Standards inspections

Once the feasibility of using real time X-ray as an inspection method was established, it was decided to proceed with the design of a system equally suited for control of incoming frozen fish blocks and for developing inspection procedures. These inspection procedures are, when completed, to be the basis of the inspection standards for the complete concern. 

It is to be taken into account that there is a difference between ultrasonic and radiography defect imaging, so the ultrasonic image recognition knowledge required for the person interpreting the inspection results. The ISONIC postprocessing mode allows to ease sueh interpretation because it s maximally approached to inspection standards. 

The pulse-echo and resonance impedance techniques are capable of determining which layer contains a disbond, given an appropriate standard to compare against. Inspection standards are bond assemblies made to simulate specific areas of a part with disbonds purposefully placed in them. By comparing the signal response of a suspected void to that of a known disbond in the standard, the... 

Define the inspection aids and test equipment to be used. There may be jigs, fixtures, gages, and other aids needed for inspection. Standard measuring equipment would not need to be specified as your inspectors and testers should be trained to select the right tools for the job. Any special test equipment should be identified. 

The remaining latex is processed into dry rubber as sheets, crepes and bales. There is an International Standard for the Quality and Packing for Natural Rubber grades, the so-called Green Book , published by the Rubber Manufacturers Association. The following grades of NR listed in the Green Book are sold to visual inspection standards only ... 

Has all equipment been inspected as scheduled Yes. The maintenance personnel have inspected the equipment in the process area according to company inspection standards. 

Provincial legislation provides inspection standards for agrifood products, including dairy, meat, and honey. These responsibilities include provision of... 

The concept behind the MRA is that one regulatory authority will accept the findings of another authority with confidence in the rigor of the inspection process and hence negate the reason to conduct its own inspection of the same pharmaceutical or healthcare company. This is all good theory but requires harmonized inspection standards, practices, reporting, and training. 

The region in which the blasting is done must be kept well protected by rock dust or otherwise be in accordance with Bureau of Mines inspection standards. 

In order to prevent corrosion loss, it is very important to inspect the coating condition inside the ballast tank of ship, such as oil tankers, LNG ships and cargo ships. The current inspection standard defines that the ratio of paint defect surface area in the total surface is visually inspected every two or three years periodically. However, the current visual inspection has some problems, such as the dangerous and dark environment for inspectors, the inaccurate evaluation result depending on the inspector s skill and the time consuming and heavy labor required in order to inspect all the hundreds of tank compartments. In order to overcome these issues,... 

Standard procedures for self inspection. Standard procedures for product recalls. Standard procedures for handling of complaints, including adverse reaction reports. 

Inspection Standard data, MTM-2, Work-Factor, MOST, macromotion analyses... 

At the rule-based level, there are typicaUy changes in the setup to accommodate different customers, different products, or different process conditions. Thus, in Drury and Kleiner (1990), a job aid was produced to help inspectors of roUer bearings reason more effectively from customer specifications to choice of inspection standards. In aircraft-structure inspection, the calibration of an eddy-current meter must be changed by knovm rules to accommodate different thicknesses of fuselage skin or detect cracks of different depths. Errors at this level consist of misapplication of rules. 

Acceptance check similarly, standard hidden danger table —if there are any relative records in it provides inspection standards for factor checkers. The danger information will be submitted and wait to be eliminated if the rectification result is qualified, or it would be returned for a second time rectification. 

CFR Appendix G to Subchapter B — Minimum Periodic Inspection Standards... 

This paper briefly describes a typical RPV then deals with Codes formulated for Inspecting these vessels. Although European RPV s are not bound by the rules of the American Society of Mechanical Engineers (ASME) the inspection standards required generally follow the ASME pattern. The types of equipment and techniques developed at RPIS, as inspection rules have changed, are discussed. 

Criteria based on a combination of material testing, calculation of applied stresses and workmanship/inspection standards. These are intended to demonstrate that a sufficient margin exists between the calculated design state and the measured material response state. 

Would your vehicles pass the minimum periodic inspection standards set out by the FMCSR ... 

Vice-President Gore s National Performance Review of Government proposed that employers either hire inspectors from private inspection firms or have employees trained and certified to conduct inspections (Salwin 1993). OSH A would set private inspection standards and conduct random reviews of the private inspections. The suggestion for self inspection is in response to the Gore committee s conclusion that OSHA is unable to inspect and enforce standards adequately without impossibly high increases in funding (Occupational Hazards 1993a). 

Regardless of organization structure, food service operations require a number of workers including cooks, food handlers, and sanitation workers. These workers can experience a wide variety of safety and health risks. Food service departments must meet inspection standards of the local health department. They must also comply with state and federal safety requirements. 

Each situation dictates who qualifies to conduct an inspection. Inspectors can be workers, co-workers, supervisors, specialists (engineers, safety specialists and others), or special teams. In some cases, inspectors need certification for the inspections they perform. Recertification is also important to assure that inspection skills are current and meet inspection standards. 

The PMP must be enforced by management. It should also be evaluated continuously to gauge it effectiveness in preventing accidents. Your fleet of vehicles should be capable of passing the minimum industry inspection standards. 

If the vehicle is based in a state that has an annual mandatory vehicle inspection program covering the vehicle, the state inspection can be used in place of the federal annual/ periodic inspection. In this case, the technician and inspection standards are determined by the state. 

If precise hole size tolerance is required, the clearance between punch and die should be very close the die hole should be only 0.002 to 0.004 in. larger than the punch for paper-based materials (Rg. 35.2 and Table 35.2). Glass-based laminates generally require about one-half that tolerance. Dies have, however, been constructed with as much as 0.010 in. all-around clearance between punch and die. They are for use where inspection standards permit rough-quality holes. 

This section examines inspection requirements and can serve as general guidance to cylinder owners, fillers, shippers, and users concerning the considerations involved in setting up visual inspection standard operating procedures to ensure that cylinders which do not meet the criteria for continued service will not be inadvertently returned to service. 

---