Injectate temperature

High temperature steam (qv) is also used for recovery of viscous cmde oils (28). Heat from the steam thins the oil, reducing viscosity and increasing mobihty. The mobilized oil is produced at offset production wells. In heavy oil fields, water flooding is often omitted and steam injection begun immediately after primary production. Steam injection temperature is typically 175—230°C in California oil fields. Injection temperature can reach 300°C in Canadian and Venezuelan EOR projects. 

Cool on-column injection is used for trace analysis. Ah. of the sample is introduced without vaporization by inserting the needle of the syringe at a place where the column has been previously stripped of hquid phase. The injection temperature must be at or below the boiling point of the solvent carrying the sample. Injection must be rapid and no more than a very few, usuahy no more than two, microliters may be injected. Cool on-column injection is the most accurate and reproducible injection technique for capihary chromatography, but it is the most difficult to automate. 

GC assay of the organic layer showed no EIN(TMS)2 remaining after 15 min of stirring (GC conditions Restek RTX-1 column (30 m x 0.53 mm, 1 m film thickness), 2.53 mL/min, initial temperature 50°C, final temperature 300°C, rate 20 deg/min, injection temperature 200°C, detector temperature 350°C, injection volume 1 pL, inject sample neat retention times fert-butyl alcohol 1.4 min, THF 1.7 min, heptane 2.1 min, HN(TMS)2 2.6 min, ethylbenzene (present in commercial LHS) 3.1 min, te/ t-butyl acetate 4.0 min). Volume percents were determined based on standard solution counts. 

Column temperature Injection temperature Detector Temperature Gas flow rates... 

Hot splitless WCOT 0.5 ppm (FID) without preconcentration Lower injection temperature than split Trace analysis Handles dirty samples Automation Flash vaporisation Optimisation required (splitless time, oven temperature, solvent) Limited number of solvents ( solvent effect ) Thermal degradation possible Discrimination possible Poor direct quantification Unsuitable for very polar substances... 

Bottom Hole Injection Temperature Average injection rate ... 

Guo et al. [53] developed a gas chromatographic method for the analysis of miconazole nitrate in creams and injections. The conditions were flame ionization detector, stationary phase of 5% SE 30 support of Chromosorb W (AS-DMCS, 80—100 mesh) packed column 3 m x 3 mm column temperature 275 °C injection temperature 290 °C and diisooctyl sebacate and internal standard. The average recoveries for creams and injections were 97.7 and 101.4%, respectively. The relative standard deviations were 2.2 and 1.3%, respectively. 

Obtain chromatograms of the three standards and also the pure gasoline (0% added). Give the column plenty of time to clear between injections—temperature programming may be useful. 

Gas chromatographic analysis indicates that this consists of 97-99% of citronellol and 1-3% of dihydrocitronellol column, SHIMADZU HiCap-CBP20, 25 m x 0.2-mm fused silica column temperature, 140°C injection temperature 160°C helium pressure as carrier gas, 1.0 kg/cm2 tR of geraniol, citronellol, and dihydrocitronellol are 16.2,13.7, and 8.6 min, respectively. 

A continuous flow stirred reactor operates off the decomposition of gaseous ethylene oxide fuel. If the fuel injection temperature is 300 K, the volume of the reactor is 1500 cm3, and the operating pressure is 20 atm, calculate the maximum rate of heat evolution possible in the reactor. Assume that the ethylene oxide follows homogeneous first-order reaction kinetics and that values of the reaction rate constant k are... 

The operating conditions were injection temperature 150°C, detector temperature 250°C, carrier nitrogerr. Sample sizes were used 1.0 pi and manual type of injectioa... 

All aldehydes used in the experiment were freshly distilled or washed with aqueous NaHC03 solution to minimize the amount of free acid. Chiral HPLC was performed using a chiral OJ-H column (0.46 cm x 25 cm, Daicel industries) with a water 717 auto sampler and a UV-vis detector (254 nm). The eluting solvent used was different ratios of hexane and 2-propanol. Chiral gas chromatography analysis was performed in a Shimadzu auto sampler with cyclodextrins columns as chiral stationary phase (fused-silica capillary column, 30 m X 0.25 mm x 0.25 gm thickness, /3-Dex-120 and /3-Dex-325 from Supelco, USA) using He as a carrier gas (detector temperature 230 °C and injection temperature 220 °C). 

Gas chromatographic data was obtained on a Tracor Model 220 gas chromatograph equipped with a Varian Model 8000 autosampler. The analysis column was a 1.7 m "U column, 4 mm id, filled with 3% SP-2250 packing (Supelco, Inc., Bellefonte, PA) held at 200 C. The injection temperature was 250 and the nitrogen carrier gas flow rate was 60 mL/min. The detector temperatures were 350 for electron capture and 190 for flame photometric. Detector signals were processed by a Varian Vista 401 which gave retention times and peak areas. 

Figure 10.35 The effect of hydraulic pressure on injectate temperature and specific rate. The data are for a 125 mm diameter screw and an intensification factor of 10 for a molding machine running a HIPS resin at a screw speed of 100 rpm...

Gas chromatographic analysis (10% Carbowax 20 M on 80-100 mesh Chromosorb W, 2.5 m x 2 mm, column temperature 180°C, injection temperature 230°C, flow rate 10 mL/min, retention time 10 min) of the corresponding dimethyl ester, formed with ethereal diazomethane, indicated a purity of greater than 99%. 

Gas chromatographic analysis of the product (Hewlett-Packard fused silica, cross-linked methyl silicone capillary column, 25 m x 20 mm, column temperature 100-270°C, injection temperature 250°C) shows that the product is over 99% chemically and isomerically pure, (Z,E)-l-Phenyl-l,3-octadiene shows the following spectral properties IR (neat) cm 1640, 1595, 1490, 985 ... 

The injection temperature can be a signiflcant issne for thermally unstable samples or where samples are stored for hours in an antosampler prior to injection. For this reason, most manufacturers sell autosamplers with optional thermostated sample compartments. This can be done either by placing the sample tray in an air bath oven or by a condnctive temperature control of the sample rack. The need to keep samples cool prior to injection when conpled with elevated temperature separation increases the complexity of the flow system reqnired. For such application, a separate mobile phase pre-heater with a low volnme placed between the injector and the column is a good choice. Alternatively, the injector valve wonld need to be monnted ontside the antosampler or in the column oven to insure preheating of the mobile phase before the colnmn. 

Toxicity CBC with differential periodically particularly platelets vital signs in patients with a history of hypersensitivity to any medication (first injection) temperature periodically (infection)... 

---