Butyl acetate alcohol

Polyvinyl chloride Tetrahydrofuran Hydrocarbons, butyl acetate alcohols... 

Polyvinylidene chloride Tetrahydrofliran, dioxane ketones, butyl acetate Alcohols, hydrocarbons... 

Hydrolysis (or saponification) of n-butyl acetate. Boil 4-5 g. of n-butyl acetate (Section 111,95) with 50 ml. of 10 per cent, sodium hydroxide solution under reflux until the odour of the ester can no longer be detected (about 1 hour). Set the condenser for downward distiUation and coUect the first 10 ml. of distillate. Saturate it with potassium carbonate, aUow to stand for 5 minutes, and withdraw all the Uquid into a small pipette or dropper pipette. AUow the lower layer of carbonate solution to run slowly into a test-tube, and place the upper layer into a small test-tube or weighing bottle. Dry the alcohol with about one quarter of its buUr of anhydrous potassium carbonate. Remove the alcohol with a dropper pipette and divide it into two parts use one portion for the determination of the b.p. by the Siwoloboff method (Section 11,12) and convert the other portion into the 3 5-dinitrobenzoate (Section III, 27) and determine the m.p. 

Mercaptals, CH2CH(SR)2, are formed in a like manner by the addition of mercaptans. The formation of acetals by noncatalytic vapor-phase reactions of acetaldehyde and various alcohols at 35°C has been reported (67). Butadiene [106-99-0] can be made by the reaction of acetaldehyde and ethyl alcohol at temperatures above 300°C over a tantala—siUca catalyst (68). Aldol and crotonaldehyde are beheved to be intermediates. Butyl acetate [123-86-4] has been prepared by the catalytic reaction of acetaldehyde with 1-butanol [71-36-3] at 300°C (69). 

Ketones and esters are required for C-type inks. Types of esters are ethyl acetate, isopropyl acetate, normal propyl acetate, and butyl acetate. From the ketone class, acetone or methyl ethyl ketone (MEK) can be used. The usual solvent for D-type inks are mixtures of an alcohol, such as ethyl alcohol or isopropyl alcohol, with either aUphatic or aromatic hydrocarbons. Commonly used mixtures are 50/50 blends by volume of alcohol and aUphatic hydrocarbon. 

Butanol is used as a direct solvent ia paints and other surface coatings. It acts synergisticaHy with butyl acetate as a latent solvent system for nitrocellulose lacquers and thinners to give a solvent system stronger than either solvent alone. Other direct solvent appHcations for -butyl alcohol are ia the formulation of pharmaceuticals, waxes, and resias. 

Butyl acetate [123-86-4], one of the more important derivatives of -butyl alcohol produced commercially, is employed as a solvent ia rapid dryiag paints and coatings. In some instances, butyl acetate, has replaced ethoxyethyl acetate [111-15-9] due to the latter s reported toxicity and... 

Esters of medium volatility are capable of removing the water formed by distillation. Examples are propyl, butyl, and amyl formates, ethyl, propyl, butyl, and amyl acetates, and the methyl and ethyl esters of propionic, butyric, and valeric acids. In some cases, ternary azeotropic mixtures of alcohol, ester, and water are formed. This group is capable of further subdivision with ethyl acetate, all of the ester is removed as a vapor mixture with alcohol and part of the water, while the balance of the water accumulates in the system. With butyl acetate, on the other hand, all of the water formed is removed overhead with part of the ester and alcohol, and the balance of the ester accumulates as a high boiler in the system. 

Ethanol can also be obtained by the reaction of methanol with synthesis gas at 185°C and under pressure (6.9—20.7 MPa or 68—204 atm) in the presence of a cobalt octacarbonyl catalyst (177). However, although ethanol was the primary product, methyl formate, methyl, propyl and butyl acetates, propyl and butyl alcohols, and methane were all present in the product. 

Acetone with benzene, butyl acetate, butyl alcohol, carbon tetrachloride, chloroform, cyclohexane, ethanol, ethyl acetate, methyl acetate, acetonitrile, petroleum ether or water. 

Propargyl alcohol (2-propyn-l-ol) [107-19-7] M 56.1, b 54 /57mm, 113.6 /760mm, d 0.947, n 1.432. Commercial material contains a stabiliser. An aqueous soln of propargyl alcohol can be concentrated by azeotropic distn with butanol or butyl acetate. Dried with K2CO3 and distd under reduced pressure, in the presence of about 1% succinic acid, through a glass helices-packed column. 

