Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Fixed fluidized-bed reactors

Figure 2. Conversion and octane measured in a fixed fluidized bed reactor, 40 C/0, 30 WHSV, 510 using USY catalyst, 0.2% Na on zeolite. Figure 2. Conversion and octane measured in a fixed fluidized bed reactor, 40 C/0, 30 WHSV, 510 using USY catalyst, 0.2% Na on zeolite.
Gasoline Compositions and Yields (Fixed Fluidized Bed Reactor Tests)... [Pg.107]

Esso-type stable fixed fluidized-bed reactor/regenerator is used for cracking petroleum oils (Fig. 19-23h). [Pg.34]

Li, H., Yu, P., Shen, B., 2009. Biofuel potential production from cottonseed oil a comparison of non-catalytic and catalytic pyrolysis on fixed-fluidized bed reactor. Fuel Processing Technology 90 (9), 1087—1092. [Pg.424]

Fluidized-bed catalytic reactors. In fluidized-bed reactors, solid material in the form of fine particles is held in suspension by the upward flow of the reacting fluid. The effect of the rapid motion of the particles is good heat transfer and temperature uniformity. This prevents the formation of the hot spots that can occur with fixed-bed reactors. [Pg.58]

Recent advances in Eischer-Tropsch technology at Sasol include the demonstration of the slurry-bed Eischer-Tropsch process and the new generation Sasol Advanced Synthol (SAS) Reactor, which is a classical fluidized-bed reactor design. The slurry-bed reactor is considered a superior alternative to the Arge tubular fixed-bed reactor. Commercial implementation of a slurry-bed design requires development of efficient catalyst separation techniques. Sasol has developed proprietary technology that provides satisfactory separation of wax and soHd catalyst, and a commercial-scale reactor is being commissioned in the first half of 1993. [Pg.164]

More recently, Sasol commercialized a new type of fluidized-bed reactor and was also operating a higher pressure commercial fixed-bed reactor (38). In 1989, a commercial scale fixed fluid-bed reactor was commissioned having a capacity similar to existing commercial reactors at Sasol One (39). This effort is aimed at expanded production of higher value chemicals, in particular waxes (qv) and linear olefins. [Pg.81]

In oxychlorination, ethylene reacts with dry HCl and either air or pure oxygen to produce EDC and water. Various commercial oxychlorination processes differ from one another to some extent because they were developed independentiy by several different vinyl chloride producers (78,83), but in each case the reaction is carried out in the vapor phase in either a fixed- or fluidized-bed reactor containing a modified Deacon catalyst. Unlike the Deacon process for chlorine production, oxychlorination of ethylene occurs readily at temperatures weU below those requited for HCl oxidation. [Pg.417]

Sasol uses both fixed-bed reactors and transported fluidized-bed reactors to convert synthesis gas to hydrocarbons. The multitubular, water-cooled fixed-bed reactors were designed by Lurgi and Ruhrchemie, whereas the newer fluidized-bed reactors scaled up from a pilot unit by Kellogg are now known as Sasol Synthol reactors. The two reactor types use different iron-based catalysts and give different product distributions. [Pg.199]

The Fischer-Tropsch reaction is highly exothermic. Therefore, adequate heat removal is critical. High temperatures residt in high yields of methane, as well as coking and sintering of the catalyst. Three types of reac tors (tubular fixed bed, fluidized bed, and slurry) provide good temperature control, and all three types are being used for synthesis gas conversion. The first plants used tubular or plate-type fixed-bed reactors. Later, SASOL, in South Africa, used fluidized-bed reactors, and most recently, slurry reactors have come into use. [Pg.2377]

SASOL has pursued the development of alternative reactors to overcome specific operational difficulties encountered with the fixed-bed and entrained-bed reactors. After several years of attempts to overcome the high catalyst circulation rates and consequent abrasion in the Synthol reactors, a bubbling fluidized-bed reactor 1 m (3.3 ft) in diameter was constructed in 1983. Following successflil testing, SASOL designed and construc ted a full-scale commercial reac tor 5 m (16.4 ft) in diameter. The reactor was successfully commissioned in 1989 and remains in operation. [Pg.2377]

