chemistry can be used to make random, block, or graft copolymers of polar monomers. The following scheme demonstrates the synthesis of a methyl methacrylate—lauryl methacrylate (MMA—LMA) AB block copolymer (38). LMA is CH2=C(CH2)COO(CH2) CH2. 

Acrylic Esters. A procedure has been described for preparation of higher esters from methyl acrylate that illustrates the use of an acid catalyst together with the removal of one of the products by azeotropic distillation (112). Another procedure for the preparation of butyl acrylate, secondary alkyl acrylates, and hydroxyalkyl acrylates using -toluenesulfonic acid as a catalyst has been described (113). Alurninumisopropoxide catalyzes the reaction of amino alcohols with methyl acrylate and methyl methacrylate. A review of the synthesis of acryhc esters by transesterification is given in Reference 114 (see... 

The first methacrylic esters were prepared by dehydration of hydroxyisobutyric esters, prohibitively expensive starting points for commercial synthesis. In 1932 J. W. C. Crawford discovered a new route to the monomer using cheap and readily available chemicals—acetone, hydrocyanic acid, methanol and sulphuric acid— and it is his process which has been used, with minor modifications, throughout the world. Sheet poly(methyl methacrylate) became prominent during World War II for aircraft glazing, a use predicted by Hill in his early patents, and since then has found other applications in many fields. 

When the polymer was prepared by the suspension polymerization technique, the product was crosslinked beads of unusually uniform size (see Fig. 16 for SEM picture of the beads) with hydrophobic surface characteristics. This shows that cardanyl acrylate/methacry-late can be used as comonomers-cum-cross-linking agents in vinyl polymerizations. This further gives rise to more opportunities to prepare polymer supports for synthesis particularly for experiments in solid-state peptide synthesis. Polymer supports based on activated acrylates have recently been reported to be useful in supported organic reactions, metal ion separation, etc. [198,199]. Copolymers are expected to give better performance and, hence, coplymers of CA and CM A with methyl methacrylate (MMA), styrene (St), and acrylonitrile (AN) were prepared and characterized [196,197]. 

The synthesis of isotactic and syndiotactic polymers has been achieved for a number of polymers. For example poly (methyl methacrylate) can be prepared in either isotactic or syndiotactic configurations depending on the details of the polymerisation conditions. 

---