Ammonia caprolactam

ISOCIANATO de METILO (Spanish) (624-83-9) Forms explosive mixture with air (flash point 0°F/- 18°C). Reacts slowly with water violently with warm water or steam, forming carbon dioxide and heat. Decomposes above 100°F/38 C. Violent reaction with acetaldehyde, amines, alcohols, acids, alkalis, strong oxidizers. Unless inhibited, can produce unstable peroxides contact with iron, tin, copper, or salts of these elements, or with certain catalysts such as triphenylarsenic oxide, triethylphosphine, or tributyltin oxide, or elevated temperatures may cause polymerization. Incompatible with glycols, amides, ammonia, caprolactam. Attacks some plastics, rubber, or coatings. The uninhibited monomer vapor may block vents and confined spaces by forming a solid polymer material. 

An additional mole of ammonium sulfate per mole of final lactam is generated duting the manufacture of hydroxylamine sulfate [10039-54-0] via the Raschig process, which converts ammonia, air, water, carbon dioxide, and sulfur dioxide to the hydroxylamine salt. Thus, a minimum of two moles of ammonium sulfate is produced per mole of lactam, but commercial processes can approach twice that amount. The DSM/Stamicarbon HPO process, which uses hydroxylamine phosphate [19098-16-9] ia a recycled phosphate buffer, can reduce the amount to less than two moles per mole of lactam. Ammonium sulfate is sold as a fertilizer. However, because H2SO4 is released and acidifies the soil as the salt decomposes, it is alow grade fertilizer, and contributes only marginally to the economics of the process (145,146) (see Caprolactam). 

Ammonia is consumed in the manufacture of ammonium phosphates and ammonium sulfate by reaction with phosphoric acid and sulfuric acid, respectively. The phosphates may contain ortho- and polyphosphate values. Ammonium sulfate is also a by-product from other ammonia-using industries such as caprolactam (qv) and hydrogen cyanide (see Cyanides). 

Ammonia is used in the fibers and plastic industry as the source of nitrogen for the production of caprolactam, the monomer for nylon 6. Oxidation of propylene with ammonia gives acrylonitrile (qv), used for the manufacture of acryHc fibers, resins, and elastomers. Hexamethylenetetramine (HMTA), produced from ammonia and formaldehyde, is used in the manufacture of phenoHc thermosetting resins (see Phenolic resins). Toluene 2,4-cHisocyanate (TDI), employed in the production of polyurethane foam, indirectly consumes ammonia because nitric acid is a raw material in the TDI manufacturing process (see Amines Isocyanates). Urea, which is produced from ammonia, is used in the manufacture of urea—formaldehyde synthetic resins (see Amino resins). Melamine is produced by polymerization of dicyanodiamine and high pressure, high temperature pyrolysis of urea, both in the presence of ammonia (see Cyanamides). 

Caprolactam [105-60-2] (2-oxohexamethyleiiiiriiQe, liexaliydro-2J -a2epin-2-one) is one of the most widely used chemical intermediates. However, almost all of the aimual production of 3.0 x 10 t is consumed as the monomer for nylon-6 fibers and plastics (see Fibers survey Polyamides, plastics). Cyclohexanone, which is the most common organic precursor of caprolactam, is made from benzene by either phenol hydrogenation or cyclohexane oxidation (see Cyclohexanoland cyclohexanone). Reaction with ammonia-derived hydroxjlamine forms cyclohexanone oxime, which undergoes molecular rearrangement to the seven-membered ring S-caprolactam. 

Cyclohexanone oxime is converted quantitatively to caprolactam by Beckmann rearrangement in the presence of oleum, which is of sufficient strength to consume the several percent water in the molten oxime. The reaction mass is neutralized with aqueous ammonia to a cmde caprolactam layer and a saturated solution of ammonium sulfate. Approximately 1.5 kg of the total 4.4 kg ammonium sulfate per kilogram of caprolactam is produced in this step. Purification is by multistage vacuum crystallization from aqueous solution in neatly quantitative yield. 

Hydroxylamine sulfate is produced by direct hydrogen reduction of nitric oxide over platinum catalyst in the presence of sulfuric acid. Only 0.9 kg ammonium sulfate is produced per kilogram of caprolactam, but at the expense of hydrogen consumption (11). A concentrated nitric oxide stream is obtained by catalytic oxidation of ammonia with oxygen. Steam is used as a diluent in order to avoid operating within the explosive limits for the system. The oxidation is followed by condensation of the steam. The net reaction is... 

The oxime is converted to caprolactam by Beckmann rearrangement neutralization with ammonia gives ca 1.8 kg ammonium sulfate per kilogram of caprolactam. Purification is by vacuum distillation. A no-sulfate, extraction process has been described, but incineration of the ammonium bisulfate recovers only sulfur values and it is not practiced commercially (14). 

