Type standardization

The drip-proof enclosure offers a ventilating sy.stem that is not dependent on external auxiliaries. Its installed cost is the lowest of all the enclosure types. Standard drip-proof ratings above 500 rpm may have a 1 15... 

Typldsung, /. type (or reference) solution, Typus, m. type, standard. 

Although the reactions themselves can be added to obtain the desired equation, the E° for this equation is not the sum of the E° values for the above three reactions. The E° for the desired equation is actually the weighted average of the E° values for reactions (1) to (3). It can be obtained by summing up the free energy changes for the three reactions. (For reactions of the same type, standard voltages are not additive AG° values are additive, however). When (1) and (2) (each multiplied by two) are added to (3) we obtain ... 

The flammable release frequencies may be estimated by counting all relevant system components whose failure could result in a flammable release and multiplying by failure rate data appropriate to the type, standard or design, use, and operating conditions. 

Depending on the type (standard vs. exclusive products) and the importance of a business transaction (small single-order vs. major multiyear supply contract), the levels of customer intimacy can vary between purchasing through the Internet with no personal contacts between the parties involved on one hand and frequent face-to-face meetings between the commercial (and other pertinent) functions of the involved companies on the other hand (see Figure 12.7) ... 

As said above it is possible to use the same Gaussian-type standard basis sets of ab initio theory for DFT calculations. Concerning the quality of the basis set which is necessary to obtain reliable results, it is advisable to use for Ge at least a split-valence basis set which should be augmented by a d-type polarization function such as 6-31G(d). Better basis sets of triple-zeta quality with more polarization functions up to 6-311G(3df) have been developed for Ge which belong to the standard basis sets in Gaussian 9831. Other basis sets for Ge are available, e.g., from the compilations of Huzinaga et al.32 and Poitier et al.33 and from the work of Aldrichs et al 34. 

The first essential step in color matching is to define the requirements of the color project. A standard form, that is, a color match request (CMR) form, is highly recommended. The CMR form, shown in Figure 5.2, asks the questions needed to define the sphere in which the color match must be accomplished polymer type, standard, competitive material, performance, volume, cost, and so on. Once the CMR is fully filled out, the scope of the match is defined and the process can be started. 

The most ready source of elastin of high purity is the ligamentum nuchae of the larger ruminants, and from this source a protein of constant composition can be isolated by a variety of methods depending on the solubilization and removal of other less inert tissue components. Because of the ease with which it may be isolated the elastin of bovine ligamentum nuchae has come to be regarded as the type standard, but it is by no means certain that elastins from other mammals or other tissues in the same mammal are of identical constitution. 

The most common use of the parallel interface is printer communication, and there are three major types standard, bidirectional, and enhanced parallel ports. Let s look at the differences between the three. 

After the national RA has received and validated an application, it classifies the application into one of three types standard, complex or me-too applications not supported by full data. 

Senile dementia of the Alzheimer s type Standard Error Single European Act of 1987... 

If the European Community were to require the introduction of standards similar to those being introduced in the United States, it could continue to enjoy the benefits of the diesel engine while reducing the environmental consequences. For example, Figure 4 shows what could happen if US type standards were introduced in Europe. In making these projections, the US standards for commercial vehicles were assumed to be introduced in 1995, the large car standards in 1989 and the small car standards in 1993. 

The contrast between the Commission proposal and US type standards is further illustrated in Figures 5, 6, 7 and 8. The figures show that not only can overall emissions be reduced, even with fairly large vehicle population growth, the pollution from individual categories can also be substantially lowered. 

Industry type (Standard Industrial Classification Code) Total waste quantity disposed of in all on-site industrial facilities (thousand tons) Percent of waste disposed of in landfills Percent of waste disposed of in surface impoundments Percent of waste disposed of in land application units Percent of waste disposed of in waste piles... 

Autrement dit, localement sur Spec(B) et Spec(A), une A-algebre etale B est du type standard et une A-algebre nette B est quotient d une A-algebre etale standard. 

The equipment shown in Fig. 5.23 (a type standardized in England) consists of a funnel and collecting vessel. The instrument is fixed in a stand, so that the funnel opening is at a level of 1.5 m above the ground. The funnel is protected from birds by wire netting. Because the device also captures precipitations, the sample of solid particles is obtained by the filtration or by the evaporation of water. 

The three basic types, standard, very and extremely inverse, are approximately represented by three ranges in which the exponential constant (a) should fall -... 

The most complex case is the analysis of all, or most, of the elements in a sample about which little or nothing is known. In this case a full qualitative analysis would be required before any attempt is made to quantify the matrix elements. Once the qualitative composition of the sample is known, again, one of three general techniques is typically applied use of type standardization, use of an influence coefficient method, or use of a fundamental parameter technique. 

Type standardization Provided that the total specimen absorption does not vary significantly over a range of analyte concentrations, and provided that enhancement effects are absent and that the specimen is homogeneous, a hnear relationship will be obtained between analyte concentration and measured characteristic line intensity. Where these provisos are met, type standardization techniques can be employed. 

It is sometimes convenient to refer to fire tests for plastics, rubbers, and textiles, and while tests exist that are specifically intended for individual materials, a large number of fire tests are intended for products. For example, the Motor Vehicle Safety Standard is intended for materials used inside motor vehicles irrespective of their type. Standards directories list a considerable number of fire tests for plastics and textiles but relatively few for rubber, although in practice a number of the plastics tests are used with rubbers. 

Resin type Standard Standard Standard Standard... 

Table 4.3 Means of Independent Variables for Full Sample and by Injury Type (standard deviation in parentheses)... 

The CP deposits on the inner surfaces of the primary main piping have been measured at every annual inspection period since the end of MK-I operation in July 1982. These measurements are made at 14 locations, shown in Fig. 18, using a Ge solid-state detector system. The detector system was calibrated with a piping mock-up using two planer type standard gamma-ray sources, " Mn and °Co, so that the absolute amounts of CP deposits could be obtained from the measured gamma-ray spectra. 

---