Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

A-diamines

The leader of DuPont s effort was Wallace H Carothers who reasoned that he could reproduce the properties of silk by constructing a polymer chain held together as is silk by amide bonds The neces sary amide bonds were formed by heating a dicar boxylic acid with a diamine Hexanedioic acid adipic acid) and 1 6 hexanediamme hexamethylenedi-amine) react to give a salt that when heated gives a polyamide called nylon 66 The amide bonds form by a condensation reaction and nylon 66 is an example of a condensation polymer... [Pg.868]

As with polyesters, the amidation reaction of acid chlorides may be carried out in solution because of the enhanced reactivity of acid chlorides compared with carboxylic acids. A technique known as interfacial polymerization has been employed for the formation of polyamides and other step-growth polymers, including polyesters, polyurethanes, and polycarbonates. In this method the polymerization is carried out at the interface between two immiscible solutions, one of which contains one of the dissolved reactants, while the second monomer is dissolved in the other. Figure 5.7 shows a polyamide film forming at the interface between an aqueous solution of a diamine layered on a solution of a diacid chloride in an organic solvent. In this form interfacial polymerization is part of the standard repertoire of chemical demonstrations. It is sometimes called the nylon rope trick because of the filament of nylon produced by withdrawing the collapsed film. [Pg.307]

In the area of moleculady designed hot-melt adhesives, the most widely used resins are the polyamides (qv), formed upon reaction of a diamine and a dimer acid. Dimer acids (qv) are obtained from the Diels-Alder reaction of unsaturated fatty acids. Linoleic acid is an example. Judicious selection of diamine and diacid leads to a wide range of adhesive properties. Typical shear characteristics are in the range of thousands of kilopascals and are dependent upon temperature. Although hot-melt adhesives normally become quite brittle below the glass-transition temperature, these materials can often attain physical properties that approach those of a stmctural adhesive. These properties severely degrade as the material becomes Hquid above the melt temperature. [Pg.235]

To produce a spandex fiber by reaction spinning, a 1000—3500 molecular weight polyester or polyether glycol reacts with a diisocyanate at a molar ratio of about 1 2. The viscosity of this isocyanate-terrninated prepolymer may be adjusted by adding small amounts of an inert solvent, and then extmded into a coagulating bath that contains a diamine so that filament and polymer formation occur simultaneously. Reactions are completed as the filaments are cured and solvent evaporated on a belt dryer. After appHcation of a finish, the fibers are wound on tubes or bobbins and rewound if necessary to reduce interfiber cohesion. [Pg.307]

Polyetherimide synthesis has been achieved by reaction of a dianhydride containing an ether linkage with a diamine, reaction of a diamine containing an ether linkage with a dianhydride, or nucleophilic displacement of halo or nitro groups of a bisimide by bisphenol dianion (19,20). Such Pis exhibit good thermal stabiUty and melt processibiUty. [Pg.532]

Copolymers. There are two forms of copolymers, block and random. A nylon block copolymer can be made by combining two or more homopolymers in the melt, by reaction of a preformed polymer with diacid or diamine monomer by reaction of a complex molecule, eg, a bisoxazolone, with a diamine to produce a wide range of multiple amide sequences along the chain and by reaction of a diisocyanate and a dicarboxybc acid (193). In all routes, the composition of the melt is a function of temperature and more so of time. Two homopolyamides in a moisture-equiUbrated molten state undergo amide interchange where amine ends react with the amide groups. [Pg.259]

Condensation ofDianhydrides with Diamines. The preparation of polyetherknides by the reaction of a diamine with a dianhydride has advantages over nitro-displacement polymerization sodium nitrite is not a by-product and thus does not have to be removed from the polymer, and a dipolar aprotic solvent is not required, which makes solvent-free melt polymerization a possibiUty. Aromatic dianhydride monomers (8) can be prepared from A/-substituted rutrophthalimides by a three-step sequence that utilizes the nitro-displacement reaction in the first step, followed by hydrolysis and then ring closure. For the 4-nitro compounds, the procedure is as follows. [Pg.334]

The two-step poly(amic acid) process is the most commonly practiced procedure. In this process, a dianhydride and a diamine react at ambient temperature in a dipolar aprotic solvent such as /V,/V-dimethy1 acetamide [127-19-5] (DMAc) or /V-methy1pyrro1idinone [872-50-4] (NMP) to form apoly(amic acid), which is then cycHzed into the polyimide product. The reaction of pyromeUitic dianhydride [26265-89-4] (PMDA) and 4,4 -oxydiani1ine [101-80-4] (ODA) proceeds rapidly at room temperature to form a viscous solution of poly(amic acid) (5), which is an ortho-carboxylated aromatic polyamide. [Pg.396]

