Electrooxidation

Other recovery methods have been used (10). These include leaching ores and concentrates using sodium sulfide [1313-82-2] and sodium hydroxide [1310-73-2] and subsequentiy precipitating with aluminum [7429-90-3], or by electrolysis (11). In another process, the mercury in the ore is dissolved by a sodium hypochlorite [7681-52-9] solution, the mercury-laden solution is then passed through activated carbon [7440-44-0] to absorb the mercury, and the activated carbon heated to produce mercury metal. Mercury can be extracted from cinnabar by electrooxidation (12,13). 

An electrooxidation process was developed by Asahi Chemical Industry ia Japan, and was also piloted by BASF ia Germany. It produces high purity sebacic acid from readily available adipic acid. The process consists of 3 steps. Adipic acid is partially esterified to the monomethyl adipate. Electrolysis of the potassium salt of monomethyl adipate ia a mixture of methanol and water gives dimethyl sebacate. The last step is the hydrolysis of dimethyl sebacate to sebacic acid. Overall yields are reported to be about 85% (65). 

ELECTROOXIDATION, QUANTUM CHEMICAL CALCULATIONS AND CHEMILUMINESCENT ANALYSIS OF DIHYDROPYRIDINES DERIVATIVES... 

It is known that tropylium may be prepared from tropylidene via hydride abstraction by PhgC or MegC carbonium ions therefore, it is very likely that here too the dehydrogenation is a hydride transfer from the 1,5-dione to an acceptor. A similar dehydrogenation of chromanones to chromones, with triphenylmethyl perchlorate was reported. A study of the electrooxidation of 1,5-diones on a rotating platinum electrode showed that 1,5-diaryl-substituted diones afford pyrylium salts in these conditions and that the half-wave potentials correlate with yields in chemical dehydrogenations. 

The oxidation of the deposited germanium is also a complicated process we found that mainly chemical oxidation by Gel4 takes place, together with some electrooxidation. It is likely that kinetic factors play a dominant role. 

Stereoselective conversion of a thiane 57 to the corresponding tmns-thiane-l-oxide 58 was achieved by bromonium ion mediated electrooxidation while a preferential formation of the cis-sulphoxide 58 was observed under acidic electrolysis123 (equation 38). 

Menke EJ, Brown MA, Li Q, Hemminger JC, Penner RM (2006) Bismuth telluride (Bi2Te3) nanowires Synthesis by cyclic electrodeposition/stripping, thinning by electrooxidation, and electrical power generation. Langmuir 22 10564-10574... 

Therefore the overall efficiency may be dramatically decreased, e.g., if the electrooxidation stops at the formaldehyde stage ... 

From the results obtained with in situ reflectance spectroscopy and on-line analytical methods, investigators at Universite de Poitiers proposed a complete mechanism for the electrooxidation of methanol at a platinum electrode. The first step of the electrooxidation reaction is the dissociative adsorption of methanol, leading to several species according to the following equations ... 

The crucial aspect is thus to determine the fate of the ( CHO), species. Possible mechanisms for its oxidative removal are schematically shown in Fig. 9. From this scheme, it appears that the desorption of the formyl species can follow different pathways through competitive reactions. This schematic illustrates the main problems and challenges in improving the kinetics of the electrooxidation of methanol. On a pure platinum surface, step (21) is spontaneously favored, since the formation of adsorbed CO is a fast process, even at low potentials. Thus, the coverage... 

Platinum is the only acceptable electrocatalyst for most of the primary intermediate steps in the electrooxidation of methanol. It allows the dissociation of the methanol molecule hy breaking the C-H bonds during the adsorption steps. However, as seen earlier, this dissociation leads spontaneously to the formation of CO, which is due to its strong adsorption on Pt this species is a catalyst poison for the subsequent steps in the overall reaction of electrooxidation of CHjOH. The adsorption properties of the platinum surface must be modified to improve the kinetics of the overall reaction and hence to remove the poisoning species. Two different consequences can be envisaged from this modification prevention of the formation of the strongly adsorbed species, or increasing the kinetics of its oxidation. Such a modification will have an effect on the kinetics of steps (23) and (24) instead of step (21) in the first case and of step (26) in the second case. 