Nitro-filter cloths are composed of cellulose nitrate, which is an ester of cellulose. Any chemical compound that will saponify the ester will destroy the cloth. Caustic soda or potash in strengths of 2% at 70° C or over alkali sulfides, polysulfides and sulfohydrates or mixtures of ethyl alcohol and ether, ethyl, amyl and butyl acetates, pyridine, ferrous sulfates, and other reducing agents are detrimental to the cloth. 

Butter Yellow, 29 Butyl acetates, 29 Butyl acid phosphate, 29 Butyl acrylate, 29 Butyl alcohols, 29 Butyl amines, 29 Butylate, 30... 

Acetaldehyde, acetone, isopropyl alcohol, ethyl acetate, methyl isobutyl ketone, toluene, butyl acetate, isobutyl alcohol, and acetic acid... 

The reaction scheme is rather complex also in the case of the oxidation of o-xylene (41a, 87a), of the oxidative dehydrogenation of n-butenes over bismuth-molybdenum catalyst (87b), or of ethylbenzene on aluminum oxide catalysts (87c), in the hydrogenolysis of glucose (87d) over Ni-kieselguhr or of n-butane on a nickel on silica catalyst (87e), and in the hydrogenation of succinimide in isopropyl alcohol on Ni-Al2Oa catalyst (87f) or of acetophenone on Rh-Al203 catalyst (87g). Decomposition of n-and sec-butyl acetates on synthetic zeolites accompanied by the isomerization of the formed butenes has also been the subject of a kinetic study (87h). 

GC assay of the organic layer showed no EIN(TMS)2 remaining after 15 min of stirring (GC conditions Restek RTX-1 column (30 m x 0.53 mm, 1 m film thickness), 2.53 mL/min, initial temperature 50°C, final temperature 300°C, rate 20 deg/min, injection temperature 200°C, detector temperature 350°C, injection volume 1 pL, inject sample neat retention times fert-butyl alcohol 1.4 min, THF 1.7 min, heptane 2.1 min, HN(TMS)2 2.6 min, ethylbenzene (present in commercial LHS) 3.1 min, te/ t-butyl acetate 4.0 min). Volume percents were determined based on standard solution counts. 

The Claisen condensation of t-butyl acetate with a methyl ester is a general route for the preparation of complex P-ketoesters.4 The reaction requires an excess of the enolate of t-butyl acetate to rapidly deprotonate the product and prevent tertiary alcohol formation. Some workers have also used excess LDA or t-butoxide for this purpose. 

Finally, reaction of primary, secondary, or tertiary alcohols 11 with Me3SiCl 14 in the presence of equivalent amounts of DMSO leads via 789 and 790 to the chloro compounds 791 [13]. n-Pentanol, benzyl alcohol, yS-phenylefhanol or tert-butanol are readily converted, after 10 min reaction time, into their chloro compounds, in 89-95% yield, yet cyclohexanol affords after reflux for 4 h cyclohexyl chloride 784 in only 6% yield [13] (Scheme 6.5). 1,4-Butanediol is cyclized to tetrahydrofuran (THF) [13a], whereas other primary alcohols are converted in 90-95% yield into formaldehyde acetals on heating with TCS 14 and DMSO in benzene [13b] (cf also the preparation of formaldehyde di(n-butyl)acetal 1280 in Section 8.2.1). 

DMSO or other sulfoxides react with trimethylchlorosilanes (TCS) 14 or trimefhylsilyl bromide 16, via 789, to give the Sila-Pummerer product 1275. Rearrangement of 789 and further reaction with TCS 14 affords, with elimination of HMDSO 7 and via 1276 and 1277, methanesulfenyl chloride 1278, which is also accessible by chlorination of dimethyldisulfide, by treatment of DMSO with Me2SiCl2 48, with formation of silicon oil 56, or by reaction of DMSO with oxalyl chloride, whereupon CO and CO2 is evolved (cf also Section 8.2.2). On heating equimolar amounts of primary or secondary alcohols with DMSO and TCS 14 in benzene, formaldehyde acetals are formed in 76-96% yield [67]. Thus reaction of -butanol with DMSO and TCS 14 gives, via intermediate 1275 and the mixed acetal 1279, formaldehyde di-n-butyl acetal 1280 in 81% yield and methyl mercaptan (Scheme 8.26). Most importantly, use of DMSO-Dg furnishes acetals in which the 0,0 -methylene group is deuter-ated. Benzyl alcohol, however, affords, under these reaction conditions, 93% diben-zyl ether 1817 and no acetal [67]. 

Acetic acid n-Butyl alcohol n Butyl acetate... 

---