Data sheet, sample

These consist of field data sheets, sample storage records, bench sheets or laboratory notebooks, chromatograms, and shipping papers. Some of the laboratory records, in particular, can be electronic rather than paper. 

Appendices. Appendices contain details needed to support your results and to be used by people who may continue your work. Make it easy for them by organizing the material under subtitles or sub-appendices listed in the table of contents. Use enough words in appendices to define units and manipulations, but do not worry about smooth text with introductions and transitions. Include data sheets, sample calculations including error propagation, tables of intermediate variables in the calculations, working plots, calibration curves, and all the figures and tables that you did not include in the main body. 

Manufacturer verification" describes the measurement method of flaw charaeteristics. These characteristies are reported on the data sheet delivered with the equipment. Measurements are performed on a representative sample of flaw deteetors produeed. 

The required notification must be provided at ieast annually In writing. Acceptable forms of notice are, for example, a letter, product labeling, and product literature distributed to customers. If you are required to prepare and distribute a Material Safety Data Sheet (MSDS) for the mixture under the Occupational Safety and Health Act (OSHA) Hazard Communication Standard, your section 313 notification may be attached to the MSDS or the MSDS may be modified to include the required information. (A sample letter and recommended text for inclusion in an MSDS appear on pages E-4 and E-5 of this appendix.)... 

We have done our experiments with hectorite, which is a 2 1 smectite that develops negative layer charge by substitution of Li for Mg in the octahedral sheet.Samples were prepared by multiple exchange in 1.0 and 0.1 M CsCl solutions until essentially complete Cs-exchange was reached (97% of the interlayer cations). Temperature dependent data are essential to interpret the results, because there is rapid exchange of Cs among different interlayer sites at room temperature (RT). 

Creep rupture. Creep-rupture data are obtained in the same way as creep data except that higher stresses are used and the time is measured to failure (Figs. 2-28 and 29). The strains are sometimes recorded, but this is not necessary for creep rupture. The results are generally plotted as the log stress versus log time to failure (110). In creep-rupture tests it is the material s behavior just prior to the rupture that is of primary interest. In these tests a number of samples are subjected to different levels of constant stress, with the time to failure being determined for each stress level. General technical literature and product data sheets seldom provide a complete description of a material s behavior prior to rupture. It should include the development of any crazing and stress whitening, its strain-time... 

Pyridine and BF3 in methanol are hazardous and must be used only in a well-ventilated hood. A solvent partition after acylation helps remove residual pyridine from the sample. Material Safety Data Sheets for the derivatizing agents should be reviewed and kept readily available. 

Each data point must be transferred from data sheets into spreadsheets or databases. Verification of each datum should be performed by an individual who did not enter the data being verified. Audits of each phase of the study should be performed (i.e. preparation of collection forms, application calibration, each type of sample collection, sample transport, each type of chemical analysis, data recording, data entry, data verification and data storage). 

The thermal resistance between the ends of the sample and the copper blocks must be negligible compared with the thermal resistance of the sample. This assumption must be verified especially for short samples at low temperature where the contact resistance is higher. For this reason, a second measurement of the thermal conductivity of Torlon in the 4.2-25 K range was carried out. The second sample had a different length (L = 24.51 mm) and the same section A. This additional measurement gave the same value of k within 2%. Moreover, we see from Fig. 11.15 that data of thermal conductivity at 4.2 K well join data at lower temperatures (within 3%) obtained on a sample of much smaller geometrical factor and with a different method (integrated thermal conductivity method) and a different apparatus [38], Finally, at room temperature, we find k = 0.26 W/mK, which is the data sheet value. 

One of the most important references used during an industrial hygiene study involving toxic chemicals is the material safety data sheet (MSDS). A sample MSDS is shown in Fig-... 

High sample levels with the ion-trap detector. Finnigan MAT Application Data Sheet ADS 24. 

Fig. 8.2. Microsoft Excel data sheet for moisture in silage from the Penglais third-cut, first sampling.

