Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Nonaqueous Electrolyte Solutions

Most 2,5-unsubstituted pyrroles and thiophenes, and most anilines can be polymerized by electrochemical oxidation. For pyrroles, acetonitrile,54 or aqueous55 electrolyte solutions are normally used, while the polymerization of thiophenes is performed almost exclusively in nonaqueous solvents such as acetonitrile, propylene carbonate, and benzonitrile. 0 Polyanilines are generally prepared from a solution of aniline in aqueous acid.21 Platinum or carbon electrodes have been used in most work, although indium-tin oxide is routinely used for spectroelectrochemical experiments, and many other electrode materials have also been employed.20,21... [Pg.554]

Barthel, J. Temperature Dependence of Conductance of Electrolytes in Nonaqueous Solutions 13... [Pg.600]

The influence of interfaeial potentials (diffusion or liquid junction potentials) established at the boundary between two different electrolyte solutions (based on e.g. aqueous and nonaqueous solvents) has been investigated frequently, for a thorough overview see Jakuszewski and Woszezak [68Jak2]. Concerning the usage of absolute and international Volt see preceding chapter. [Pg.55]

Nonaqueous electrolyte solutions are analogous to aqueous solutions they, too, are systems with a liquid solvent and a solute or solutes dissociating and forming solvated ions. The special features of water as a solvent are its high polarity, e = 78.5, which promotes dissocation of dissolved electrolytes and hydration of the ions, and its protolytic reactivity. When considering these features, we can group the nonaqueous solvents as follows ... [Pg.128]

NONAQUEOUS ELECTROLYTE SOLUTIONS 129 TABLE 8.1 Physical Properties of Certain Solvents at 25°C... [Pg.129]

In aqueous electrolyte solutions the molar conductivities of the electrolyte. A, and of individual ions, Xj, always increase with decreasing solute concentration [cf. Eq. (7.11) for solutions of weak electrolytes, and Eq. (7.14) for solutions of strong electrolytes]. In nonaqueous solutions even this rule fails, and in some cases maxima and minima appear in the plots of A vs. c (Eig. 8.1). This tendency becomes stronger in solvents with low permittivity. This anomalons behavior of the nonaqueous solutions can be explained in terms of the various equilibria for ionic association (ion pairs or triplets) and complex formation. It is for the same reason that concentration changes often cause a drastic change in transport numbers of individual ions, which in some cases even assume values less than zero or more than unity. [Pg.130]

Electrochemical reduction of carbon dioxide is usually conducted in aqueous or nonaqueous electrolyte solutions at cathodes made of various materials. As a result, various organic substances can form. The most common reactions are as follows ... [Pg.291]

For all these reasons, the stability of the superconducting state and ways to control it are questions of prime importance. Many studies have addressed the degradation of the properties of HTSC under the influence of a variety of factors. They included more particularly the corrosion resistance of HTSC materials exposed to aqueous and nonaqueous electrolyte solutions as well as to water vapor and the vapors of other solvents. It was seen that the corrosion resistance depends strongly both on the nature (chemical composition, structure, etc.) of the HTSC materials themselves and on the nature of the aggressive medium. [Pg.631]

Before considering different theoretical approaches to determining the free energies and other thermodynamic properties of ionic solvation, it is important to be aware of a problem on the experimental level. There are several methods available for obtaining these quantities for electrolyte solutions, both aqueous and nonaqueous some of these have been described by Conway and Bockris162 and by Padova.163 For example, enthalpies of solvation can be found via thermodynamic cycles, free energies from solubilities or galvanic cell potentials. However the results... [Pg.59]

Electrolytes are ubiquitous and indispensable in all electrochemical devices, and their basic function is independent of the much diversified chemistries and applications of these devices. In this sense, the role of electrolytes in electrolytic cells, capacitors, fuel cells, or batteries would remain the same to serve as the medium for the transfer of charges, which are in the form of ions, between a pair of electrodes. The vast majority of the electrolytes are electrolytic solution-types that consist of salts (also called electrolyte solutes ) dissolved in solvents, either water (aqueous) or organic molecules (nonaqueous), and are in a liquid state in the service-temperature range. [Although nonaqueous has been used overwhelmingly in the literature, aprotic would be a more precise term. Either anhydrous ammonia or ethanol qualifies as a nonaqueous solvent but is unstable with lithium because of the active protons. Nevertheless, this review will conform to the convention and use nonaqueous in place of aprotic .]... [Pg.64]

