Cracking catalysts acidity

The catalytic activity of amorphous silica-alumina ([Si—Al]) in reactions via carbonium ions is due to the existence of Bronsted acid sites on their surface. Consequently, amorphous [Si-Al] acid catalysts provide acid sites and transport to the active sites easily. As a result, amorphous [Si-Al] acid catalysts have been widely operated as cracking catalysts. Acid zeolites have been successfully applied as cracking catalysts. However, in some industrial applications of acid catalysts, for example, in the cracking of hydrocarbons of high molecular weight, zeolites are not useful, since... 

Still another type of adsorption system is that in which either a proton transfer occurs between the adsorbent site and the adsorbate or a Lewis acid-base type of reaction occurs. An important group of solids having acid sites is that of the various silica-aluminas, widely used as cracking catalysts. The sites center on surface aluminum ions but could be either proton donor (Brpnsted acid) or Lewis acid in type. The type of site can be distinguished by infrared spectroscopy, since an adsorbed base, such as ammonia or pyridine, should be either in the ammonium or pyridinium ion form or in coordinated form. The type of data obtainable is illustrated in Fig. XVIII-20, which shows a portion of the infrared spectrum of pyridine adsorbed on a Mo(IV)-Al203 catalyst. In the presence of some surface water both Lewis and Brpnsted types of adsorbed pyridine are seen, as marked in the figure. Thus the features at 1450 and 1620 cm are attributed to pyridine bound to Lewis acid sites, while those at 1540... 

Zeolites as cracking catalysts are characterized hy higher activity and better selectivity toward middle distillates than amorphous silica-alumina catalysts. This is attrihuted to a greater acid sites density and a higher adsorption power for the reactants on the catalyst surface. 

The first commercial fluidized cracking catalyst was acid-treated natural clay. Later, synthetic. silica-alumina materials containing 10 lo... 

This review will endeavor to outline some of the advantages of Raman Spectroscopy and so stimulate interest among workers in the field of surface chemistry to utilize Raman Spectroscopy in the study of surface phenomena. Up to the present time, most of the work has been directed to adsorption on oxide surfaces such as silicas and aluminas. An examination of the spectrum of a molecule adsorbed on such a surface may reveal information as to whether the molecule is physically or chemically adsorbed and whether the adsorption site is a Lewis acid site (an electron deficient site which can accept electrons from the adsorbate molecule) or a Bronsted acid site (a site which can donate a proton to an adsorbate molecule). A specific example of a surface having both Lewis and Bronsted acid sites is provided by silica-aluminas which are used as cracking catalysts. 

A mixture of monolauryl phosphate sodium salt and triethylamine in H20 was treated with glycidol at 80°C for 8 h to give 98% lauryl 2,3-dihydro-xypropyl phosphate sodium salt [304]. Dyeing aids for polyester fibers exist of triethanolamine salts of ethoxylated phenol-styrene adduct phosphate esters [294], Fatty ethanolamide phosphate surfactant are obtained from the reaction of fatty alcohols and fatty ethanolamides with phosphorus pentoxide and neutralization of the product [295]. A double bond in the alkyl group of phosphoric acid esters alter the properties of the molecule. Diethylethanolamine salt of oleyl phosphate is effectively used as a dispersant for antimony oxide in a mixture of xylene-type solvent and water. The composition is useful as an additive for preventing functional deterioration of fluid catalytic cracking catalysts for heavy petroleum fractions. When it was allowed to stand at room temperature for 1 month it shows almost no precipitation [241]. 