The 4,4 -MDA is sold commercially with a diamine assay of 98 —99%. The major impurity is the 2,4 -MDA isomer, which can be present in amounts up to 3%. PMDA products are normally defined by hydrogen equivalent weight and viscosity. Typical products exhibit a 50 hydrogen equivalent weight and a viscosity of 80 140 mPa-s(=cP) at 70°C. PMDA products normally contain, in addition to the isomers and oligomers of MDA, small amounts of aniline, water, chlorides, and various alkylated amines. AH MDA products should be stored in sealed containers in a cool dry area. [Pg.250]

One-part urethane sealants (Table 3) are more compHcated to formulate on account of an undesirable side reaction between the prepolymer s isocyanate end and water vapor which generates carbon dioxide. If this occurs, the sealant may develop voids or bubbles. One way to avoid this reaction is to block the isocyanate end with phenol and use a diketamine to initiate cure. Once exposed to moisture, the diketamine forms a diamine and a ketone. The diamine reacts with the isocyanate end on the prepolymer, creating a cross-link (10). Other blocking agents, such as ethyl malonate, are also used (11). Catalysts commonly used in urethane formulations are tin carboxylates and bismuth salts. Mercury salt catalysts were popular in early formulations, but have been replaced by tin and bismuth compounds. [Pg.311]

Uses. There may be some captive use of carbonyl sulfide for production of certain thiocarbamate herbicides (qv). One patent (38) describes the reaction of diethylamine with carbonyl sulfide to form a thiocarbamate salt which is then alkylated with 4-chloroben2yl haUde to produce 3 -(4-chloroben2yl) A[,A/-diethylthiocarbamate [28249-77-6] ie, benthiocarb [28249-77-6]. Carbonyl sulfide is also reported to be useful for the preparation of abphatic polyureas. In these preparations, potassium thiocyanate and sulfuric acid are used to first generate carbonyl sulfide, COS, which then reacts with a diamine ... [Pg.131]

Additive Polyimides. Rhc ne-Poulenc s Kin el molding compound and Kerimid impregnating resin (115), Mitsubishi s BT Resins (116), and Toshiba s Imidaloy Resin (117) are based on bismaleimide (4) technology. Maleic anhydride reacts with a diamine to produce a diimide oligomer (7). Eurther reaction with additional diamine (Michael addition) yields polyaminohismaleimide prepolymer with terminal maleic anhydride double bonds. Cure is achieved by free-radical polymerization through the terminal double bonds. [Pg.276]

In 1973 Du Pont commenced production of another aromatic polytunide fibre, a poly-(p-phenyleneterephthalamide) marketed as Kevlar. It is produced by the fourth method of polyamide production listed in the introductory section of this chapter, namely the reaction of a diamine with a diacid chloride. Specifically, p-phenylenediamine is treated with terephthalyl chloride in a mixture of hexamethylphosphoramide and V-methylpyrrolidone (2 1) at -10°C Figure 18.32). [Pg.514]

In a second step, the prepolymer was then reacted with a low molecular weight difunctional alcohol, commonly referred to as a diol or a diamine, to connect the prepolymer oligomers into a high molecular weight polyurethane. This step was referred to as the chain extension , resulting in the use of the term chain extenders to describe the low molecular weight diols or diamines that reacted with the prepolymer oligomers. [Pg.774]

Bell and Hall have incorporated an organometallic unit into a crown by using the ferrocenyl unit as part of the ring or as a third strand. The unit is incorporated either as the 1,1 -diformylferrocene or the corresponding acid. In the former case, the bis-imine is prepared and reduced to give the saturated crown (see structure 24). In the latter case, the acid is converted into its corresponding chloride and thence into the diamide by reaction with a diamine. Diborane reduction affords the saturated amino-crown. Structure 24 could be prepared by either of these methods but the dialdehyde approach was reported to be poor compared to the amide approach which afforded the product in ca. 60% yield . [Pg.53]

Macrocycles have been prepared by formation of macrocyclic imines as well as by using variations of the Williamson ether synthesis ". Typically, a diamine or dialdehyde is treated with its counterpart to yield the Schiff s base. The saturated macrocycle may then be obtained by simple reduction, using sodium borohydride, for example. The cyclization may be metal-ion templated. In the special case of the all-nitrogen macrd-cycle, 15, the condensation of diamine with glyoxal shown in Eq. (4.14), was unsuccess-ful ... [Pg.164]

