Dashboard

The reverse contrast, i.e. bright characters on dark, can be achieved by orientating one polarizer parallel to tlie mbbing direction and tlie otlier one periiendicular to it, so tliat tlie device is dark in tlie off state. Backlit versions of tliis device are used in car dashboard displays [111]. [Pg.2562]

Semiflexible molded polyurethane foams are used in other automotive appHcations, such as instmment panels, dashboards, arm rests, head rests, door liners, and vibrational control devices. An important property of semiflexible foam is low resiHency and low elasticity, which results in a slow rate of recovery after deflection. The isocyanate used in the manufacture of semiflexible foams is PMDI, sometimes used in combination with TDI or TDI prepolymers. Both polyester as well as polyether polyols are used in the production of these water-blown foams. Sometimes integral skin molded foams are produced. [Pg.348]

Think of the pump curve like the dashboard or control panel of a car. No one would operate a car without the dash instrumentation panel. [Pg.76]

Indicator lights, fixed pattern, and segmented displays are applications which have been suggested for OLED deployment. Manufacturers of automobile components have shown interest in OLED indicators for the dashboard, where the primary considerations are those of cost, form factor, brightness, and stability over a wide range of ambient conditions. Power consumption is not particularly critical. The possibility of molding a thin light into a curved dashboard is attractive. [Pg.551]

Explore our innovative research tools - try the Research Dashboard now ... [Pg.1]

Mazda and others have been working on advanced safety vehicles with monitor screens to show rear and side views, voice-interactive navigation systems and collision avoidance technology. The Ford 24.7 concept car had a computer console in the dashboard with Internet access that is voice-activated. [Pg.161]

In GM s Hy-wire hydrogen powered concept vehicle, there is a fuel cell for the power source and electronics replace mechanical parts in the steering and braking systems. The driver looks through a large, sloped windshield that covers space usually taken up by an engine. There is no dashboard, instrument panel, steering wheel or pedals, only a set of adjustable footrests. [Pg.169]

Injection is by far the most used moulding process but compression and compression-transfer are used for specific cases. Rotomoulding is specifically used for polyethylene and a few other powdered resins. Slush moulding is broadly used for automotive dashboards. Generally ... [Pg.23]

Slush moulding used with thermoplastics in powder form for the fabrication of automotive dashboards ... [Pg.24]

Interior trims, dashboards, instrument panel inserts, pillar trims, consoles, airbag system parts, door and quarter-panel trims, lift-gate trims. .. [Pg.87]

Instrument panels and associated mouldings, dashboards, interior door panels and pockets, sun visors, security covers, headlining, floor coverings, floor mats, arm rests, seat coverings. .. [Pg.88]

Interior cladding, dashboards, instrument panel retainers, knee bolsters, glove box doors, steering column covers, defroster/demister grilles, speaker grilles. .. [Pg.90]

Some parts such as dashboards are an inextricable combination of various subparts of different materials making it impossible to dismantle. The choice of compatible materials is advised to allow recycling. For example, a part can be made out of several olefin subparts ... [Pg.95]

A dashboard is a complex part with several subparts of very different functionalities ... [Pg.96]

TPO applications are in automotive bumpers and dashboards because of their higher toughness than conventional polypropylene copolymers. [Pg.657]

Slush moulding is broadly used for automotive dashboards. [Pg.717]

This process is used for the production of dashboards and skins for consoles, door trims and glove boxes for the automotive industry. [Pg.726]

Mass production parts bumpers, soundproofing shields, cross-pieces, inserts for dashboards, seat frames, containers, welding helmets, ventilator housings, base of lawn-mowers, taping of pipes, pipelines, tanks, long fibre reinforced injected parts. [Pg.775]

Dashboard carriers low emission and fogging values are achievable with HPGF. [Pg.841]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...