The desulfurization process reported by the authors was a hybrid process, with a biooxidation step followed by a FCC step. The desulfurization apparently occurs in the second step. Thus, the process seems of no value, since it does not remove sulfur prior to the FCC step, but only oxidizes it to sulfoxides, sulfones, or sulfonic acids. The benefit of such an approach is not clearly outlined. The benefit of sulfur conversion can be realized only after its removal, and not via a partial oxidation. Most of the hydrotreatment is carried out prior to the FCC units, partially due to the detrimental effect that sulfur compounds exert on the cracking catalyst. It is widely accepted that the presence of sulfur, during the regeneration stage of the FCC units, causes catalyst deactivation associated with zeolite decay. In general terms, the subject matter of this document has apparent drawbacks. 

The first cracking catalysts were acid-leached montmorillonite clays. The acid leach was to remove various metal impurities, principally iron, copper, and nickel, that could exert adverse effects on the cracking performance of a catalyst. The catalysts were first used in fixed- and moving-bed reactor systems in the form of shaped pellets. Later, with the development of the fluid catalytic cracking process, clay catalysts were made in the form of a ground, sized powder. Clay catalysts are relatively inexpensive and have been used extensively for many years. 

During the period 1940-1962, the cracking catalysts used most widely commercially were the aforementioned acid-leached clays and silica-alumina. The latter was made in two versions low alumina (about 13% AI2O3) and high alumina (about 25% AI2O3) contents. High-alumina-content catalysts showed a higher equilibrium activity level and surface area. 

Commercially used cracking catalysts are insulator catalysts possessing strong protonic (acidic) properties. They function as catalyst by altering the cracking... 

The hydrogen sulfide and ammonia can be removed by amine extraction and acid washes respectively. Hydrotreating also removes metals from the feed that would otherwise poison the reforming and cracking catalysts. 

Kaolinite is the main constituent in china clay used to make porcelain. The layers are largely held together by van der Waals forces. Bentonite is used in cosmetics, as a filler for soaps, and as a plasticizer, and it is used in drilling-muds as a suspension stabilizer. Bentonite and kaolinite clays are used, after treatment with sulfuric acid to create acidic surface sites, as petroleum cracking catalysts. Asbestos also has a layered structure (Section 12.13). 

Prior to 1938, gasoline was obtained from thermal-cracking plants then the Houdry fixed-bed catalytic cracking process led to the development of a fluidized-bed process by Standard Oil for the catalytic production of motor fuels (4-8). Acid-treated clays of the montmorilIonite type were the first fluid-cracking catalysts widely employed by the industry. However, the ever greater demand for aviation fuels during the 1939-1945 period prompted the search for more active and selective catalysts. Research on novel catalyst... 

Under FCCU operating conditions, almost 100% of the metal contaminants in the feed (such as nickel, vanadium, iron and copper porphyrins) are decomposed and deposited on the catalyst (2). The most harmful of these contaminants are vanadium and nickel. The deleterious effect of the deposited vanadium on catalyst performance and the manner in which vanadium is deposited on the cracking catalyst differ from those of nickel. The effect of vanadium on the catalyst performance is primarily a decrease in catalyst activity while the major effect of nickel is a selectivity change reflected in increased coke and gas yields (3). Recent laboratory studies (3-6) show that nickel distributes homogeneously over the catalyst surface while vanadium preferentially deposits on and reacts destructively with the zeolite. A mechanism for vanadium poisoning involving volatile vanadic acid as the... 

Another heteroatom in the feed which affects performance and product quality is nitrogen. Basic nitrogen in the feed tends to lower cracking activity by adsorbing onto the acid sites of the surface of the cracking catalyst. The work of Wu and Schaffer (5), showed that not all nitrogen compounds were equally harmful. They... 

Faced with the need of obtaining more transportation fuels from a barrel of crude, Ashland developed the Reduced Crude Conversion Process (RCC ). To support this development, a residuum or reduced crude cracking catalyst was developed and over 1,000 tons were produced and employed in commercial operation. The catalyst possessed a large pore volume, dual pore structure, an Ultrastable Y zeolite with an acidic matrix equal in acidity to the acidity of the zeolite, and was partially treated with rare earth to enhance cracking activity and to resist vanadium poisoning. 

---