The rate-determining step (rds) of the reaction on platinum is the oxidation of adsorbed CO with adsorbed hydroxyl species [step (26)]. The current density of the methanol electrooxidation can be obtained from the following equatiorf ... 

Since oxidation of methanol is an electrocatalytic reaction with different adsorption steps, interactions of the adsorbed species with the metallic surface are important. Using platinum single-crystal electrodes, it has been proven that the electrooxidation of methanol is a surface-sensitive reaction. The initial activity of the Pt(llO) plane is much higher than that of the other low-index planes, but the poisoning phenomenon is so rapid that it causes a fast decrease in the current densities. The... 

The effects of dispersion of the electrocatalyst and of particle size on the kinetics of electrooxidation of methanol have been the subject of numerous studies because of the utilization of carbon support in DMFC anodes. The main objective is to determine the optimum size of the platinum anode particles in order to increase the effectiveness factor of platinum. Such a size effect, which is widely recognized in the case of the reduction of oxygen, is still a subject of discussion for the oxidation of methanol. According to some investigators, an optimum of 2 nm for the platinum particle size exists, but studying particle sizes up to 1.4 nm, other authors observed no size effect. According to a recent study, the rate of oxidation of methanol remains constant for particles greater than 4.5 nm, but decreases with size for smaller particles (up to 2.2 nm). 

Such information can be obtained from cyclic voltammetric measme-ments. It is possible to determine the quantity of electricity involved in the adsorption of hydrogen, or for the electrooxidation of previously adsorbed CO, and then to estimate the real surface area and the roughness factor (y) of a R-C electrode. From the real surface area and the R loading, it is possible to estimate the specific surface area, S (in m g ), as follows ... 

A third way to increase both the active surface area and the number of oxygenated species at the electrode surface is to prepare alloy particles or deposits and then to dissolve the non-noble metal component. This technique, which is similar to that used to prepare Raney-type catalysts, yields very high surface area electrodes and hence some improvements in the electrocatalytic activities compared with those of pure platinum. However, it is always difficult to be sure whether the mechanism of enhancment of the activities is due to this effect or the possible presence of remaining traces of the dissolved metal. Results with PtyCr and PtSFe were encouraging, although the effect of iron is still under discussion. From studies in a recent work on the behavior of R-Fe particles for methanol electrooxidation, it was concluded that the electrocatalytic effect is due to the Fe alloyed to platinum. ... 

The use of adatoms of foreign metals obtained by imderpotential deposition on the platinum surface is another convenient method for investigating the effect of a promoter on the electrocatalytic properties of platinum. However, the effect of adatoms in this case has been shown to be not as effective for electrooxidation of methanol as for the oxidation of other organic molecules such as formic acid adatoms of tin, however, showed a positive effect on the rate of methanol oxidation. ... 

In addition to these different types of alloys, some studies were also devoted to alternatives to platinum as electrocatalysts. Unfortunately, it is clear that even if some catalytic activities were observed, they are far from those obtained with platinum. Nickel tungsten carbides were investigated, but the electrocatalytic activity recorded for methanol oxidation was very low. Tungsten carbide was also considered as a possible alternative owing to its ability to catalyze the electrooxidation of hydrogen. However, it had no activity for the oxidation of methanol and recently some groups showed that a codeposit of Pt and WO3 led to an enhancement of the activity of platinum. ... 

The mechanism of electrooxidation of methanol is now nearly well understood. From the considerable effort made during the past 20 years, it is now possible to propose electrocatalysts with acceptable activities for DMFCs, even though further improvement is still necessary. Despite considerable research efforts, R-Ru alloys are the only acceptable catalysts for the electrooxidation of methanol at low anode potentials. Two questions still remain unanswered ... 

The extensive state of knowledge of the electrooxidation of methanol, as presented in this section, offers prospects of tailoring new multimetallic... 

---