Styrene by dehydrogenation ethylbenzene

In 1869 Berthelot- reported the production of styrene by dehydrogenation of ethylbenzene. This method is the basis of present day commercial methods. Over the year many other methods were developed, such as the decarboxylation of acids, dehydration of alcohols, pyrolysis of acetylene, pyrolysis of hydrocarbons and the chlorination and dehydrogenation of ethylbenzene." ... 

Ethylbenzene is a high volume petrochemical used as the feed stock for the production of styrene via dehydrogenation. Ethylbenzene is currently made by ethylene alkylation of benzene and can be purified to 99.9%. Ethylbenzene and styrene plants are usually built in a single location. There is very little merchant sale of ethylbenzene, and styrene production is about 30x10 t/year. For selective adsorption to be economically competitive on this scale, streams with sufficiently high concentration and volume of ethylbenzene would be required. Hence, although technology has been available for ethylbenzene extraction from mixed xylenes, potential commercial opportunities are limited to niche applications. 

Application To produce polymer-grade styrene monomer (SM) by dehydrogenating ethylbenzene (EB) to form styrene using the Lummus/UOP "Classic" styrene process for new plants and the Lummus/UOP SMART process for revamps involving plant capacity expansion. 

The production of styrene by dehydrogenation of ethylbenzene is a good example (121). When rates of reaction are high, short diffusion lengths are required, suggesting structured, thin-layered catalytic reactors. When selectivity is an issue, this is even more the case. 

The Cg alkylaromatics fraction is formed by ethylbenzene and the three xylene isomers. Ethylbenzene is used as a raw material to produce styrene by dehydrogenation, or oxidative dehydrogenation. Para-xylene and ortho-xylene are catalytically oxidized to give terephthalic and phthalic acid. The meta-xylene isomer can also be oxidized to give isophthalic acid. The major industrial source of these products is the catalytic reforming of naphthas. The Cyclar process, can also produce xylenes from propane and butane. However, using this process, xylenes are formed less selectively than toluene or benzene in the BTX. 

Benzene was first isolated by Faraday in 1825 from the liquid condensed by compressing oil gas. It is the lightest fraction obtained from the distillation of the coal-tar hydrocarbons, but most benzene is now manufactured from suitable petroleum fractions by dehydrogenation (54%) and dealkylation processes. Its principal industrial use is as a starting point for other chemicals, particularly ethylbenzene, cumene, cyclohexane, styrene (45%), phenol (20%), and Nylon (17%) precursors. U.S. production 1979 2-6 B gals. 

Styrene is manufactured from ethylbenzene. Ethylbenzene [100-41-4] is produced by alkylation of benzene with ethylene, except for a very small fraction that is recovered from mixed Cg aromatics by superfractionation. Ethylbenzene and styrene units are almost always installed together with matching capacities because nearly all of the ethylbenzene produced commercially is converted to styrene. Alkylation is exothermic and dehydrogenation is endothermic. In a typical ethylbenzene—styrene complex, energy economy is realized by advantageously integrating the energy flows of the two units. A plant intended to produce ethylbenzene exclusively or mostly for the merchant market is also not considered viable because the merchant market is small and sporadic. 

Styrene manufacture by dehydrogenation of ethylbenzene is simple ia concept and has the virtue of beiag a siagle-product technology, an important consideration for a product of such enormous volume. This route is used for nearly 90% of the worldwide styrene production. The rest is obtained from the coproduction of propylene oxide (PO) and styrene (SM). The PO—SM route is complex and capital-iatensive ia comparison to dehydrogenation of ethylbenzene, but it stiU can be very attractive. However, its use is limited by the mismatch between the demands for styrene and propylene oxides (qv). 

Fig. 4. Manufacture of styrene by adiabatic dehydrogenation of ethylbenzene A, steam superheater B, reactor section C, feed—effluent exchanger D,...