There are also other tables on the data sheet that allow the easier production of charts. They refer to DM and moisture at each depth and sampling position, also the average moisture for each depth. 

In the second phase more emphasis was placed on methods development and the substances that were studied were selected from those for which validation methods were not available from the first phase. The results of these studies were presented as individual reports for each substance. They are a sampling and analytical method (SAM), a sampling data sheet (SDS), and a backup data report (BUD). The reports on methods have been published by NIOSH and are available through the U.S. Government Printing Office, Washington, D.C. 

NIOSH Manual of Sampling Data Sheets" DHEW (NIOSH)... 

While the COA is the excipient manufacturer s responsibility, once the material is received, it is the drug product manufacturers responsibility to verify the product and ensure that it is properly tested, handled, and stored. Upon receipt of a shipment, each lot of excipient will be withheld from use until the lot is sampled, tested, or examined according to the written procedures. The quality control (QC) personnel will examine each container for (i) manufacturer s name, (ii) manufacturer s lot number, (iii) leaks or spills, (iv) contamination, (v) breached containers, (vi) proper labeling, and (vii) material safety data sheet and determined material hazards. 

It is the responsibility of the operator to read and understand relevant health and safety information (e.g., material safety data sheets) before sampling. The operator must wear appropriate protective clothing for the materials to be sampled the operator should be protected from the material and the material should be protected from the operator. If specific safety precautions and equipment (e.g., respirator) are required, then the operator must be properly trained in the use of the specified equipment and procedures. 

Essentially, a user should be able to contact their excipient distributor and request a particular excipient, and the distributor should perform all of the sourcing activities, such as elucidating the exact grade of material required, if not already specified provide documentation generated by the manufacturer [product specifications or data sheets, typical C of A, material safety data sheets (MSDS)] and obtain samples of representative lots of the excipient free of charge for the user. 

When the samples are to be analyzed they are requested in writing by an analytical team leader (usually the study director). When that person takes possession of the samples, it is noted in the inventory system as well as when the samples are returned. While the samples are in the laboratory, the times and dates they are removed and returned to the laboratory freezer are recorded in the laboratory data sheets. 

In this test, a small sample of material (127 mm x 13 mm, or 5 in. x 0.5 in.) is exposed vertically to a small Bunsen burner-type flame from underneath (in the UL 94 V test) and the results show a rating, ranging from V-0 (best), through V-l, V-2 to B (for Burn). Materials with a B rating on the UL 94 Vertical test can also be tested in the less severe UL 94 HB (for horizontal burning), where the assessment is whether a flame spread rate of 4in./min is achieved. It is the most widely used fire-test specification for plastic materials, especially fire-retarded ones, and forms the basis of the famous Yellow Card used by ULs to list the plastic materials. The results from these tests are almost invariably found in a variety of specifications and data sheets. 

U. S. Department of Health, Education and Welfare, "NIOSH Manual of Sampling Data Sheets," 1977 Edition, Cincinnatti Public Health Service, 1977. 

The charcoal tube saitples were capped and labelled upon completion of sampling. Sampling data sheets were filled out listing person s name, pump number, flow rate, initial and final sampling time, and sample number. Additional information on compounds to be analyzed for and potential interferences are listed. Samples are returned to the laboratory for analysis along with a field blank. 

These physical measurements such as specific optical rotation, specific gravity and refractive index for evaluating composition and purity of an oil are widely quoted and can be read from data sheets. However, the power and value of the human nose should not be overlooked. In addition to being an important entry point for essential oils into the body, it is invaluable for making an initial examination of an oil sample. For this reason, the sense of smell and the nose and associated structures are included at this point. 

In most packages, you will enter the data from both samples into a single column of a data sheet and then set up a second column that contains labels indicating which sample each value belongs to. With the theophylline clearance data, you would place... 

Current Distribution Experiment Sample Data Sheet... 

Appendix A Data sheet Appendix B Sample calculations... 

---