Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Antimony water

It behoves us therefore by this our water to attenuate, alter and soften the perfect bodies, to wit sol and luna, that so they may be mixed other perfect bodies. From whence, if we had no other benefit bu this our antimonial water, than that it rendered bodies soft, more subtile, and fluid, according... [Pg.4]

Antimony peniachloride, SbCls. M.p. TC, b.p. 79 C (Sb or SbCIa plus CI2). Readily hydrolysed by water, forms complexes, e.g. [SbClft]". Mixed antimony(III)/(V) complexes occur as salts M2SbCl6. SbCls is used extensively as a chlorinating agent. [Pg.39]

Antimony Ill) fluoride is a readily hydrolysable solid which finds use as a fluorinaling agent. Antimony(lll) chloride is a soft solid, m.p. 347 K. It dissolves in water, but on dilution partial hydrolysis occurs and antimony chloride oxide SbOCl is precipitated ... [Pg.253]

The gas is washed with water to remove any hydrogen chloride. Since iron(II) sulphide is a non-stoichiometric compound and always contains some free iron, the hydrogen sulphide always contains some hydrogen, liberated by the action of the iron on the acid. A sample of hydrogen sulphide of better purity can be obtained if antimony(III) sulphide, (stibnite) SbjSj, is warmed with concentrated hydrochloric acid ... [Pg.282]

Add 5 g. of potassium hydrogen tartrate and 5 g. of antimony trioxide (each being finely powdered) to 30 ml. of water contained in a small flask, and boil the mixture under a reflux water-condenser for 15 minutes. Then filter hot, using a Buchner funnel and flask which have been preheated by the filtration of some boiling distilled water. Pour the clear filtrate into a beaker and allow to cool. Potassium antimonyl tartrate separates as colourless crystals. Filter, drain and dry. Yield, 5 g. The product can be recrystallised from hot water, but this is usually not necessary. [Pg.115]

It is recommended that the eompound be fused with a mixture of sodium carbonate (2 parts) and sodium peroxide (1 part) as in the test for Plvoaphoms. Extract the fused mass with water, filter, and acidify with dilute hydrochloric acid. Pass hydrogen sulphide through the hot solution arsenic is precipitated as yellow arsenic sulphide. If antimony is present, it will be precipitated as orange antimony trisulphide. [Pg.1043]

Sellaite, see Magnesium fluoride Senarmontite, see Antimony(III) oxide Siderite, see Iron(II) carbonate Siderotil, see Iron(II) sulfate 5-water Silica, see Silicon dioxide Silicotungstic acid, see Silicon oxide—tungsten oxide—water (1/12/26)... [Pg.275]

Valentinite, see Antimony(III) oxide Verdigris, see Copper acetate hydrate Vermillion, see Mercury(II) sulflde Villiaumite, see Sodium fluoride Vitamin B3, see Calcium (+)pantothenate Washing soda, see Sodium carbonate 10-water Whitlockite, see Calcium phosphate Willemite, see Zinc silicate(4—)... [Pg.275]

Antimony Oxide as a Primary Flame Retardant. Antimony oxide behaves as a condensed-phase flame retardant in cellulosic materials (2). It can be appHed by impregnating a fabric with a soluble antimony salt followed by a second treatment that precipitates antimony oxide in the fibers. When the treated fabric is exposed to a flame, the oxide reacts with the hydroxyl groups of the cellulose (qv) causing them to decompose endothermically. The decomposition products, water and char, cool the flame reactions while slowing the production and volatilization of flammable decomposition products (see Flaa retardants for textiles). [Pg.455]

Sodium Antimonate. Sodium antimonate [15593-75-6] Na SbO, another antimony synergist of commercial importance, has an antimony content of 61—63 wt % and a bulk density of 39.4—46.4 kg/m. Properties are given in Table 2. It is made by oxidizing antimony trioxide using sodium nitrate and caustic. It is a white powder and has a pH of around 9—11 when dissolved in water. [Pg.455]

Ethylene glycol esterification of BHET is driven to completion by heating and removal of the water formed. PET is also formed using the same chemistry starting with dimethyl terephthalate [120-61-6] and ethylene glycol to form BHET also using an antimony oxide catalyst. [Pg.357]

Commercial Stabilizers. The performance of the antimony stabilizers is significantly enhanced by adding polyhydroxybenzene compounds, eg, catechol, to the PVC (36). In commercial practice, about 5—10% catechol is formulated with the antimony mercaptide stabilizer products. The antimony mercaptides are normally prepared by heating antimony oxide with the appropriate mercaptan, normally isooctyl thioglycolate, under conditions to remove water. [Pg.552]