Shortly after their first report of all-oxygen bridged cryptands, Dietrich, Lehn and Sauvage reported incorporation of sulfur in the strands. The experimental methods used were essentially similar to those applied in the syntheses of the parent cryptands. As in previous cases, a diacyl chloride was condensed with a diamine under high dilution conditions. In this case, however, the diamine contained sulfur atoms rather than oxygen. The synthesis of compound 5 was accomplished in two stages as illustrated below in Eq. (8.3). The first cyclization step affords the macrocyclic amine in 55% yield. The macrobicyclic product (5) is formed in 25% yield from the monocyclic diamine and the acid chloride. [Pg.349]

This is not the only method of forming tetrazo-compounds. Each amino-group of a diamine may be diazotised and coupled. Benzidine and its homologues, which ha e been utilised in this way, have a special value for the cotton dyer, as the shades produced are not only ery biilliant, but, unlike the maiorily of... [Pg.290]

Examine the structure of Nylon 6,6 (amide bonds have been assumed to adopt E geometries). What is the repeating unit How many monomers are in the strand Nylon 6,6 is made by combining two different molecules, a diacid and a diamine. Draw these molecules. [Pg.248]

Histamine. A diamine found in plant and animal tissues. It is involved in inflammatory responses. [Pg.452]

A similar reaction between a diamine and a diacid can also produce polyamides. [Pg.313]

Polyamides are produced by the reaction between a dicarboxylic acid and a diamine (e.g., nylon 66), ring openings of a lactam, (e.g., nylon 6) or by the polymerization of w-amino acids (e.g., nylon 11). The production of some important nylons is discussed in the following sections. [Pg.364]

When an amine reacts with an acid chloride, an amide is formed. What would happen, though, if a diamine and a diacid chloride were allowed to react Each partner could form two amide bonds, linking more and more molecules together until a giant polyamide resulted. In the same way, reaction of a diol with a diacid would lead to a polyester. [Pg.818]

The best known step-growth polymers are the polyamides, or nylons, first prepared by Wallace Carothers at the DuPont Company by heating a diamine with a diacid. Por example, nylon 66 is prepared by reaction of adipic acid (hexanedioic acid) with hexamethylenediamine (.1.,6-hexanediamine) at 280 °C. The designation "66" tells the number of carbon atoms in the diamine (the first 6) and the diacid (the second 6). [Pg.820]

Step-growth polymers, such as polyamides and polyesters, are prepared by reactions between difunctional molecules. Polyamides (nylons) are formed by reaction between a diacid and a diamine polyesters are formed from a diacid and a diol. [Pg.826]

We ve seen on several occasions in previous chapters that a polymer, whether synthetic or biological, is a large molecule built up by repetitive bonding together of many smaller units, or monomers. Polyethylene, for instance, is a synthetic polymer made from ethylene (Section 7.10), nylon is a synthetic polyamide made from a diacid and a diamine (Section 21.9), and proteins are biological polyamides made from amino acids. Note that polymers are often drawn by indicating their repeating unit in parentheses. The repeat unit in polystyrene, for example, comes from the monomer styrene. [Pg.1206]

This appears to be the first reported case of the Sommelet reaction starting with a diamine. [Pg.78]

When a diamine (molecule containing two NH2 groups) reacts with a dicarboxyiic acid (two COOH groups), a polyamide is formed. This condensation polymerization is entirely analogous to that used to make polyesters. In this case, the NH2 group of the diamine reacts with the COOH group of the dicarboxyiic acid ... [Pg.615]

Organic solvents are most commonly used, and encapsulating polymers include ethylcellu-lose, NC, polvvinylidene chloride, polystyrene, polycarbonate, polymethylmethacrylate, polyvinyl acetate and others. Inter facial polymerization produces a polymer such as nylon at the interface between layered solns of two precursor materials such as (in the case of a nylon) a diamine and a diacid (Refs 3 11). If the particle or drop-... [Pg.142]


See other pages where A-diamines is mentioned: [Pg.533]    [Pg.868]    [Pg.305]    [Pg.26]    [Pg.266]    [Pg.399]    [Pg.431]    [Pg.36]    [Pg.176]    [Pg.286]    [Pg.175]    [Pg.820]    [Pg.630]    [Pg.868]    [Pg.37]    [Pg.317]    [Pg.27]    [Pg.818]    [Pg.238]    [Pg.889]    [Pg.111]   
See also in sourсe #XX -- [ Pg.1259 ]




SEARCH



A,co-Diamines

Aminals (s. a. 1,1-Diamines

Diamines, as ligands

Use as Protecting Groups for Diols and Diamines

© 2024 chempedia.info