Styrene, copolymers with oxide

Blending methyl methacrylate-butadiene-styrene copolymer with poly(vinyl chloride) for instance was shown to decelerate the dehydrochlorination (leading to discoloration). The gel content, surface energy, and the spectroscopic characteristics of the blend was altered by the presence of the seccHid polymer [158]. In ethylene-propylene-diene rubber EPDM where the third monomer is ethylene-2-norbomene (NB), the photo-oxidation rate as measured by the accumulation of typical products such as hydroperoxides, varied linearly with the NB content [159]. The same held true for peroxide-crosslinked compounds of the same EPDM except that the linear relationship was found between the relative carbonyl absorbance on photoxidation and the amoiuit of peroxide used to crosslink the material... 

Alkanolamines are used as cross-linking and hardener accelerators in epoxy resins applications. Improved thermal and oxidative stability of polyvinyl alcohol, poly(phenylene ether), polystyrene, polypropylene, and polyethylene polymers are achieved by the addition of small amounts of the alkanolamines. Diethanolamine and morpholine act as initiators for the preparation of poly (alkyl methacrylate) in bulk or solution polymerization. The ethanolamines are efficient initiators for the preparation of polyvinyl chloride. Alkanolamines promote cross-linking of styrene copolymers with polystyrene or polyvinyl alcohol. Addition of alkanolamines to phenolic formaldehyde or urea formaldehyde resins affords improved electrical properties and increased water solubility. 

Fig. 11.46 Plot of spherulite radius as a function of time for poly(ethylene oxide) in blends with either ethylene-methacrylic acid or styrene-hydroxy styrene copolymer. With ethylene-methacrylic acid poly(ethylene oxide)/ethylene-methacrylic acid A 80/20, = 52.5 °C X 70/30, = 48 °C. With styrene-hydroxy styrene ...

II. B polyethylene glycol, ethylene oxide, polystyrene, diisocyanates (urethanes), polyvinylchloride, chloroprene, THF, diglycolide, dilac-tide, <5-valerolactone, substituted e-caprolactones, 4-vinyl anisole, styrene, methyl methacrylate, and vinyl acetate. In addition to these species, many copolymers have been prepared from oligomers of PCL. In particular, a variety of polyester-urethanes have been synthesized from hydroxy-terminated PCL, some of which have achieved commercial status (9). Graft copolymers with acrylic acid, acrylonitrile, and styrene have been prepared using PCL as the backbone polymer (60). 

It is evident that reactions of unsaturated polymers with bisnitrile oxides lead to cross-linking. Such a procedure has been patented for curing poly(butadiene), butadiene-styrene copolymer, as well as some unsaturated polyethers and polyesters (512-514). Bisnitrile oxides are usually generated in the presence of unsaturated polymers by dehydrochlorination of hydroximoyl chlorides. Cross-linking of ethylene-propylene-diene co-polymers with stable bisnitrile oxides has been studied (515, 516). The rate of the process has been shown to reduce in record with the sequence 2-chloroterephthalonitrile oxide > terephthalonitrile oxide > 2,5-dimethylterephthalonitrile oxide > 2,3,5,6-tetramethylterephthalo-nitrile oxide > anthracene-9,10-dicarbonitrile oxide (515). 

A totally different route based on dehydrogenation of a saturated polymer precursor was introduced by Francois et al. [49] (Scheme 2.9). The method is based on anionic copolymerization of cyclohexadiene with styrene, followed by oxidation with chloranil. Due to possible coupling of two styrene (or two cyclohexadiene) molecules, a block copolymer, containing oligo(phenylene vinylene) units separated by oligo(phenylacetylene) and oligo(phenylene) blocks, is obtained. To the best of our knowledge, it was, so far, used only in the synthesis of phenyl-substituted PPV 10. 

A. Mayer et al. examined poly(dimethylsiloxane)-bIock-poly(ethylene oxide) (PDMS-b-PEO), poly(styrene)-f)Iock-poly(ethylene oxide) (PS-b-PEO), polystyrene-block-poly(methacryhc acid) (PS-b-PMAA) as amphiphihc block copolymers with regard to their properties in stabilizing colloidal metal nanoparticles [37, 49]. All three polymers are successfully used to stabihze various transition metal coUoids... 