An ideal electrolyte solute for ambient rechargeable lithium batteries should meet the following minimal requirements (1) It should be able to completely dissolve and dissociate in the nonaqueous media, and the solvated ions (especially lithium cation) should be able to move in the media with high mobility. (2) The anion should be stable against oxidative decomposition at the cathode. (3) The anion should be inert to electrolyte solvents. (4) Both the anion and the cation should remain inert toward the other cell components such as separator, electrode substrate. [Pg.71]

Handa et al. reported the synthesis of a phosphorus equivalent of Barthel s salts in which the hexavalent phosphorus(V) was coordinated by three bidentate ligands. 1.2-benzenediolato-O.C7. Its thermal stability is similar to that of its boron counterparts, and moderate ion conductivity was achieved in nonaqueous media. The authors attributed the less-than-satisfactory ion conduction to the large size of the anions, which increased the viscosity of the resultant electrolyte solutions. The anodic stability limit, as measured by voltammetry on a Ni electrode, was below 3.7 V. A preliminary test of this salt in EC/ THF was conducted in a lithium cell using the low potential cathode. V2O5. and the authors believed that this salt could be a superior electrolyte solute, judging from the utilized cell capacity that was close to the theoretical value. [Pg.149]

J. Barthel, Nonaqueous electrolyte solutions in chemistry and modem technology in Topics in Current Chemistry (Ed. F. L. [Pg.349]

The most stable oxidation states for protactinium are Pa(V) and Pa(IV). The chemical behavior of Pa(V) closely mimics that of Nb(V) and Ta(V), and experimental data are consistent with a 5f(l) rather than a 6d(l) electron configuration for the Pa(IV) species [37]. The electrochemical literature for Pa is mainly focused on the characteristics of the Pa(V)/Pa(IV) couple and the electrodeposition of Pa metal films from aqueous and nonaqueous electrolyte solutions. In aqueous solutions, only Pa(V) and Pa(IV) ions are known to exist, and the standard potential for the Pa(V)/Pa(IV) redox couple is in the range of —0.1 to -0.32 V [38]. [Pg.1054]

Semiaqueous or Nonaqueous Solutions. Although the measurement of pH in mixed solvents (e.g., water/organic solvent) is not recommended, for a solution containing more than 5% water, the classical definition of a pH measurement may still apply. In nonaqueous solution, only relative pH values can be obtained. Measurements taken in nonaqueous or partly aqueous solutions require the electrode to be frequently rehydrated (i.e soaked in water or an acidic buffer). Between measurements and after use with a nonaqueous solvent (which is immiscible with water), the electrode should first be rinsed with a solvent, which is miscible with water as well as the analyte solvent, then rinsed with water. Another potential problem with this type of medium is the risk of precipitation of the KC1 electrolyte in the junction between the reference electrode and the measuring solution. To minimize this problem, the reference electrolyte and the sample solution should be matched for mobility and solubility. For example, LiCl in ethanol or LiCl in acetic acid are often used as the reference electrode electrolyte for nonaqueous measurements. [Pg.239]

Ionics, 2nd edn, Plenum Press, New York, 1998 (b) Barthel, [.M.G., Krienke, H., Kunz, W. Physical Chemistry of Electrolyte Solutions, Modern Aspects, Springer, Darmstadt, 1998 (c) Maman-tov, G., Popov, A. I. (Eds) Chemistry of Nonaqueous Solutions, Current Progress, VCH, Weinheim, 1994, Chapters 1-3. [Pg.59]

The heats of solution and dilution of electrolytes in nonaqueous-aqueous solvent mixtures have been limited mostly to alcohol-water systems and a few measurements in dimethylsulfoxide-water and dioxane-water mixtures (J, 2). The structural maximum in aqueous-organic solvents at high water content has been well established by a variety of techniques (3,4), but few systems have been explored over the whole composition range. [Pg.300]


See other pages where Nonaqueous Electrolyte Solutions is mentioned: [Pg.1372]    [Pg.1372]    [Pg.437]    [Pg.348]    [Pg.177]    [Pg.39]    [Pg.107]    [Pg.603]    [Pg.248]    [Pg.251]    [Pg.259]    [Pg.127]    [Pg.128]    [Pg.293]    [Pg.372]    [Pg.380]    [Pg.385]    [Pg.318]    [Pg.321]    [Pg.328]    [Pg.73]    [Pg.89]    [Pg.112]    [Pg.144]    [Pg.155]    [Pg.167]    [Pg.182]    [Pg.291]    [Pg.267]   
See also in sourсe #XX -- [ Pg.640 ]




SEARCH



Advantages and Disadvantages of Nonaqueous Electrolyte Solutions

Electrolyte solutions

Electrolytes Based on Aprotic Nonaqueous Solutions

Electrolytes nonaqueous

Electrolytic solution

Nonaqueous

Solution electrolyte solutes

© 2024 chempedia.info