Together Pressing

Traditional solid-state synthesis involves the direct reaction of stoichiometric quantities of pure elements and precursors in the solid state, at relatively high temperatures (ca. 1,000 °C). Briefly, reactants are measured out in a specific ratio, ground together, pressed into a pellet, and heated in order to facilitate interdiffusion and compound formation. The products are often in powdery and multiphase form, and prolonged annealing is necessary in order to manufacture larger crystals and pure end-products. In this manner, thermodynamically stable products under the reaction conditions are obtained, while rational design of desired products is limited, as little, if any, control is possible over the formation of metastable intermediates. ... 

Brugfeie Powder. A proplnt used with some success in France for the Chassepot rifle. It was prepd by grinding together, pressing and granulating as in the manuf of BkPdr, a mixt of Amm pic rate 54 Sc KN03 46%. It was more powerful than BkPdr and gave less smoke Refs l)Daniel(1902), 86 2)Marshall 1(1917),... 

Soft-wheat flours are sold for general family use, as biscuit or cake flours, and for the commercial production of crackers, pretzels, cakes, cookies, and pastry. The protein in soft wheat flour mns from 7 to 10%. There are differences in appearance, texture, and absorption capacity between hard- and soft-wheat flour subjected to the same milling procedures. Hard-wheat flour falls into separate particles if shaken in the hand whereas, soft-wheat flour tends to clump and hold its shape if pressed together. Hard-wheat flour feels slightly coarse and granular when mbbed between the fingers soft-wheat flour feels soft and smooth. Hard-wheat flour absorbs more Hquid than does soft-wheat flour. Consequently, many recipes recommend a variable measure of either flour or Hquid to achieve a desired consistency. 

Pressing and sintering together determine the size and shape of the final product, but these are not well controlled with respect to the critical parts which determine the airgap in the magnetic circuit. For that reason a finishing touch by machining is necessary. 

Tack. Tack causes layers to adhere when they are pressed together. This property can be reduced by employing fillers with a finer psd or by dusting the stock with a laminar filler such as mica. In a related value, fillers such as mica can inhibit adhesion to the mold during processing. 

Plate-and-Frame Filter Presses. In the conventional plate-and-frame press (Fig. 14), a sequence of perforated square, or rectangular, plates alternating with hoUow frames is mounted on suitable supports and pressed together with hydrauHc or screw-driven rams. The plates are covered with a filter cloth which also forms the sealing gasket. The slurry is pumped iato the frames and the filtrate is drained from the plates. 

Ethylene—tetrafluoroethylene copolymers respond weU to melt bonding to untreated aluminum, steel, and copper with peel strengths above 3.5 kN/m (20 Ibf/in.). Eor melt bonding to itself, hot-plate welding is used. The material is heated to 271—276°C, and the parts are pressed together during cooling. 

During the press operation, which is actually a form of compression mol ding, the resin-treated laminate pHes are heated under pressure and the resins cured. The initial heating phases cause the resin to melt and flow into voids in the reinforcing ply and bond the individual pHes together. The appHed heat simultaneously causes the resin to polymerize and eventually to cross-link or gel. Therefore, resin viscosity reaches a minimum during the press cycle. This is the point at which the curing process becomes dominant over the melt flow process. Dynamic mechanical and dielectric analyses (11) are excellent tools for study of this behavior. 

Mica splittings are processed from lower quaUty blocks and from sheets too thin for blocks and unsatisfactory for producing film. The splittings are packed for sale in three ways book form, which are laminae spHt to the desired thickness from the same book of mica, then dusted with mica dust, and restacked in book form pan packed, in which splitting layers are placed evenly in a pan, and each layer separated by a thin sheet of paper then pressed together and loose packed, in which splittings are si2ed with screens then padded loosely in a wooden box for shipment. 

The stainless steel plates are separated (ca 3 pm between) by nonabsorbent vulcanized gaskets. Various profiles and configurations, including raised knobs, crescents, channels, or diamonds, provide a rapid, uniform heat-transfer plate surface. During operation the plates must be pressed together to provide a seal, and mounted and coimected in such a manner that air is eliminated and that the product drains from the plates without opening. 

Paper consists of sheet materials that are comprised of bonded small discrete fibers. The fibers usually are ceUulosic in nature and are held together by hydrogen bonds (see Cellulose). The fibers are formed into a sheet on a fine screen from a dilute water suspension. The word paper is derived from papyms, a sheet made in ancient times by pressing together very thin strips of an Egyptian reed Cjperuspapyrus) (1). 

The disk refiner, a newer development used for fine paper grades, includes one or two rotary disks and two or four working surfaces. The surfaces are pressed together uniformly by hydraulic pressure and guided by high precision, heavy-duty bearing systems. Stock usuaUy is fed through the center of one plate and leaves between the plates at their circumferences. 

The materials used in a total joint replacement ate designed to enable the joint to function normally. The artificial components ate generally composed of a metal piece that fits closely into bone tissue. The metals ate varied and include stainless steel or alloys of cobalt, chrome, and titanium. The plastic material used in implants is a polyethylene that is extremely durable and wear-resistant. Also, a bone cement, a methacrylate, is often used to anchor the artificial joint materials into the bone. Cementiess joint replacements have mote tecentiy been developed. In these replacements, the prosthesis and the bone ate made to fit together without the need for bone cement. The implants ate press-fit into the bone. 

---