Health and Safety Aspects. The U.S. EPA has significantly reduced the aHowed levels of antimony compounds in drinking water causing a toxicity cloud over the viabHity of this class of stabilizers. Presently, antimony products are no longer aHowed for use as potable water pipe stabilizers pending completion of NSE International s review (28). Eor these reasons, the future of this stabilizer technology appears limited. [Pg.552]

Particular drawbacks of using alkylsiHcon and alkyltin haHdes with AlCl for the cationic polymerization of terpenes are low yields and the fact that they require rigorously dried feeds (<50 ppm H2O) to be effective. Increased water content results in lower yields and lower softening points (85). Catalyst systems comprised of AlCl with antimony haHdes in the presence or absence of a lower alkyl, alkenyl, or aralkyl haHde are particularly effective in systems containing up to 300 ppm H2O (89,90). Use of 2—12 wt % of a system composed of 2—3 parts AlCl, 0.7—0.9 parts SbCl, and 0—0.2 parts of an organic... [Pg.356]

For the production of tartar emetic (antimony potassium tartrate [28300-74-5]), potassium bitartrate [868-14 ] and antimony oxide, Sb202, are added simultaneously to water in a stainless-steel reactor. The reaction mixture is diluted, filtered, and collected in jacketed granulators where crystallization takes place after cooling. Centrihiging, washing, and drying complete the process. [Pg.526]

Automobile battery grids employ about 1—3 wt % antimony—lead alloys. Hybrid batteries use low (1.6—2.5 wt %) alloys for the positive grids and nonantimony alloys for the negative grids to give reduced or no water loss. The posts and straps of virtually all lead—acid batteries are made of alloys containing about 3 wt % antimony. [Pg.56]

After firing, the powder is washed in water typically with a small amount of complexing agent such as ethylenediarninetetraacetic acid (EDTA), sodium EDTA, or a weak acid such as citric acid to remove the excess chloride, volatile antimony oxychlorides which have recondensed on the phosphor during cooling, and manganese compounds which are not incorporated in the halophosphate lattice. The powder is then ready for suspension. [Pg.288]

Rubidium metal alloys with the other alkaU metals, the alkaline-earth metals, antimony, bismuth, gold, and mercury. Rubidium forms double haUde salts with antimony, bismuth, cadmium, cobalt, copper, iron, lead, manganese, mercury, nickel, thorium, and 2iac. These complexes are generally water iasoluble and not hygroscopic. The soluble mbidium compounds are acetate, bromide, carbonate, chloride, chromate, fluoride, formate, hydroxide, iodide. [Pg.278]

In a batch process (176), a glass-lined jacketed iron vessel is charged with either sulfur monochloride or sulfur dichloride and about 1% of antimony trichloride as a catalyst. Chlorine is introduced into the reactor near the bottom. Liquid oleum is added to the reactor at such a rate that the temperature of the reaction mass is held at ca 25°C by the use of cooling water in the jacket. [Pg.141]

Generally, the concentration of antimony in the air varies from 1 x 10 mg/m to 170 x 10 mg/m and can be as high as 1000 x 10 mg/m neat antimony processing faciHties (33). Because of the stabiHty of antimony in aqueous systems, the concentration of dissolved antimony in fivers is very small (about 5 ppb antimony). Also, despite the fact that antimony is in the solder used in water pipes, it does not appear to dissolve in the drinking water. [Pg.199]

Antimony trioxide is insoluble in organic solvents and only very slightly soluble in water. The compound does form a number of hydrates of indefinite composition which are related to the hypothetical antimonic(III) acid (antimonous acid). In acidic solution antimony trioxide dissolves to form a complex series of polyantimonic(III) acids freshly precipitated antimony trioxide dissolves in strongly basic solutions with the formation of the antimonate ion [29872-00-2] Sb(OH) , as well as more complex species. Addition of suitable metal ions to these solutions permits formation of salts. Other derivatives are made by heating antimony trioxide with appropriate metal oxides or carbonates. [Pg.202]


See other pages where Antimony water is mentioned: [Pg.275]    [Pg.41]    [Pg.275]    [Pg.41]    [Pg.38]    [Pg.39]    [Pg.39]    [Pg.452]    [Pg.454]    [Pg.455]    [Pg.457]    [Pg.487]    [Pg.150]    [Pg.150]    [Pg.150]    [Pg.307]    [Pg.159]    [Pg.545]    [Pg.357]    [Pg.80]    [Pg.56]    [Pg.56]    [Pg.57]    [Pg.57]    [Pg.332]    [Pg.506]    [Pg.6]    [Pg.56]    [Pg.196]    [Pg.198]    [Pg.202]    [Pg.203]   
See also in sourсe #XX -- [ Pg.661 ]




SEARCH



Antimony in waters

Drinking water containing antimony

© 2024 chempedia.info