Toray. The photonitrosation of cyclohexane or PNC process results in the direct conversion of cyclohexane to cyclohexanone oxime hydrochloride by reaction with nitrosyl chloride in the presence of uv light (15) (see Photochemical technology). Beckmann rearrangement of the cyclohexanone oxime hydrochloride in oleum results in the evolution of HCl, which is recycled to form NOCl by reaction with nitrosylsulfuric acid. The latter is produced by conventional absorption of NO from ammonia oxidation in oleum. Neutralization of the rearrangement mass with ammonia yields 1.7 kg ammonium sulfate per kilogram of caprolactam. Purification is by vacuum distillation. The novel chemistry is as follows ... 

Snia Viscosa. Catalytic air oxidation of toluene gives benzoic acid (qv) in ca 90% yield. The benzoic acid is hydrogenated over a palladium catalyst to cyclohexanecarboxyhc acid [98-89-5]. This is converted directiy to cmde caprolactam by nitrosation with nitrosylsulfuric acid, which is produced by conventional absorption of NO in oleum. Normally, the reaction mass is neutralized with ammonia to form 4 kg ammonium sulfate per kilogram of caprolactam (16). In a no-sulfate version of the process, the reaction mass is diluted with water and is extracted with an alkylphenol solvent. The aqueous phase is decomposed by thermal means for recovery of sulfur dioxide, which is recycled (17). The basic process chemistry is as follows ... 

Until the mid-1950s the main raw material source for the European plastics industry was coal. On destructive distillation coal yields four products coal tar, coke, coal gas and ammonia. Coal tar was an important source of aromatic chemicals such as benzene, toluene, phenol, naphthalene and related products. From these materials other chemicals such as adipic acid, hexamethylenedia-mine, caprolactam and phthalic anhydride could be produced, leading to such important plastics as the phenolic resins, polystyrene and the nylons. 

The conversion of cyclohexanone to cyclohexanone oxime is brought about by the use of hydroxylamine sulphate. The sulphuric acid is neutralised with ammonia to ammonium sulphate and this is separated from the oxime. In the presence of oleum the oxime undergoes the process known as the Beckmann rearrangement to yield the crude caprolactam. After further neutralisation with ammonia the caprolactam and further ammonium sulphate are separated by solvent extraction (Figure 18.7). 

In one process the resulting solution is continuously withdrawn and cooled rapidly to below 75°C to prevent hydrolysis and then further cooled before being neutralised with ammonia. After phase separation, the oil phase is then treated with trichlorethylene to extract the caprolactam, which is then steam distilled. Pure caprolactam has a boiling point of 120°C at 10 mmHg pressure. In the above process 5.1 tons of ammonium sulphate are produced as a by-product per ton of caprolactam. 

Ammonium sulfate is produced as a caprolactam by-product from the petrochemical industry, as a coke by-product, and synthetically through reaction of ammonia with sulfuric acid. Only the third process is covered in our discussion. The reaction between anunonia and sulfuric acid produces an ammonium sulfate solution that is continuously circulated through an evaporator to thicken the solution and to produce ammonium sulfate crystals. The crystals are separated from the liquor in a centrifuge, and the liquor is returned to the evaporator. The crystals are fed either to a fluidized bed or to a rotary drum dryer and are screened before bagging or bulk loading. 

Ammonium sulphate is increasingly produced by reaction of synthetic ammonia with sulphuric acid from the process for production of caprolactam and via a method using gypsum. Ammonium sulphate is also used as a fertilizer. 

Ammonolysis is the preferred route currently in use at the DuPont Company for the depolymerization of nylon-6,6 carpet waste. McKinney13 has described the reaction of nylon-6,6 and nylon-6 mixtures with ammonia at temperatures in the range of 300-350°C at a pressure of about 68 atm in the presence of an ammonium phosphate catalyst to form a mixture of nylon-6,6 and nylon-6 monomers (HMD A, A A, and s-caprolactam) and adiponitrile, 5-cyanovaleramide, 6-aminocapronitrile, and 6-aminocaproamide. 

In die case of nylon-6,6 waste recycled by ammonolysis, nylon is treated with ammonia in die presence of a phosphate catalyst. Reaction occurs at 330°C and 7 MPa. Distillation of die reaction mixture produces ammonia which is recycled and three fractions containing (a) caprolactam, (b) HMDA and aminocaproni-trile, and (c) adiponitrile. Aminocapronitrile and adiponitrile are hydrogenated to yield pure HMDA, and die caprolactam is eidier converted to aminocapronitrile by further ammonolysis or distilled to produce pure caprolactam. The HMDA produced by this process is extremely pure (>99.8).1 The main impurities are aminomediylcyclopentylaniiiie and tetrahydroazepine, which are expected to be removed more effectively in the larger distillation columns employed in the larger plants. 

Table 4.1 gives the use profile for ammonia. It can be applied directly for fertilizer or made into other nitrogen-containing compounds used for fertilizer such as urea, ammonium nitrate, ammonium phosphate, ammonium sulfate, and nitric acid. Overall approximately 80% of ammonia has an end use as fertilizer. Explosives, a second important end use, made from ammonia are ammonium nitrate and, via nitric acid, the nitroglycerin used in dynamite. Chemical intermediates include acrylonitrile and caprolactam, which eventually go into fibers. 

---