Figure 5 illustrates a typical distillation train in a styrene plant. Benzene and toluene by-products are recovered in the overhead of the benzene—toluene column. The bottoms from the benzene—toluene column are distilled in the ethylbenzene recycle column, where the separation of ethylbenzene and styrene is effected. The ethylbenzene, containing up to 3% styrene, is taken overhead and recycled to the dehydrogenation section. The bottoms, which contain styrene, by-products heavier than styrene, polymers, inhibitor, and up to 1000 ppm ethylbenzene, are pumped to the styrene finishing column. The overhead product from this column is purified styrene. The bottoms are further processed in a residue-finishing system to recover additional styrene from the residue, which consists of heavy by-products, polymers, and inhibitor. The residue is used as fuel. The residue-finishing system can be a flash evaporator or a small distillation column. This distillation sequence is used in the Fina-Badger process and the Dow process. 

Two or more soHd catalyst components can be mixed to produce a composite that functions as a supported catalyst. The ingredients may be mixed as wet or dry powders and pressed into tablets, roUed into spheres, or pelletized, and then activated. The promoted potassium ferrite catalysts used to dehydrogenate ethylbenzene in the manufacture of styrene or to dehydrogenate butanes in the manufacture of butenes are examples of catalysts manufactured by pelletization and calcination of physically mixed soHd components. In this case a potassium salt, iron oxide, and other ingredients are mixed, extmded, and calcined to produce the iron oxide-supported potassium ferrite catalyst. 

Another appHcation for this type catalyst is ia the purification of styrene. Trace amounts (200—300 ppmw) of phenylacetylene can inhibit styrene polymerization and caimot easily be removed from styrene produced by dehydrogenation of ethylbenzene using the high activity catalysts introduced in the 1980s. Treatment of styrene with hydrogen over an inhibited supported palladium catalyst in a small post reactor lowers phenylacetylene concentrations to a tolerable level of <50 ppmw without significant loss of styrene. 

Alkylation. Ethylbenzene [100-41 -4] the precursor of styrene, is produced from benzene and ethylene. The ethylation of benzene is conducted either ia the Hquid phase ia the preseace of a Eriedel-Crafts catalyst (AlCl, BE, EeCl ) or ia the vapor phase with a suitable catalyst. The Moasanto/Lummus process uses an aluminum chloride catalyst that yields more than 99% ethylbenzene (13). More recently, Lummus and Union Oil commercialized a zeoHte catalyst process for Hquid-phase alkylation (14). Badger and Mobil also have a vapor-phase alkylation process usiag zeoHte catalysts (15). Almost all ethylbenzene produced is used for the manufacture of styrene [100-42-5] which is obtained by dehydrogenation ia the preseace of a suitable catalyst at 550—640°C and relatively low pressure, <0.1 MPa (<1 atm). 

The generation of caibocations from these sources is well documented (see Section 5.4). The reaction of aromatics with alkenes in the presence of Lewis acid catalysts is the basis for the industrial production of many alkylated aromatic compounds. Styrene, for example, is prepared by dehydrogenation of ethylbenzene made from benzene and ethylene. 

Styrene is made by dehydrogenation of ethylbenzene at high temperature using... 

Styrene. Still another process in which petroleum-derived ethylene serves as a raw material in the production of synthetic polymers is the reaction of ethylene with benzene to produce ethylbenzene, followed by dehydrogenation to styrene. 

Styrene manufacture by dehydrogenation of ethylbenzene is used for nearly 90% of the worldwide styrene production. The rest is obtained from the coproduction of propylene oxide (PO) and styrene (SM). 

Styrene (phenyl ethylene, vinyl benzene freezing point -30.6°C, boiling point 145°C, density 0.9059, flash point 31.4°C) is made from ethylbenzene by dehydrogenation at high temperature (630°C) with various metal oxides as catalysts, including zinc, chromium, iron, or magnesium oxides coated on activated carbon, alumina, or bauxite (Fig. 1). Iron oxide on potassium carbonate is also used. 

Styrene is produced from ethylbenzene by dehydrogenation (Fig. 1). Many lower molecular weight aliphatic ketones are made by dehydration... 

Styrene (phenylethylene or vinyl benzene, C6H5-CH=CH2) is made from ethylene by reaction with benzene to form ethylbenzene, followed by dehydrogenation. Over 50 percent of manufactured styrene is polymerized to polystyrene for toys, cups, containers, and foamed materials used for insulation and packing. The rest is used to make styrene copolymers, such as styrene-butadiene rubber (SBR). 

---