Uses Copolymerized with methyl acrylate, methyl methacrylate, vinyl acetate, vinyl chloride, or 1,1-dichloroethylene to produce acrylic and modacrylic fibers and high-strength fibers ABS (acrylonitrile-butadiene-styrene) and acrylonitrile-styrene copolymers nitrile rubber cyano-ethylation of cotton synthetic soil block (acrylonitrile polymerized in wood pulp) manufacture of adhesives organic synthesis grain fumigant pesticide monomer for a semi-conductive polymer that can be used similar to inorganic oxide catalysts in dehydrogenation of tert-butyl alcohol to isobutylene and water pharmaceuticals antioxidants dyes and surfactants. 

The range of monomers that can be incorporated into block copolymers by the living anionic route includes not only the carbon-carbon double-bond monomers susceptible to anionic polymerization but also certain cyclic monomers, such as ethylene oxide, propylene sulfide, lactams, lactones, and cyclic siloxanes (Chap. 7). Thus one can synthesize block copolymers involving each of the two types of monomers. Some of these combinations require an appropriate adjustment of the propagating center prior to the addition of the cyclic monomer. For example, carbanions from monomers such as styrene or methyl methacrylate are not sufficiently nucleophilic to polymerize lactones. The block copolymer with a lactone can be synthesized if one adds a small amount of ethylene oxide to the living polystyryl system to convert propagating centers to alkoxide ions prior to adding the lactone monomer. 

The hydrogenation of the centre block of SBS copolymer produced oxidation stable thermoplastic elastomer. This product was commercialized by the Shell Development Company under the trade name of Kraton G. The field of thermoplastic elastomers based on styrene, 1-3-butadiene or isoprene has expanded so much in the last 10 years that the synthetic rubber chemist produced more of these polymers than the market could handle. However, the anionically prepared thermoplastic system is still the leader in this field, since it produced the best TPR s with the best physical properties. These TPR s can accommodate more filler, which reduces the cost. For example, the SBS Kraton type copolymer varies the monomer of the middle block to produce polyisoprene at various combinations, then, followed... 

Dioxiranes constitute a new class of organic peroxides that possess great potential as oxidants with a variety of applications in synthetic organic chemistry.5 7 A new convenient route for the synthesis of silanol polymers has been developed by the selective oxidation of =Si—H bonds with dimethyldioxirane. A series of styrene-based silanol polymers and copolymers were synthesized (Scheme l).8 9 The precursor polymers and styrene copolymers containing =Si—H bond were first synthesized by free radical polymerization of the corresponding monomers or copolymerization of the... 

An important group of surface-active nonionic synthetic polymers (nonionic emulsifiers) are ethylene oxide (block) (co)polymers. They have been widely researched and some interesting results on their behavior in water have been obtained [33]. Amphiphilic PEO copolymers are currently of interest in such applications as polymer emulsifiers, rheology modifiers, drug carriers, polymer blend compatibilizers, and phase transfer catalysts. Examples are block copolymers of EO and styrene, graft or block copolymers with PEO branches anchored to a hydrophilic backbone, and star-shaped macromolecules with PEO arms attached to a hydrophobic core. One of the most interesting findings is that some block micelle systems in fact exists in two populations, i.e., a bimodal size distribution. 

Bahadur, P, N. V. Sastry, andY. K. Rao. 1988. Interaction studies of styrene-ethylene oxide block copolymers with ionic surfactants in aqueous solutitSholloids Surf.29 343-358. 

Gottschalk A, Muhlbach K, Seitz F, Stadler R, Auschra C (1994) Blends of poly(2,6-dimethyl-l,4-phenylene oxide) with styrene copolymers. Macromol Symp 83 127-146... 

Figure 9. Distribution of nitroxyl radicals concentration by thickness of sample underwent thermo-oxidative destruction at 120°C a - poly(acrylonitril-butadiene-styrene (ABS) copolymer), thickness of sample is 3,8mm b - polypropylene copolymer with polyethylene, thickness of sample is 3,4mm. The inset is the example of EPR-spectrum of nitroxyl radical in ABS-copolymer.

---