As mentioned in Section 2.2 (Fixed-Bed Reactors) and in the Micro activity test example, even fluid-bed catalysts are tested in fixed-bed reactors when working on a small scale. The reason is that the experimental conditions in laboratory fluidized-bed reactors can not even approach that in production units. Even catalyst particle size must be much smaller to get proper fluidization. The reactors of ARCO (Wachtel, et al, 1972) and that of Kraemer and deLasa (1988) are such attempts. [Pg.42]

A salient feature of the fluidized bed reactor is that it operates at nearly constant temperature and is, therefore, easy to control. Also, there is no opportunity for hot spots (a condition where a small increase in the wall temperature causes the temperature in a certain region of the reactor to increase rapidly, resulting in uncontrollable reactions) to develop as in the case of the fixed bed reactor. However, the fluidized bed is not as flexible as the fixed bed in adding or removing heat. The loss of catalyst due to carryover with the gas stream from the reactor and regenerator may cause problems. In this case, particle attrition reduces their size to such an extent where they are no longer fluidized, but instead flow with the gas stream. If this occurs, cyclone separators placed in the effluent lines from the reactor and the regenerator can recover the fine particles. These cyclones remove the majority of the entrained equilibrium size catalyst particles and smaller fines. The catalyst fines are attrition products caused by... [Pg.234]

For the manufacturing of sulfosuccinic acid esters, which belong to a special class of surfactants, maleic acid anhydride is needed. Maleic acid anhydride is an important intermediate chemical of the chemical industry. Its worldwide output amounts to about 800,000 tons (1990) [64]. Maleic acid is produced by catalytic vapor phase oxidation process of benzene or n-C4 hydrocarbons in fixed bed or fluidized bed reactors according the following reaction equations. The heat of reaction of the exothermic oxidation processes is very high. [Pg.33]

The effects of the inlet TCE concentration on the ftotodegradation in the fluidized bed reactor are shown in Fig. 3. As shown, the gas stream with the lower inlet concentration of TCE has a higher removal efficiency. This means that limited and fixed amounts of active sites on the TiCb/SiCb are present in the fluidized bed reactor system... [Pg.583]

In any catalyst selection procedure the first step will be the search for an active phase, be it a. solid or complexes in a. solution. For heterogeneous catalysis the. second step is also deeisive for the success of process development the choice of the optimal particle morphology. The choice of catalyst morphology (size, shape, porous texture, activity distribution, etc.) depends on intrinsic reaction kinetics as well as on diffusion rates of reactants and products. The catalyst cannot be cho.sen independently of the reactor type, because different reactor types place different demands on the catalyst. For instance, fixed-bed reactors require relatively large particles to minimize the pressure drop, while in fluidized-bed reactors relatively small particles must be used. However, an optimal choice is possible within the limits set by the reactor type. [Pg.84]

Applications of the organic solvents in fluidized-bed reactors have also been investigated, particularly with immobilized cells (Table 5). This type of reactor has several advantages over a fixed-bed reactor, namely, reduced coalescence of the emulsion particles, lower pressure at high flow rate, and less channeling and plugging. [Pg.581]

The average pore size and the pore size distribution should be such that physical limitations are not placed on the conversion of reactants to products. The particle size of the carrier must also be suitable for the purpose intended (i.e., small for fluidized bed reactors and significantly larger for fixed bed applications). [Pg.200]

In the sections that follow, each of these reactor classes is discussed in more detail, with particular emphasis on fixed and fluidized bed reactors. [Pg.425]


See other pages where Fixed fluidized-bed reactors is mentioned: [Pg.21]    [Pg.345]    [Pg.506]    [Pg.21]    [Pg.2636]    [Pg.447]    [Pg.2615]    [Pg.410]    [Pg.275]    [Pg.281]    [Pg.21]    [Pg.345]    [Pg.506]    [Pg.21]    [Pg.2636]    [Pg.447]    [Pg.2615]    [Pg.410]    [Pg.275]    [Pg.281]    [Pg.22]    [Pg.456]    [Pg.519]    [Pg.418]    [Pg.418]    [Pg.160]    [Pg.170]    [Pg.466]    [Pg.277]    [Pg.514]    [Pg.44]    [Pg.88]    [Pg.1258]    [Pg.194]    [Pg.88]    [Pg.428]   
See also in sourсe #XX -- [ Pg.37 ]

See also in sourсe #XX -- [ Pg.37 ]




SEARCH



FLUIDIZED AND FIXED BED REACTORS

Fluidized reactors

© 2024 chempedia.info